Дрель-миксер MAKITA UT1401. Инструкция на русском языке

GB            Hand-Held Mixer                 Original Instructions
S             Handhallen Mixer                Originalinstruktioner
N             Handholdt mikser                Originalinstruksjoner
FIN           Kasisekoitin                    Valmistajan kayttoohjeet
LV            Rokas maisitajs                 Originala lietosanas instrukcija
EE            Segur                           Originaaljuhendi tolge
LT            Rankinis maisytuvas             Instrukcijos
RUS           Ручной смеситель                Оригинальная инструкция
UT 1401
UT 1600

ENGLISH
Technical data
UT 1401                UT 1600
Rated voltage:             110 V ~    230 V ~     1           230 V ~
110 V ~10 V ~
Power input:               1050 W     1300 W      1500 W00 W   1800 W
I   0–410 rpm  0–400 rpm  0–450 rpm 0 rpm  0–440 rpm
No load speed:
II   0–740 rpm  0–730 rpm  0–1000 rpm0 rpm  0–970 rpm
Frequency:                                   50 Hz
Tool holder:                                  M 14
Safety class:                                  II
Safety degree:                               IP 20
Weight according to EPTA         5,5 kg                 7,1 kg
Procedure 01/2003:
This manual shall be subject to modification without prior notice in the course of his manual shall be subject to modification without prior notice in the course of
T
developments and technical progress.
Note: The technical data may differ depending on the country.
Symbols
The following symbols are used for the equipment. It is important to know their he following symbols are used for the equipment. It is important to know their
T
meaning before you use the tool.
Read instructions
Work with concentration and care.
K
Keep your workplace clean and avoid hazardous situations.eep your workplace clean and avoid hazardous situations.
Precautions shall be taken to protect operators.
Double protective insulation
Intended use
The mixer UT 1401 is used to stir and mix prefab plaster, gypsum, lime, concrete prefab plaster, gypsum, lime, concrete
and other building materials of medium and high viscosity in batches up to 50 kg. nd other building materials of medium and high viscosity in batches up to 50 kg.
a
T
The diameter of the stirrers that are used should not exceed 140mm.he diameter of the stirrers that are used should not exceed 140mm.
The mixer UT 1600 is designed for use in mixing material of high viscosity, such is designed for use in mixing material of high viscosity, such
as prefab mortar and plaster, cement, lime, concrete, quartz--filled epoxy resins,
screed, pastes, sealing compounds as well as gypsum and granulates in batches creed, pastes, sealing compounds as well as gypsum and granulates in batches
s
up  to  80  kg.  The  diameter  of  the  mixing  agitators  must  not  exceed  a  value  of mixing  agitators  must  not  exceed  a  value  of
180mm.
The user shall be responsible for damages caused by inappropriate use.he user shall be responsible for damages caused by inappropriate use.
T
G
Generally  accepted  accident  prevention  regulations  and  the  safety  instructions enerally  accepted  accident  prevention  regulations  and  the  safety  instructions
enclosed shall be observed.

Power supply
The machine shall only be connected to the voltage stated on the type plate and it
only  works  with  single-phase  AC  voltage.  It  is  provided  with  double  protective
insulation according to European standards and thus, it may be also connected to
sockets without ground cable.
Do only use extension cables with sufficient cross section. A cross section that is
too small may lead to excessive loss of power and overheating of the tool and the
cable.
Safety Instructions
WARNING!
Read all safety warnings and all instructions.
Failure  to  follow  the  warnings  and  instructions  may  result  in  electric  shock, fire
and/or serious injury.
Save all warnings and instructions for future reference.
ADDITIONAL SAFETY RULES FOR THIS MACHINE:
1.  If the connecting cable  is  damaged or cut  during  work, do not touch it and
immediately disconnect the power plug. In any case, do not work with the tool
if the connecting cable is damaged.
2.  The  tool  should  not  be  humid  and  it  should  not  be  operated  in  a  humid
environment.
3.  Do not use the tool to mix explosive or easily inflammable substances and do
not use it in areas close to these substances.
4.  Do not use the cable to carry the tool.
5.  Do always  inspect the tool, the cable  and the plug before using  it. Repairs
shall only be carried out by an expert. The plug shall only be connected to the
socket if the tool is switched off.
6.  Do only operate the tool outdoor with a residual current circuit breaker with a
maximum of 30 mA.
7.  Do not leave the hand-held mixer running unattended.
8.  Do disconnect the power plug and check if the hand-held mixer is switched off
when  it  is  left  unattended,  e.g.  during  assembly  and  disassembly  work,
voltage drop, insertion and/or assembly of accessories.
9.  Do switch off the tool if it stops to operate due to whatever cause in order to
avoid a sudden start of operation when it is unattended.
10. Do always lead the cable away behind the tool.
11. Do not use the tool if a part of the housing and/or the switch, cable or plug is
damaged.
12. Power tools shall be inspected by an expert regularly.
13. Do not touch rotating parts.
14. Be careful with long hair. Do not wear loose clothing.
15. Do not manipulate the tool.
16. Do ensure that the handle bars are dry, clean and free from oil and grease.
17. When the tool is operated manually, make sure that you always hold the tool
with both hands and  you  stand in a firm position. Be aware of the reaction
moment of the tool.