На сайте 124171 инструкция общим размером 502.73 Гб , которые состоят из 6277477 страниц
Руководство пользователя ROLAND MX-1. Основные функции, характеристики и условия эксплуатации изложены на 1 странице документа в pdf формате.
Доступно к просмотру 1 страница. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.
Before using this unit, carefully read leaflet “USING THE UNIT SAFELY” . After reading, keep the Copyright © 2015 ROLAND CORPORATION document(s) including those sections where it will be available for immediate reference. Owner’s Manual English All rights reserved. No part of this publication may be reproduced in any form without the * 5 1 0 0 0 4 4 3 3 3 - 0 1 * written permission of ROLAND CORPORATION. Rear Panel [POWER] switch DC IN jack USB HOST (1–4) ports USB (O) port MIDI (IN, OUT) connectors INPUT (1–4, 5/6) jacks This turns the power on/off. Connect the included AC adaptor here. These are dedicated USB audio input ports for use only with Use a commercially available USB 2.0 cable to connect this For connecting MIDI device. Connect external sound sources to these jacks. By switching * When powering-on your equipment, you must turn on each device * To prevent the inadvertent disruption of power to your unit (should AIRA products (such as the TR-8, TB-3, VT-3, and SYSTEM-1). By port to your computer. It can be used to transfer USB MIDI their settings, you can use INPUT 1–4 jacks either as monaural in the following order: devices connected to the input jacks&the the plug be pulled out accidentally), and to avoid applying undue using commercially available USB 2.0 cables to connect your and USB audio data. You must install the USB driver before DIGITAL IN/OUT jack inputs (1, 2, 3, 4) or as stereo inputs (1/2, 3/4). INPUT 5/6 jacks MX-1&devices connected to the output jacks. Failure to observe stress to the jack, anchor the power cord using the cord hook, as AIRA products, you can input their audio output (stereo) to connecting the MX-1 to your computer. Download the USB A two-channel (stereo) digital input/output device can be support stereo input. this order could cause malfunctions or damage your equipment. shown in the illustration. the MX-1 and mix the audio outputs. The USB HOST 3 port can driver from the Roland website. For details, refer to Readme. connected here. Switch the setting of this jack between input/ * Do not use connection cables that contain a built-in resistor. When powering-off your equipment, you must turn off each device supply USB bus power. The TB-3 or VT-3, which support bus htm which is included in the download. output depending on the device that you connect. in the following order: devices connected to the output jacks&the MIX OUT (L/MONO, R) jacks MX-1&devices connected to the input jacks. power, can be connected here. AUX SEND (L, R) jacks Cord hook Product Support Connect your amp or monitor speaker here. These jacks * Before turning the unit on/off, always be sure to turn the volume * Do not connect any USB device other than an AIRA These jacks output the send audio to an external effect unit. down. Even with the volume turned down, you might hear some product. http://www.roland.com/support/ output the master audio. sound when switching the unit on/off. However, this is normal and The cord of the * The master audio is not output. * Do not use connection cables that contain a built-in resistor. does not indicate a malfunction. supplied AC adaptor Product Support * This unit is equipped with a protection circuit. A brief interval (a few http://www.roland.com/support/ AUX RETURN (L, R) jacks PHONES jack seconds) after turning the unit on is required before it will operate These jacks input the return audio from an external effect unit. Connect headphones here. normally. PHONES Effect Section This adjusts the headphone output. The headphones let you listen to the master audio simultaneously with the sound of the The effect section contains BEAT FX which lets you modify the sound by applying an effect to each channel, and MASTER FX channel selected by the [SELECT] button. Even if you lower the level of the selected channel or mute it, you can listen to its sound which applies an effect to the mixed sound of all channels. by turning the [MIXING] knob to the SELECT position; this lets you prepare the next song or make settings for it. Pad [1]–[16] [LEVEL] knob [MIXING] knob Select the steps at which the BEAT FX and MASTER FX are applied. This adjusts the volume of the headphones. This adjusts the balance between the master output and BEAT FX The balance