Пила торцовочная RYOBI EMS1122LHG. Инструкция на русском языке

ORIGINAL INSTRUCTIONS                EN
TRADUCTION DES INSTRUCTIONS ORIGINALES  FR
UBERSETZUNG DER ORIGINALANLEITUNG    DE
TRADUCCION DE LAS INSTRUCCIONES ORIGINALES  ES
TRADUZIONE DELLE ISTRUZIONI ORIGINALI  IT
VERTALING VAN DE ORIGINELE INSTRUCTIES  NL
TRADUCAO DAS INSTRUCOES ORIGINAIS    PT
OVERS?TTELSE AF DE ORIGINALE INSTRUKTIONER  DA
EMS1122LHG                      OVERSATTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA  SV
ALKUPERAISTEN OHJEIDEN SUOMENNOS     FI
OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE  NO
ПЕРЕВОД ОРИГИНАЛЬНЫХ ИНСТРУКЦИЙ      RU
TLUMACZENIE INSTRUKCJI ORYGINALNEJ   PL
PREKLAD ORIGINALNICH POKYNU          CS
AZ EREDETI UTMUTATO FORDITASA        HU
TRADUCEREA INSTRUCTIUNILOR ORIGINALE  RO
TULKOTS NO ORIGINALAS INSTRUKCIJAS   LV
ORIGINALIU INSTRUKCIJU VERTIMAS      LT
ORIGINAALJUHENDI TOLGE               ET
PRIJEVOD ORIGINALNIH UPUTA           HR
PREVOD ORIGINALNIH NAVODIL           SL
PREKLAD ORIGINALNYCH POKYNOV         SK
????????? ??? ?????????? ???????     EL
ORIJINAL TALIMATLARIN TERCUMESI      TR

English     EN
FR
DE
ES
GENERAL SAFETY WARNINGS                  ¦  Disconnect tools. When not in use, before servicing   IT
and when changing accessories such as blades, bits   NL
and cutters, disconnect tools from the power supply.
WARNING                  ¦  Remove adjusting  keys and  wrenches.  Form the   PT
When using electric tools, basic safety precautions   habit  of checking  to see that keys and adjusting   DA
should  always  be  followed  to  reduce  the  risk  of  fire,   wrenches are removed from the tool before turning it   SV
electric shock and personal  injury.  Read  all these   on.                FI
instructions before attempting to operate this product     ¦  Avoid unintentional starting. Ensure switch is in “off”   NO
and save these instructions.            position when plugging in.         RU
¦  Use outdoor extension leads. When the tool is used   PL
¦  Keep work area clear. Cluttered areas and benches   outdoors, use only extension cords intended for outdoor   CS
invite injuries.                       use and so marked.                 HU
¦  Consider work  area environment. Do not expose     ¦  Stay alert.  Watch  what you are doing, use common   RO
tools to rain. Do not use tools in damp or wet locations.   sense and do not operate the tool when you are tired.
Keep work area well lit. Do not use tools in the presence     ¦  Check damaged parts. Before further use of tool, it   LV
of flammable liquids or gases.         should  be carefully  checked  to determine  that it will   LT
¦  Guard against electric shock. Avoid body contact with   operate properly and perform its intended function.   ET
earthed or grounded  surfaces (e.g.,  pipes,  radiators,   Check for alignment of moving parts, binding of moving   HR
ranges, refrigerators).                parts, breakage of parts, mounting and any other   SL
conditions  that may affect  its operation. A guard or
¦  Keep other persons away. Do not let persons,   other part that is damaged should be properly repaired   SK
especially children, be involved in the work, touch the   or replaced by an authorized service centre unless   EL
tool or the extension cord, and keep them away from   otherwise indicated in this  instruction manual. Have
the work area.                         defective switches replaced by  an authorized service   TR
¦  Store idle tools. When not in use, tools should  be   centre. Do not use the tool if the switch does not turn
stored in a dry locked-up place, out of reach of children.  it on and off.
¦  Do not force the tool. It will do the job better and safer     ¦  Warning. The use of any accessory  or attachment
at the rate for which it was intended.  other than the one recommended  in this instruction
¦  Use the right tool. Do not force small tools to do the   manual may present a risk of personal injury.
job of a heavy duty tool. Do not use tools for purposes     ¦  Have your tool repaired by a qualified person. This
not intended, for example, do not use circular saws to   electric  tool complies  with the relevant  safety rules.
cut tree limbs or logs.                Repairs should only be carried out by qualified persons
¦  Dress  properly. Do not wear loose clothing  or   using original spare parts otherwise this may result in
jewellery,  they can be caught  in moving  parts. Non-  considerable danger to the user.
skid footwear is recommended when working outdoors.
Wear protective hair covering to contain long hair.  SPECIAL SAFETY RULES
¦  Use protective equipment. Use safety glasses. Use     ¦  Wear ear protectors. Exposure to noise can cause
face or dust mask if working operations create dust.  hearing loss.
¦  Connect dust extraction equipment. If  the tool is     ¦  Appliances used at many different locations including
provided  for the connection  of dust extraction and   open air must  be connected via a  current surge
collecting equipment, ensure these are connected and   preventing switch.
properly used.                         ¦  Always wear goggles  when  using  the machine.  It is
¦  Do not abuse the cord. Never yank the cord to   recommended  to wear gloves, sturdy non slipping
disconnect it from the socket. Keep the cord away from   shoes and apron.
heat, oil and sharp edges.             ¦  Always disconnect the plug from the socket before
¦  Secure work. Where possible, use clamps or a vice to   carrying out any work on the machine.
hold the work. It is safer than using your hand.    ¦  Only plug-in when machine is switched off.
¦  Do not overreach. Keep proper footing and balance     ¦  Keep mains lead  clear from working  range  of the
at all times.                          machine. Always lead the cable away behind you.
¦  Maintain  tools  with  care.  Keep cutting tools sharp     ¦  Sawdust and splinters must not be removed while the
and clean for better and safer performance. Follow   machine is running.
instruction for lubricating  and changing  accessories.
Inspect tool cords periodically  and  if damaged,  have     ¦  Never reach into the danger area of the plane when it
them repaired by an authorized service facility. Inspect   is running.
extension cords periodically  and replace if  damaged.     ¦  Before use check machine, cable, and plug for any
Keep handles dry, clean and free from oil and grease.  damages or  material fatigue. Repairs should only be
1

