Перфоратор MAKITA HR5001C. Инструкция на русском языке

Rotary Hammer
50 mm (2”)
MODEL HR5001C
003102
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools . com

SPECIFICATIONS
Model                              HR5001C
Carbide-tipped bit           50 mm (2”)
Capacities
Core bit                160 mm (6-1/4”)
No load speed (RPM)                    120 - 240/min.
Blows per minute                      1,100 - 2,150
Overall length                       610 mm (24”)
Net weight                          10 kg (22 lbs)
• Manufacturer reserves the right to change specifications without notice.
• Specifications may differ from country to country.
GENERAL SAFETY RULES                                              USA002-2
(For All Tools)
WARNING:
Read and understand all instructions. Failure to follow all
instructions listed below, may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area                            3. Keep bystanders, children, and visitors
away while operating a power tool. Distrac-
1. Keep your work area clean and well lit.
tions can cause you to lose control.
Cluttered benches and dark areas invite acci-
dents.                            Electrical Safety
2. Do not operate power tools in explosive  4. Double insulated tools are equipped with
atmospheres, such as in the presence of  a polarized plug (one blade is wider than
flammable liquids, gases, or dust. Power  the other.) This plug will fit in a polarized
tools create sparks which may ignite the dust  outlet only one way. If the plug does not fit
or fumes.                            fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified elec-
trician to install a polarized outlet. Do not
2

change the plug in any way. Double insula-  balance enables better control of the tool in
tion    eliminates the need for the three wire  unexpected situations.
grounded power cord and grounded power  14. Use safety equipment. Always wear eye
supply system.                       protection. Dust mask, non-skid safety
5. Avoid body contact with grounded sur-  shoes, hard hat, or hearing protection must
faces such as pipes, radiators, ranges and  be used for appropriate conditions. Ordinary
refrigerators. There is an increased risk of  eye or sun glasses are NOT eye protection.
electric shock if your body is grounded.
Tool Use and Care
6. Do not expose power tools to rain or wet  15. Use clamps or other practical way to
conditions. Water entering a power tool will  secure and support the workpiece to a
increase the risk of electric shock.
stable platform. Holding the work by hand or
7. Do not abuse the cord. Never use the cord  against your body is unstable and may lead
to carry the tools or pull the plug from an  to loss of control.
outlet. Keep cord away from heat, oil,  16. Do not force tool. Use the correct tool for
sharp edges or moving parts. Replace  your application. The correct tool will do the
damaged cords immediately. Damaged   job better and safer at the rate for which it is
cords increase the risk of electric shock.
designed.
8. When operating a power tool outside, use  17. Do not use tool if switch does not turn it
an outdoor extension cord marked “W-A”  on or off. Any tool that cannot be controlled
or “W”. These cords are rated for outdoor  with the switch is dangerous and must be
use and reduce the risk of electric shock.
repaired.
Personal Safety                      18. Disconnect the plug from the power
9. Stay alert, watch what you are doing and  source before making any adjustments,
use common sense when operating a    changing accessories, or storing the tool.
power tool. Do not use tool while tired or  Such preventive safety measures reduce the
under the influence of drugs, alcohol, or  risk of starting the tool accidentally.
medication. A moment of inattention while  19. Store idle tools out of reach of children
operating power tools may result in serious  and other untrained persons. Tools are
personal injury.                     dangerous in the hands of untrained users.
10. Dress properly. Do not wear loose cloth-  20. Maintain tools with care. Keep cutting
ing or jewelry. Contain long hair. Keep  tools sharp and clean. Properly maintained
your hair, clothing, and gloves away from  tools with sharp cutting edges are less likely
moving parts. Loose clothes, jewelry, or long  to bind and are easier to control.
hair can be caught in moving parts.
21. Check for misalignment or binding of
11. Avoid accidental starting. Be sure switch  moving parts, breakage of parts, and any
is off before plugging in. Carrying tools with  other condition that may affect the tools
your finger on the switch or plugging in tools  operation. If damaged, have the tool ser-
that have the switch on invites accidents.  viced before using. Many accidents are
12. Remove adjusting keys or wrenches   caused by poorly maintained tools.
before turning the tool on. A wrench or a  22. Use only accessories that are recom-
key that is left attached to a rotating part of  mended by the manufacturer for your
the tool may result in personal injury.  model. Accessories that may be suitable for
13. Do not overreach. Keep proper footing  one tool, may become hazardous when used
and balance at all times. Proper footing and  on another tool.
3