adjusted by the [MIXING] knob is output without the channel whose [SELECT] button is lit. Turning the knob further change. toward SELECT decreases the volume of the master output; For each channel, you can edit the filter, slicer, or side chain Name Explanation turning the knob toward MASTER decreases the volume of the settings, and modify the sound by turning them on/off for each [FILTER] button Applies a filter. selected channel. step. The BEAT FX effect is synchronized to the tempo of the [SIDE CHAIN] button Applies a side chain. device that’s specified as the clock master. NOTE &”Operation procedure: BEAT FX settings” [SLICER] button Applies a slicer. When the [MIXING] knob is in the SELECT position, the sound is output at the volume before the adjustment of the MX-1’s MASTER FX [LEVEL] fader is applied. Before you audition the sound of the selected channel, you should turn down the [LEVEL] knob to avoid This applies an effect such as delay, filter, scatter, or roll to the mixed sound of all channels. By using the combination function, damaging your hearing with high volume. you can switch the MASTER FX type at each step in synchronization with the tempo.&”Operation procedure: MASTER FX settings” AUX * You can’t specify a different MASTER FX type for each channel. * If the tempo is too fast, the type might not switch at the intended step when using the combination function. Here you can adjust the output level of the AUX SEND jacks and the input level from the AUX RETURN jacks. Name Explanation [SEND] knob [RETURN] knob Use this knob to edit the effect parameters. Adjusts the send level that is output from the AUX SEND jacks. Adjusts the return level that is input from the AUX RETURN The CA indications at the left and right of the [MASTER FX] knob change their appearance jacks. [MASTER FX] knob depending on the knob position. C lit: LOW side CA lit: OFF A lit: HIGH side CHANNEL SETTING [TIME] button Specifies the delay time or the frequency response of the filter etc. [COMBI] button Makes settings for the combination function. Here you can adjust the gain and pan of each channel, as well as settings such as BEAT FX and TONE / FILTER FX. [DELAY] button Applies a delay. [FILTER] button Applies a filter. [SCATTER] button Applies a scatter. Name Explanation [FLANGER] button Applies a flanger. Adjusts the input gain. The level meter indicates the input gain.Range: -20–30 dB [GAIN] button [BIT CRUSH] button Applies a bit crusher (producing a distinctive noisy sound). &”Operation procedure: Adjusting the input gain” [ROLL] button Produces a roll (repeated playback). Adjusts the pan (stereo position). The monaural channels (1–4) provide a pan adjustment; the stereo channels Mixer Section (5/6, DIGITAL, USB 1–4, PC) provide a left/right balance adjustment. [PAN] button Range: L50–C0 (Center)–R50 Here you can adjust settings such as level, TONE / FILTER FX, BEAT FX, and MASTER FX. &”Operation procedure: Adjusting the pan” TEMPO [TONE] button Switches the TONE/FILTER FX type.&”Operation procedure: TONE/FILTER FX settings” Name Explanation [AUX] button Adjusts the volume that is output to the AUX SEND jacks.&”Operation procedure: Setting the AUX level” [TONE/FILTER] knob Edits the TONE/FILTER FX parameter that’s selected by the [TONE] button. Here you can specify the tempo and specify the MIDI clock synchronization source (clock master). You can also adjust the Selects the steps at which BEAT FX is applied, and adjusts the depth level. Selects the channel whose “CHANNEL SETTING” parameters you will edit. amount of shuffle (rhythmic bounce) on the BEAT FX and combination function. [BFX] button &”Operation procedure: BEAT FX settings” * Even if the channel whose [SELECT] button is lit is not being output from the master Name Explanation Specifies how the [LEVEL] fader changes the level (fader curve). output (i.e., if the channel is muted or its level is lowered), you can turn the [MIXING] [FADER] button [TEMPO] knob Specifies the tempo. The tempo value is shown in the display above the knob. Range: 40.0–300.0 &”Operation procedure: Fader curve settings” knob toward the SELECT position to audition the sound. [SHUFFLE] button Adjust the amount of shuffle (rhythmic bounce). Range: -50–0–50 [SELECT] button To select one channel Press the [SELECT] button. [FINE] button Specifies the tempo below the decimal point. To select multiple Hold down the [SELECT] button and press the [SELECT] Selects the MIDI clock synchronization source (clock master).