Ударная дрель RYOBI RPD500-G (3001832). Инструкция на русском языке

ORIGINAL INSTRUCTIONS                EN
TRADUCTION DES INSTRUCTIONS ORIGINALES  FR
UBERSETZUNG DER ORIGINALANLEITUNG    DE
TRADUCCION DE LAS INSTRUCCIONES ORIGINALES  ES
TRADUZIONE DELLE ISTRUZIONI ORIGINALI  IT
VERTALING VAN DE ORIGINELE INSTRUCTIES  NL
TRADUCAO DAS INSTRUCOES ORIGINAIS    PT
OVERS?TTELSE AF DE ORIGINALE INSTRUKTIONER  DA
RPD500                      OVERSATTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA  SV
ALKUPERAISTEN OHJEIDEN SUOMENNOS     FI
OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE  NO
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ           RU
TLUMACZENIE INSTRUKCJI ORYGINALNEJ   PL
PREKLAD ORIGINALNICH POKYNU          CS
AZ EREDETI UTMUTATO FORDITASA        HU
TRADUCEREA INSTRUCTIUNILOR ORIGINALE  RO
TULKOTS NO ORIGINALAS INSTRUKCIJAS   LV
ORIGINALIU INSTRUKCIJU VERTIMAS      LT
ORIGINAALJUHENDI TOLGE               ET
PRIJEVOD ORIGINALNIH UPUTA           HR
PREVOD ORIGINALNIH NAVODIL           SL
PREKLAD ORIGINALNYCH POKYNOV         SK
????????? ??? ?????????? ???????     EL
ORIJINAL TALIMATLARIN TERCUMESI      TR

English     EN
FR
DE
ES
¦  Electric tools used on fiberglass material, wallboard,
SPECIAL SAFETY RULES                                                        IT
spackling compounds, or plaster are subject to
¦  Wear ear protectors when impact drilling. Exposure   accelerated wear and possible premature failure   NL
to noise can cause hearing loss.       because the fiberglass chips and grindings are highly   PT
abrasive to bearings, brushes, commutators, etc.   DA
¦  Use auxiliary handle(s), if supplied with the tool.   Consequently, we do not recommend using this tool for
Loss of control can cause personal injury.  extended work on these types of materials. However, if   SV
¦  Hold power tool by insulated gripping surfaces,   you do work with any of these materials, it is extremely   FI
when performing an operation where the cutting   important to clean the product using compressed air.  NO
accessory may contact hidden wiring or its own                            RU
cord. Cutting accessory contacting a “live” wire may       WARNING        PL
make exposed metal parts of the power tool “live” and                     CS
could give the operator an electric shock.  Always wear safety goggles or safety glasses with side   HU
¦  Wear safety goggles to protect your eyes from flying   shields during power tool operation or when blowing   RO
dust. If operation is dusty, also wear a dust mask.
particles and splinters.
LV
¦  If the power supply cord is damaged, it must be replaced   LT
INTENDED USE                             only by the manufacturer or by an authorized service   ET
¦  Drilling and screw driving in all types of wood.  center to avoid risk. Contact authorized service center.
HR
¦  Drilling in metals: steel, brass, aluminum sheets,   LUBRICATION      SL
stainless steel and pipe (do not use impact drilling on                   SK
these materials).                   All of the bearings in the product are lubricated with a
suf? cient amount of high grade lubricant for the life span of   EL
¦  Drilling in masonry: stone and masonry (use impact   the product under normal operating conditions. Therefore,   TR
drilling), wall tiles (use ordinary drilling first, then impact   no further lubrication is required.
drilling).
Do not use this product in any other way other than those   ENVIRONMENTAL PROTECTION
stated for intended use.
Recycle raw materials instead of disposing
MAINTENANCE                                  of as waste. The machine, accessories and
packaging should be sorted for environmental-
friendly recycling.
WARNING
The product should never be connected to a power supply   SYMBOLS
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product will prevent   Safety Alert
accidental starting that could cause serious injury.
Class II, double insulated
WARNING
When servicing use only identical Ryobi replacement   Wood
parts. Use of any other parts may create a hazard or
cause product damage.                        Metal
¦  Avoid using solvents when cleaning plastic parts. Most   Masonry
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.    Impact
WARNING                      Chuck
Do not at any time let brake ? uids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact   CE conformity
with plastic parts. They contain chemicals that can
damage, weaken or destroy plastic.
1

English
GOST-R conformity
Please read the instructions carefully before
starting the machine.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
local authority or retailer for recycling advice.
2