Шлифовальная машина RYOBI EBS800. Инструкция на русском языке

ORIGINAL INSTRUCTIONS                EN
TRADUCTION DES INSTRUCTIONS ORIGINALES  FR
UBERSETZUNG DER ORIGINALANLEITUNG    DE
TRADUCCION DE LAS INSTRUCCIONES ORIGINALES  ES
TRADUZIONE DELLE ISTRUZIONI ORIGINALI  IT
VERTALING VAN DE ORIGINELE INSTRUCTIES  NL
TRADUCAO DAS INSTRUCOES ORIGINAIS    PT
OVERS?TTELSE AF DE ORIGINALE INSTRUKTIONER  DA
EBS800                      OVERSATTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA  SV
ALKUPERAISTEN OHJEIDEN SUOMENNOS     FI
OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE  NO
EBS800V                      ПЕРЕВОД ОРИГИНАЛЬНЫХ ИНСТРУКЦИЙ      RU
TLUMACZENIE INSTRUKCJI ORYGINALNEJ
PL
PREKLAD ORIGINALNICH POKYNU          CS
AZ EREDETI UTMUTATO FORDITASA        HU
TRADUCEREA INSTRUCTIUNILOR ORIGINALE  RO
TULKOTS NO ORIGINALAS INSTRUKCIJAS   LV
ORIGINALIU INSTRUKCIJU VERTIMAS      LT
ORIGINAALJUHENDI TOLGE               ET
PRIJEVOD ORIGINALNIH UPUTA           HR
PREVOD ORIGINALNIH NAVODIL           SL
PREKLAD ORIGINALNYCH POKYNOV         SK
????????? ??? ?????????? ???????     EL
ORIJINAL TALIMATLARIN TERCUMESI      TR

English     EN
FR
DE
ES
SPECIAL SAFETY RULES                                   WARNING              IT
¦  Hold power tool by insulated gripping surfaces,   Do not at any time let brake ? uids, gasoline, petroleum-  NL
because the belt may contact its own cord. Cutting a   based products, penetrating oils, etc. come in contact   PT
“live” wire may make exposed metal parts of the power   with plastic parts. They contain chemicals that can   DA
tool “live” and could give the operator an electric shock.  damage, weaken or destroy plastic.  SV
¦  Always wear safety goggles and a dust mask when                       FI
sanding, especially sanding overhead.  Electric tools used on  ? berglass material, wallboard,   NO
¦  A suitable breathing respirator must be worn while   spackling compounds, or plaster are subject to accelerated   RU
sanding lead paint, some woods and metal to avoid   wear and possible premature failure because the ? berglass
breathing the harmful/toxic dust or air.  chips and grindings are highly abrasive to bearings,   PL
¦  The machine is not suitable for wet sanding.  brushes, commutators, etc. Consequently, we do not   CS
recommend using this tool for extended work on these   HU
¦  Do not use sanding belt larger than needed.  types of materials. However, if you do work with any of
these materials, it is extremely important to clean the tool   RO
WARNING               using compressed air.                 LV
LT
Do not throw sanding dust on an open fire because
materials in ? ne particle form may be explosive.      WARNING             ET
Always wear safety goggles or safety glasses with side   HR
shields during power tool operation or when blowing   SL
WARNING                dust. If operation is dusty, also wear a dust mask.  SK
If the replacement of the supply cord is necessary, this                   EL
has to be done by the manufacturer or his agent in order                   TR
to avoid a safety hazard.            LUBRICATION
All of the bearings in this tool are lubricated with a suf? cient
amount of high grade lubricant for the life of the unit
under normal operating conditions. Therefore, no further
INTENDED USE                          lubrication is required.
You may use this product for the purposes listed below:
¦  Sanding on wood surfaces.       CLEANING THE SANDING BELT
The sanding belt that came with your sander is made to
¦  Removing rust from and sanding steel surfaces.  be re-used. Therefore, it is important that it be cleaned
periodically to remove sanding residue and foreign material
MAINTENANCE                           that can accumulate over time. One of the ways to clean
sanding belt is to rub the sheets with a hard rubber block.
You can also use the clean rubber sole of a shoe.
WARNING
The tool should never be connected to a power supply       WARNING
when you are assembling parts, making adjustments,   Always remove the sanding belt from sander before
cleaning, performing maintenance, or when the tool is   cleaning. Failure to do so could cause serious personal
not in use. Disconnecting the tool will prevent accidental   injury.
starting that could cause serious injury.
WARNING
ENVIRONMENTAL PROTECTION
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or   Recycle raw materials instead of disposing
cause product damage.                       of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial   SYMBOL
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.
Safety Alert
V   Volts
1

English
Hz   Hertz
Alternating current                       Plug in
W    Watts
no   No-load speed
min??  Revolutions or reciprocations per minute  Lock
CE Conformity
Conformance to technical regulations     Unlock
Double insulation
Information
Please read the instructions carefully before
starting the product.
Tip
Wear ear protection
Wear eye protection
Wear safety hand gloves
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
ICONS IN THIS MANUAL
Safety
Unpacking
Getting started
Operation
Safety alert
Unplug
2