&”Operation procedure: channels button of another channel. [SYNC] button Synchronization settings” SCENE MEMORY Hold down the CHANNEL SETTING button and press the [TAP] button To set the tempo, tap this button several times at the desired interval. To select all [SELECT] button. Scene memory stores the settings of the CHANNEL SETTING section, the effect section, and the mixer section as a single scene, Applies the BEAT FX to the sound of the channel. * If the clock master setting is other than “INT,” the [TEMPO], [SHUFFLE], [FINE], and [TAP] buttons are inoperable. allowing you load these settings when necessary. You can store up to 64 scenes (16 pads x 4 banks). &”Operation procedure: BEAT FX settings” &”Operation procedure: Storing and recalling scene memories” [BFX] button * The button blinks if the BEAT FX depth level is set to 0. Adjust the depth level as Master Out Section [RECALL] button [STORE] button necessary. Recall a scene memory. Store a scene memory. Specifies whether the input sound is output without change (unlit) or the MASTER FX Here you can adjust the master level and the mastering effect settings. [MFX] button applied (lit). &”Operation procedure: MASTER FX settings” Name Explanation START/STOP Adjusts the level. [MASTER LEVEL] knob Adjusts the volume that is output from the MIX OUT jacks. [LEVEL] fader You can specify the fader curve by which the level changes. Edits the MASTERING FX (mastering effect) settings. Starts (lit) or stops (blinking) the BEAT FX. &”Operation procedure: Fader curve settings” [MASTERING] button &”Operation procedure: MASTER FX settings” When you start, BEAT FX applies in synchronization with the tempo at the steps you specify using the pads [1]–[16]. You can also [MUTE] button Mutes the sound of the channel. use the combination function with MASTER FX so that the type is switched for each step in synchronization with the tempo. Level meter Indicates the master output level. If the [GAIN] button is lit, the meter indicates the input level of the selected channel. Operation procedure Connecting devices Adjusting the input gain 6. Select the BEAT FX type and variation. MASTERING FX settings 5. Turn the [RETURN] knob to adjust the output volume of 7 RECALL the AUX RETURN jacks. Connect your equipment correctly as described below. 1. Press the [GAIN] button to make it light. Type Explanation The MASTERING FX applies to all of the audio input. &”System Settings: AUX RETURN rooting” 1. Press the [RECALL] button to make it light. * To prevent malfunction and equipment failure, always turn 2. Press the [SELECT] button of the channel whose input Cuts a specific frequency region from the * If the sound distorts when you enable the MASTERING FX, 2. Use the [VALUE] knob or pads [1]–[16] to select the scene number that you want to recall. down the volume, and turn off all the units before making gain you want to adjust; the button lights. FILTER input sound. lower the level of each channel until the sound is no longer Fader curve settings any connections. distorted. If you used pads [1]–[16] to select a scene, the scene is The value of the current setting is shown in the display SIDE CHAIN Adjusts (“ducks”) the volume of the audio You can specify the way in which the level changes when you recalled immediately.Alternatively, you can use the [VALUE] 7 Connecting external audio sources above the [VALUE] knob, and the level meter changes to input. 1. Press the [MASTERING] button to make it light. move the [LEVEL] fader (i.e., the fader curve). knob to select “NAn (Manual),” which makes the MX-1 use External audio sources such as an analog synth or a DJ show the input gain. SLICER Periodically cuts the output of the input The MASTERING FX is enabled. 1. Press the CHANNEL SETTING [FADER] button to make it the current settings of the [TONE/FILTER FX] knobs and player can be connected to the INPUT 1–4 or 5/6 jacks, or &”Mixer Section: [SELECT] button” sound. 2. Hold down the [MASTERING] button and turn the [LEVEL] faders. to the DIGITAL IN jack. 3. Turn the [VALUE] knob to adjust the gain. * To select the variation, hold down the [FILTER], [SIDE [TEMPO] knob to select the type. light. * Immediately after a scene is recalled, the physical Adjust the gain so that the signal does not exceed 0 dB on CHAIN], or [SLICER] button and turn the [VALUE] knob. 2. For the channel whose fader curve you want to specify, positions of the [LEVEL] faders, [TONE] knobs, and NOTE the level meter (the green LED at the top). Auditioning the selected channel press the [SELECT] button to make it light. [MASTER FX] knob may differ from the recalled values. 