Сплит-система TOSHIBA RAS-07EKV-EE / RAS-07EAV-EE. Инструкция на русском языке

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
ENGLISH
PУССКИЙ
Кондиционер (сплит-система)
для бытового использования
Внутренний блок
RAS-07, 10, 13, 16EKV
Наружный блок
RAS-07, 10, 13, 16EAV
1110255116
1110255116_EN.indd   1                                                                     2/13/13   2:47 PM

PRECAUTIONS FOR SAFETY                       3   AIRFLOW DIRECTION
?  Do not install, repair, open or remove the cover. It may
expose you to dangerous voltages. Ask the dealer or the
specialist to do this.               1   Press   FIX   : Move the louver in
0      ?  Turning off the power supply will not prevent potential   the desired vertical direction.
electric shock.
DANGER   ?  The appliance shall be installed in accordance with
national wiring regulation.
?  Means for disconnection from the supply having a
contact separation of at least 3 mm in all poles must be   Press   SWING   : Swing the air
incorporated in the ?xed wiring.     2   automatically and press again to
?  Do not expose your body directly to cool air for a long   stop.
time.
?  Do not insert your ?nger or any article into the air inlet/
outlet.                                  For horizontal direction, adjust
?  When an abnormality (burning smell, etc.) occurs, stop   3  manually.
the air conditioner and disconnect the power supply or
turn off the breaker.
?  This appliance is not intended for use by persons   Note:
0        (including children) with reduced physical, sensory or   ?  Do not move the louver manually by others.
mental capabilities, or lack of experience and knowledge,
?  The louver may automation positioning by some operation mode.
WARNING     unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
?  Children should be supervised to ensure that they do not
play with the appliance.           4    REMOTE CONTROL
?  Do not use any refrigerant different from the one speci?ed
for complement or replacement. Otherwise, abnormally   1 Infrared signal emitter  1
high pressure may be generated in the refrigeration   2 Start/Stop button
cycle, which may result in a failure or explosion of the
product or an injury to your body.  3 Mode select button (MODE)
4 Temperature button (TEMP)
?  Do not wash the unit with water. It may cause an electric
shock.                              5 Fan speed button (FAN)
?  Do not use this air conditioner for other purposes such as   6 Swing louver button (SWING)  3  4
preserving food, breeding animal, etc.  7 Set louver button (FIX)  2
?  Do not step or put anything on the indoor/outdoor unit. It   8 Off timer button (OFF)  7  6
may cause an injury or damage the unit.  9 High power button (Hi-POWER)  9  5
?  Do not touch aluminium ?n because it may cause an   ! Economy button (ECO)  8  !
injury.
0      ?  Before cleaning the unit, turn off the main switch or the   " Clear button (CLEAR)  #  "
circuit breaker.
CAUTION  ?  When the unit won’t be used for a long time, turn off the   # Check button (CHECK)
main switch or the circuit breaker.
?  It is recommended that maintenance be performed by
a specialist when the unit has been operated for a long
time.
?  The manufacturer shall not assume any liability for the   5  AUTOMATIC OPERATION
damage caused by not observing the description of this
manual.
To automatically select cooling, heating, or fan only operation
1.  Press   MODE   : Select A.
1  INDOOR UNIT DISPLAY                          2.  Press    : Set the desired temperature.
3. Press   FAN   : Select AUTO, LOW  , LOW+   , MED   ,
MED+   , or HIGH   .
1 TIMER (Yellow)
2 OPERATION (Green)
3 RESET button                      COOLING / HEATING / FAN ONLY
6
OPERATION
1. Press   MODE   : Select Cool   , Heat   , or Fan only   .
2. Press    : Set the desired temperature.
Cooling: Min. 17°C, Heating: Max. 30°C, Fan Only:
No temperature indication
2  PREPARATION BEFORE USE                       3.  Press   FAN   : Select AUTO, LOW  , LOW+   , MED   ,
MED+   , or HIGH   .
Preparing Filters
1.  Open the air inlet grille and remove the air ?lters.
2.  Attach the ?lters. (see detail in the accessory   7  DRY OPERATION
sheet).
Loading Batteries (when use wireless operation.)  For dehumidi?cation, a moderate cooling performance is controlled
1.   Remove the slide cover.                 automatically.
2.  Insert 2 new batteries (AAA type) following the (+)   1. Press   MODE   : Select Dry   .
and (–) positions.
Remote Control Reset                           2. Press    : Set the desired temperature.
1.  Remove the batteries.
2. Press    .
3.  Insert the batteries.
8  Hi-POWER OPERATION
To automatically control room temperature and air?ow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press   Hi POWER  : Start and stop the operation.
2/13/13   2:48 PM
1110255116_EN.indd   2                                                                     2/13/13   2:48 PM
1110255116_EN.indd   2

