Полировальная шлифмашина MAKITA PV7000C. Инструкция на русском языке

GB  Electronic Polisher                INSTRUCTION MANUAL
S  Elektronisk poleringsmaskin        BRUKSANVISNING
N  Elektronisk polerer                BRUKSANVISNING
FIN  Sahkokiillotuskone                KAYTTOOHJE
LV  Elektroniska pulejama slipmasina  LIETOSANAS    INSTRUKCIJA
LT  Elektrinis poliravimo irankis     NAUDOJIMO INSTRUKCIJA
EE  Elektrooniline poleermasin         KASUTUSJUHEND
RUS  Электронное полировальное устройство  РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
PV7000C
1

2                        1
1
1
2
1               003407  2                003408   3               003444
1
1                                       2
2
1                                                       3
2
4               004419   5               004420   6               004421
1
1                         1     3
2
2
2
7               004422   8               004424  9                004425
15
10              004426  11               003479   12              003480
1
2
1
13              001145   14              003423
2

ENGLISH (Original instructions)
Explanation of general view
1-1. Switch trigger      5-2. Side grip           8-2. Lock nut
1-2. Lock button         6-1. Backing pad         8-3. Rubber pad
2-1. Speed adjusting dial   6-2. Spindle          9-1. Lock nut wrench
3-1. High-Low speed setting button   6-3. Wrench   9-2. Wrench
4-1. Cover               7-1. Sponge pad          13-1. Limit mark
4-2. Side grip           7-2. Pad                 14-1. Brush holder cap
5-1. Cover               8-1. Wool bonnet         14-2. Screwdriver
SPECIFICATIONS
Model                               PV7000C
Max capacities   Sponge pad/ Wool bonnet       180 mm
Spindle thread                         M14
-1
Rated speed (n)/No load speed (n 0 )      600 - 2,000 min
Overall length                        210 mm
Net weight                            2.1 kg
Safety class                           /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
ENE051-1                              ENG901-1
Intended use                          •   The declared vibration emission value has been
The tool is intended for polishing,  smoothing before   measured in accordance with the standard  test
painting, finishing surfaces, and removing rust and paint.   method and may be used for comparing one tool
ENF002-1   with another.
Power supply                          •   The declared vibration emission value may also be
The tool should be connected only to a power supply of   used in a preliminary assessment of exposure.
the  same voltage  as indicated on the nameplate,  and
can only be operated on single-phase AC supply. They   WARNING:
are double-insulated in accordance with European   •   The vibration emission during actual use of  the
Standard and can, therefore, also be used from sockets   power tool  can  differ from the declared emission
without earth wire.                      value depending on the ways in which the tool is
ENG102-3
Noise                                    used.
The typical A-weighted noise level determined according   •   Be sure to identify safety measures to protect the
to EN60745:                              operator that  are  based on an  estimation  of
Sound pressure level (L pA) : 81 dB(A)   exposure in the actual conditions of use (taking
Sound power level (L WA) : 92 dB(A)   account of all parts of the operating cycle such as
Uncertainty (K) : 3 dB(A)             the times when the tool is switched off and when it
Wear ear protection           is running idle in addition to the trigger time).
ENG240-1
Vibration                                                          ENH101-13
The vibration  total value  (tri-axial vector  sum)   For European countries only
determined according to EN60745:     EC Declaration of Conformity
Work mode : polishing             We  Makita  Corporation  as  the  responsible
2
Vibration emission (a h,P) : 2.5 m/s  or less   manufacturer declare that the following  Makita
Uncertainty (K) : 1.5 m/s 2       machine(s):
If the  tool is used for other applications, the  vibration   Designation of Machine:
emission value may be different.     Electronic Polisher
Model No./ Type: PV7000C
are of series production and
Conforms to the following European Directives:
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
3