7. Use pads [1]–[16] to select the steps at which BEAT FX By lighting the [SELECT] button of multiple channels, you With the default settings, INPUT 1–4 are assigned as applies. can set all of the selected channels to the same fader curve * If the recalled value differs from the physical position of monaural inputs, and DIGITAL IN/OUT is assigned as digital Adjusting the pan * The BEAT FX effect applies at the timing of the pads that You can audition the sound of the selected channel in your setting. a [LEVEL] fader, the periphery of the fader blinks. input. If you want to input stereo sources to INPUT 1–4, or are lit. headphones.&”PHONES” 3. If you used the [VALUE] knob to select a scene, press the if you want to use DIGITAL IN/OUT as digital output, make 1. Press the [PAN] button to make it light. 1. Press the [SELECT] button of the channel whose sound 3. Turn the [VALUE] knob to select the fader curve. [RECALL] button to recall the scene. the appropriate changes to the system settings. 8. Turn the [VALUE] knob to adjust the depth level. you want to audition; the button lights. &”System Settings: Channel link” 2. Press the [SELECT] button of the channel whose pan you By holding down the CHANNEL SETTING [BFX] button and Operation with a DAW want to adjust; the button lights. turning the [VALUE] knob you can adjust the duration (gate &”Mixer Section: [SELECT] button” 7 Connecting AIRA products &”Mixer Section: [SELECT] button” time) during which the BEAT FX effect is applied. 2. Turn the [MIXING] knob to adjust the volume balance AIRA products such as the TR-8 and TB-3 can be connected 3. Turn the [VALUE] knob to adjust the pan. between the selected channel and the master output. In addition to mixing the sounds of AIRA products and other hardware, the MX-1 can work with a DAW on your computer via a commercially available USB 2.0 cable to a USB HOST MASTER FX settings * Turning the knob toward SELECT, you can listen only to to mix the playback of the DAW and operate as a DAW port. TONE/FILTER FX settings the sound of the selected channel. controller. 7 Connecting computer MASTER FX lets you apply effects such as delay, filter, and 3. Turn the [LEVEL] knob to adjust the volume of the To use the MX-1 with your DAW, you’ll need to change the With the default settings, TONE/FILTER FX is set to “FILTER1.” scatter. By using the combination function, you can switch the headphones. system settings. If you want to mix the audio playback from your computer, effect type at each step. use a commercially available USB 2.0 cable to connect the 1. Press the [TONE] button to make it light. &”System Settings: Mixer mode” MX-1’s USB port to your computer. You must install the USB 2. Press the [SELECT] button of the channel which you want 1. On each channel to which you want to apply the MASTER Setting the AUX level Storing and recalling scene memories driver before connecting the MX-1 to your computer. to apply; the button lights. FX, press the [MFX] button to make it light. &”Rear Panel: USB (O) port” &”Mixer Section: [SELECT] button” 2. Select the MASTER FX type. You’ll use AUX when using an external effect device via a When you store a scene memory, the current settings for * With the default settings, the audio playback from your 3. Turn the [VALUE] knob to select the type. send/return connection. the channels, effect section, and mixer section are stored in Main Specifications Roland MX-1: MIX PERFORMER computer is input to the PC channel in stereo. Effect Type Explanation 1. Press the CHANNEL SETTING [AUX] button to make it the MX-1 as a single scene. You can recall the stored settings * If no AIRA product is connected to the USB HOST ports, DELAY Delay is applied. light. when necessary. Power Supply AC adaptor the audio playback from your computer can be input to Number Type Explanation FILTER Filter is applied. 2. For each channel that you want to send to the AUX SEND 7 STORE Current Draw 1700mA USB 1–4 channels and mixed. 1 FILTER 1 (FL1) Low pass and high pass filters jacks, press the [SELECT] button to make the button Dimensions 400 (W) x 264 (D) x 65 (H) mm &”System Settings: Mixer mode” 2 FILTER 2 (FL2) are applied. “Scatter” adds a digital-feeling groove to the light. 1. Press the [STORE] button to make it light. 15-3/4 (W) x 10-7/16 (D) x 2-9/16 (H) inches loop playback by exchanging individual steps &”Mixer Section: [SELECT] button” 7 Connecting MIDI device 3 TONE 1 (Tn1) The volume of the low- SCATTER within the loop playback and also by changing 3. Turn the [VALUE] knob to adjust the send level. 