9  ECO OPERATION                              15  OPERATION AND PERFORMANCE
1.  Three-minute protection feature: To prevent the unit from being
To automatically control room to save energy (except in DRY and FAN ONLY
mode)                                            activated for 3 minutes when suddenly restarted or switched to ON.
2.  Preheating operation: Warm up the unit for 5 minutes before the
Press     : Start and stop the operation.       heating operation starts.
Note: Cooling operation; the set temperature will increase automatically 1   3.  Warm air control: When the room temperature reaches the set
degree/hour for 2 hours (maximum 2 degrees increase). For heating   temperature, the fan speed is automatically reduced and the outdoor
operation the set temperature will decrease.  unit will stop.
4.  Automatic defrosting: Fans will stop during defrost operation.
5.  Heating capacity: Heat is absorbed from outdoors and released into
the room. When the outdoor temperature is too low, use another
recommended heating apparatus in combination with the air
10  TEMPORARY OPERATION                           conditioner.                           EN
6.  Consideration for accumulated snow: Select the position for outdoor
In case of the misplaced or discharged remote control  unit where it will not be subjected to snow drifts, accumulation of   ES
?  Pressing the RESET button, the unit can start   leaves or other seasonal debris.
or stop without using the remote control.   7.  Some minor cracking sound may occur when unit operating. This is
?  Operation mode is set on AUTOMATIC           normal because the cracking sound may be caused by expansion/
operation, preset temperature is 25°C and fan   contraction of plastic.              FR
operation is automatic speed.                  Note: Item 2 to 6 for Heating model
Air conditioner operating conditions     PT
Temp.
Outdoor Temperature  Room Temperature
Operation                               RU
11  TIMER OPERATION                              Heating        –15°C ~ 24°C  Less than 28°C
Cooling        –10°C ~ 46°C  21°C ~ 32°C
Set the timer when the air conditioner is operating.  Dry      –10°C ~ 46°C  17°C ~ 32°C  TR
Setting the OFF timer
1  Press   OFF   for enter OFF timer setting.  16  TROUBLESHOOTING (CHECK POINT)
The unit does not operate.  Cooling or Heating is abnormally low.
2                                            ?  The power main switch is   ?  The ?lters are blocked with dust.
Press     for select desired OFF timer. (0.5 - 12 hrs)
turned off.      ?  The temperature has been set
?  The circuit breaker is   improperly.
3  Press   OFF   for set OFF timer.           activated to cut off the power   ?  The windows or doors are opened.
supply.
?  The air inlet or outlet of the outdoor
?  Stoppage of electric current  unit is blocked.
?  ON timer is set.  ?  The fan speed is too low.
4  Press   OFF   again for cancel OFF timer.                   ?  The operation mode is FAN or DRY.
17  REMOTE CONTROL A-B SELECTION
12  AUTO RESTART OPERATION
To separate using of remote control for each indoor unit in case of 2 air
conditioner are installed nearly.
To automatically restart the air conditioner after the power failure (Power of
the unit must be on.)                         Remote Control B Setup.
Setting                                        1.  Press RESET button on the indoor unit to turn the air conditioner ON.
1.  Press and hold the RESET button on the indoor unit for 3 seconds to   2.  Point the remote control at the indoor unit.
set the operation. (3 beep sound and OPERATION lamp blink 5 time/  3.  Push and hold    button on the Remote Control by the tip of the
sec for 5 seconds)                            pencil. “00” will be shown on the display. (Picture 1)
2.  Press and hold the RESET button on the indoor unit for 3 seconds to
cancel the operation. (3 beep sound but OPERATION lamp does not   4.  Press   MODE   during pushing   . “B” will show on the display and
blink)                                        “00” will disappear and the air conditioner will turn OFF. The Remote
•  In case of ON timer or OFF timer are set, AUTO RESTART   Control B is memorized. (Picture 2)
OPERATION does not activate.              Note: 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
13  MAINTENANCE
0 Firstly, turn off the circuit breaker.
Indoor Unit and Remote Control
?  Clean the indoor unit and the remote control with a wet cloth when   1  2
needed.
?  No benzine, thinner, polishing powder or chemically-treated duster.
SELF CLEANING OPERATION
14
(COOL AND DRY OPERATION ONLY)
To protect bad smell caused by the humidity in the indoor unit.
1. If the    button is pressed once during “Cool” or “Dry” mode,
the fan will continue to run for other 30 minutes, then it will turn off
automatically. This will reduce the moisture in the indoor unit.
2.  To stop the unit immediately, press the    more 2 times
within 30 seconds.
2/13/13   2:48 PM
1110255116_EN.indd   3                                                                     2/13/13   2:48 PM
1110255116_EN.indd   3