English
carried out by authorised service agents.  shields  during  power  tool operation  or when  blowing
¦  Always use the protective shields on the machine.  dust. If operation is dusty, also wear a dust mask.
¦  Do not clamp the protective swing guard.    ¦  Any repairs must only be carried out by the laser
manufacturer or authorized service agent.
¦  Do not use saw blades which are damaged or deformed.     ¦  Do not replace the laser with a different type.
¦  Replace the table insert when worn.
¦  Do not use saw blades not corresponding to the key     ¦  Always use blades with correct  size and shape of
arbour holes. Blades that do not match the mounting
data given in these instructions for use.  hardware of the saw will run eccentrically, causing loss
¦  The protective  cover should  only  open  when  the   of control.
machine is lowered to the workpiece.    ¦  Use  only  blades  specified  in  this manual, complying
¦  Do not use saw blades made of high-speed steel.  with EN 847-1.
¦  Any  faults with the  machine, including  any related to
the safeguard or the saw blades, must be reported to   INTENDED USE
the persons in charge of safety as soon as the faults     ¦  The mitre saw can be used for  sawing solid wood,
are discovered.                        bonded wood, glued veneer, materials similar to wood,
¦  It is necessary to select a saw blade which is suitable   and plastics.
for the material being cut.            ¦  Do not use this product in any other way as stated for
¦  Never use the mitre saw to cut materials  other than   normal use.
those specified in the instruction manual.
¦  The handle  lock must always  be engaged  when   LASER SAFETY
transporting the mitre saw.
¦  Only use the saw with guards in good working  order     ¦  Do not stare into beam during operation.
and properly maintained, and in position.    ¦  Do not project the laser beam directly into the eyes of
others. Serious eye injury could result.
¦  Keep the floor area free of loose material e.g., chips
and cut-offs.                          ¦  Do not  place  the  laser  in a  position that  may  cause
anyone to stare into the laser beam intentionally  or
¦  Only use saw blades which  have been properly   unintentionally.
sharpened. It  is essential to  adhere to  the maximum
speed specified on the saw blade.      ¦  Do not use optical tools to view the laser beam.
¦  Do not  use any flanges other than those supplied  or     ¦  Do not operate the laser around  children  or allow
indicated in the instruction manual to secure the saw   children to operate the laser.
blade.                                 ¦  Do not attempt to repair the laser device by yourself.
¦  Refrain from removing any cut-offs or other parts of the     ¦  Do not attempt to change any parts of the laser device
workpiece from the cutting area whilst the machine is   by yourself.
running and the saw head is not in the rest position.    ¦  Any repairs must only be carried out by the laser
¦  Ensure that the machine is always stable and secure   manufacturer or authorized service agent.
(e.g., fixed to a bench).              ¦  Do not replace the laser with a different type.
¦  Long workpieces must be adequately supported.
¦  Do not use cracked or distorted saw blades.  ENVIRONMENTAL PROTECTION
¦  Before using  the tool please  read the instructions. If
possible have the tool demonstrated.        Recycle raw materials instead of disposing
¦  The dust produced when using this tool may be harmful   of as waste.  The machine,  accessories
and packaging  should  be sorted for
to health. Use  a dust absorption  system and  wear  a   environmental-friendly recycling.
suitable dust protection mask. Remove deposited dust
thoroughly, e.g., with a vacuum cleaner.
¦  Stock having a round or irregular cross section (such   SYMBOL
as firewood) must not be cut, as it cannot be securely
held during cutting. When sawing thin stock layered on
edge, a suitable auxiliary fence must be used for firm   Safety alert
support.
¦  Use  of controls  or adjustments  or performance  of
procedures other than those specified herein may result   CE Conformity
in hazardous radiation exposure.
¦  Do not stare directly at the laser beam.
¦  Always wear safety goggles or safety glasses with side
2