2. Use the [VALUE] knob or pads [1]–[16] to select the scene Weight 1.81 kg number that you want to store. frequency and high-frequency 4 lbs The MX-1 can receive MIDI Clock (F8) data to synchronize 4 TONE 2 (Tn2) region is changed. the playback direction or gate length. 4. Turn the [SEND] knob to adjust the output volume of the The [STORE] button blinks. Accessories AC adaptor, Owner’s manual, Leaflet “USING THE its tempo. It can also receive MIDI Start (FA) and MIDI Stop 5 EQ LOW 1 (Lo1) The volume of the low- FLANGER Flanger is applied. AUX SEND jacks. 3. Press the [STORE] button to store the settings. UNIT SAFELY“, Ableton Live Lite Serial Number Card (FC) to start/stop itself. BIT CRUSH Distorts the waveform, producing a distinctive 6 EQ LOW 2 (Lo2) frequency region is changed. noisy sound. &”System Settings: AUX SEND rooting” * In the interest of product improvement, the 7 Connecting external effect device 7 EQ HI1 (Hi1) The volume of the high- ROLL Plays the sound repeatedly. specifications and/or appearance of this unit are subject If you want to use an external effect device or amp via the 8 EQ HI2 (Hi2) frequency region is changed. to change without prior notice. send/return jacks, connect your equipment to the AUX The low-frequency and high- * To select a variation, hold down the button for the SEND jacks and AUX RETURN jacks. 9 ISOLATOR 1 (iS1) frequency regions are cut. corresponding type and turn the [TEMPO] knob. Various Settings &”Operation procedure: Setting the AUX level” The low-frequency, Middle- 3. Hold down the [TIME] button and turn the [TEMPO] knob 10 ISOLATOR 2 (iS2) frequency and high-frequency to adjust the parameter. Synchronization settings regions are cut. 4. Turn the [MASTER FX] knob to adjust the depth. Restoring the Factory Settings (Factory Reset) Settings Operation Value/ State Explanation 4. Turn the [TONE/FILTER] knob of each channel to adjust * The MASTER FX effect is OFF when the [MASTER FX] Unlit (Off) * Specifies whether MASTER FX is applied to the Here’s how to select the MIDI clock master in order to the depth. knob is in the center position (CA lit); turning the knob 1. While holding down the [RECALL] button, turn on the power. AUX RETURN Press the Pad [3] input from the AUX RETURN jacks (lit) or is not rooting synchronize the tempo of the MX-1 and the connected * TONE/FILTER FX is off when the [TONE/FILTER] knob is left or right applies the effect that’s specified for each The display indicates “rSt” and the [START/STOP] button blinks. Lit (On) applied (unlit). devices. selected variation. in the center position; turning the knob to left or right 2. Press the [START/STOP] button to execute the factory reset. Unlit (Off) * Specifies whether data received from the MIDI IN 1. Press the [SYNC] button to make it light. applies the effect of the selected type. 7 Switching the type at each step (Combination 3. When the display indicates “CNP,” turn the MX-1’s power off, then on again. MIDI through Press the Pad [4] Lit (On) connector will be retransmitted from the MIDI OUT connector (On) or will not be retransmitted (Off). 2. Turn the [TEMPO] knob to select the MIDI clock master. function) System Settings Mixes the AIRA products or other hardware that The clock master you select blinks in the display above the BEAT FX settings The combination function lets you assign a MASTER FX NiX is connected to the MX-1. If no AIRA products are [TEMPO] knob. type to each individual step, adding change to the sound. Here’s how to change the MX-1’s system settings. (MIXER mode) * connected to the USB HOST ports, the playback By using BEAT FX you can apply an effect such as filter, side * You can assign one type to each step. from the computer is input to USB channels 1–4 chain, or slicer to individual channels. BEAT FX can also be 1. While holding down the [GAIN] button, turn on the power. and can be mixed. Display Explanation turned on/off for individual steps to create change in the 1. Press the [START/STOP] button. 2. Use the buttons, knobs and the pads to change the settings. MIDI channels (1–11) are assigned starting at If a MIDI clock is being input from a connected sound. 2. Press the [COMBI] button to make it light. The default values or states are marked with “*.” SvR channel 1 of the MX-1, allowing the MX-1 to operate as a USB controller for your DAW. device, the MX-1 synchronizes to that MIDI 1. Press the CHANNEL SETTING [BFX] 3. Hold down the [COMBI] button and turn the [TEMPO] (CONTROL SURFACE * The sound of hardware connected to the MX-1 clock. If multiple MIDI clocks are being input, button to make it light. knob to select a pattern (combination of the MASTER FX). Settings Operation Value/ State Explanation Press the [TONE] mode) is not mixed; the sound adjusted by the [GAIN] the MX-1 synchronizes to one of them in the Press the channel 1 Channel 2 lit * Supports monaural input. Mixer mode button and turn the button is sent to the computer. The sound of Avto (*) following order of priority. You can also edit the pattern. or 2 [SELECT] button Channel 2 unlit Supports stereo input. [VALUE] knob the PC channel is sent from the MIX OUT jacks. 4. Turn the [MASTER FX] knob to adjust the depth. Channel link The MX-1 operates with the DAW on your 1. USB (O) port 4. USB HOST 2 port Press the channel 3 Channel 4 lit * Supports monaural input. computer to mix the playback of multiple tracks. 2. MIDI IN connector 5. USB HOST 3 port or 4 [SELECT] button Channel 4 unlit * Supports stereo input. 3. USB HOST 1 port 6. USB HOST 4 port 2. Press the [START/STOP] button to start the BEAT FX. 7 Editing the pattern DIGITAL jack Press the DIGITAL Unlit The jack operates as an output jack. EXT * The gain of the DAW playback cannot be adjusted by the MX-1. Adjust the output levels channel [SELECT] Int The MX-1 is the MIDI clock master. 3. On each channel to which you want to apply 1. Press the [COMBI] button to make it light. setting button. Lit * The jack operates as an input jack. (EXTERNAL MIXING in your DAW. mode) the BEAT FX, press the [BFX] button to make The MX-1 synchronizes to the MIDI clock of the Press the [BFX] * The sound of hardware connected to the MX-1 NiDi (*) it light. The button of the MASTER FX type that’s used by the USB audio is not mixed; the sound adjusted by the [GAIN] device connected to the MIDI IN connector. pattern will light. frequency button and turn the 44.1, 48, 96 Specifies the sampling rate (kHz). (Default: 96) The MX-1 synchronizes to the MIDI clock of the [VALUE] knob button is sent to the computer. USB1–4 (*) 2. While holding down the button of the MASTER FX type Specifies the MIDI transmit/receive channel. The Press the [PAN] device connected to the USB HOST ports. Press the [SHUFFLE] OFF, C1–C16 display indicates the channel. (Default: 15) LED demo button and turn the OFF, 1–30 Specifies the time (minutes) until the LED demo is The MX-1 synchronizes to the MIDI clock that you want to assign, press pads [1]–[16] to select the MIDI channel button and turn the MIDI messages of all channels are received. The [VALUE] knob shown. (Default: 5 min) PC (*) that’s specified by the DAW running on the 4. On the channel for which you want to make BEAT FX steps on which to apply MASTER FX. [TEMPO] knob ONni(Omni) MIDI transmit channel will be 15. Pad Press the [AUX] Specifies the pad color scheme for each function. computer connected to the USB (O) port. settings, press the [SELECT] button to make it light. The pads to which MASTER FX applies are lit. If you’ve recalled a scene memory and the physical coloration button and turn the CL1–6 (Default: CL 1) (*) If there is no MIDI clock input, the MX-1 is the MIDI clock &”Mixer Section: [SELECT] button” * When you edit the settings, the pattern is overwritten Unlit (Jump) * position of a fader differs from the value that was System [VALUE] knob automatically. Press the [GAIN] master. 5. Hold down the CHANNEL SETTING [BFX] button and LEVEL fader recalled, operating that fader causes the value to Version button --- Displays the MX-1’s software version. jump immediately to the fader position. 3. Press the [SYNC] button to confirm the clock master. use pads [1]–[16] to specify the last step (the number of mode Press the Pad [1] If you’ve recalled a scene memory and the physical 3. Press the [START/STOP] button to save the settings. The display changes from blinking to lit. steps). Lit (Pass through) position of a fader differs from the value that was * The steps loop at the pad that you specify as the last recalled, fader movement is ignored until the fader The settings are saved, and the MX-1 restarts. 4. Press the [SYNC] button to make it go dark. step. passes through the recalled value. If “INT” is selected as the clock master, use the [TEMPO] Output the sound before it is adjusted by the knob and [FINE] knob or the [TAP] button to specify the AUX SEND Press the Pad [2] Unlit * [LEVEL] fader (pre-fader send). tempo. If a different clock master is selected, the MX-1 rooting Lit Output the sound after it is adjusted by the [LEVEL] synchronizes to the tempo of the connected device. fader (post-fader send).