Отбойный молоток MAKITA HM1213C. Инструкция на русском языке

INSTRUCTION MANUAL
MANUEL D'INSTRUCTION
MANUAL DE INSTRUCCIONES
Demolition Hammer
Marteau de demolition
Martillo Domoledor
HM1213C
HM1203C
009939
DOUBLE INSULATION
DOUBLE ISOLATION
DOBLE AISLAMIENTO
1

ENGLISH
SPECIFICATIONS
Model                     HM1213C            HM1203C
Blows per minute                      950 - 1,900
Overall length                     576 mm (22-3/4")
Net weight               10.8 kg (23.6 lbs)   9.7 kg (21.4 lbs)
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
GEA008-1   increase the risk of electric shock.
8.   When operating a power tool outdoors, use an
General Power Tool Safety                extension cord suitable for outdoor use. Use of
Warnings                                 a cord suitable for outdoor use reduces the risk of
WARNING Read all safety  warnings and all   electric shock.
instructions. Failure  to  follow the warnings and   9.   If operating a power tool in a damp location is
instructions may result in  electric shock,  fire and/or   unavoidable, use a ground fault circuit
serious injury.                          interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Save all warnings and                Personal Safety
instructions for future reference.    10.  Stay alert, watch what you are doing and use
common sense when operating a power tool.
The  term "power  tool" in  the warnings refers  to your   Do not use a power tool while you are tired or
mains-operated (corded) power tool or battery-operated   under the  influence of drugs, alcohol or
(cordless) power tool.                   medication.  A  moment of inattention while
Work area safety                         operating power tools may result  in  serious
1.   Keep work area clean and well lit. Cluttered or   personal injury.
dark areas invite accidents.      11.  Use personal protective equipment.  Always
2.   Do not operate power tools  in explosive   wear eye protection. Protective equipment such
atmospheres, such as  in the presence of   as dust mask, non-skid safety shoes, hard hat, or
flammable liquids, gases or dust. Power tools   hearing protection used for appropriate conditions
create sparks which may ignite the dust or fumes.   will reduce personal injuries.
3.   Keep children and bystanders away  while   12.  Prevent unintentional starting. Ensure the
operating a power tool. Distractions can cause   switch is in the off-position before connecting
you to lose control.                 to power source and/or battery pack, picking
Electrical Safety                        up or  carrying the tool.  . Carrying power tools
4.   Power tool plugs must match the outlet. Never   with your finger on the switch or energising power
modify the plug in any  way. Do not use any   tools that have the switch on invites accidents.
adapter plugs with earthed (grounded) power   13.  Remove any adjusting key or  wrench before
tools. Unmodified plugs and matching outlets will   turning the power tool on. A wrench or a key left
reduce risk of electric shock.       attached to a rotating part of the power tool may
5.   Avoid body contact with earthed or grounded   result in personal injury.
surfaces such as pipes, radiators, ranges and   14.  Do not overreach. Keep proper footing and
refrigerators.  There is an increased risk of   balance at all times. This enables better control
electric shock if your body is earthed or grounded.   of the power tool in unexpected situations.
6.   Do not expose  power tools to rain or  wet   15.  Dress properly. Do not wear loose clothing or
conditions. Water  entering a  power tool  will   jewellery. Keep your hair, clothing, and gloves
increase the risk of electric shock.   away from moving parts. Loose  clothes,
7.   Do not abuse the cord. Never use the cord for   jewellery or long hair  can  be  caught in moving
carrying, pulling or unplugging the power tool.   parts.
Keep cord away from heat, oil, sharp edges or   16.  If devices are provided for the connection of
moving parts. Damaged or entangled cords   dust extraction and collection facilities,
2

ensure these are connected and properly used.   are caused by poorly maintained power tools.
Use  of dust collection can reduce  dust-related   22.  Keep cutting tools sharp and clean. Properly
hazards.                             maintained cutting tools with sharp cutting edges
Power tool use and care                  are less likely to bind and are easier to control.
17.  Do not force the power tool. Use the correct   23.  Use the power tool, accessories and tool bits
power tool for  your application. The  correct   etc. in  accordance  with these instructions,
power tool will do the job better and safer at the   taking  into account the  working  conditions
rate for which it was designed.      and the work to be performed. Use of the power
18.  Do not use the power tool if the switch does   tool for operations different from  those  intended
not turn it on and off. Any power tool that cannot   could result in a hazardous situation.
be controlled  with the switch  is dangerous  and   SERVICE
must be repaired.                 24.  Have your power tool serviced by a qualified
19.  Disconnect the plug from the power source   repair person using only identical replacement
and/or the battery  pack  from the  power tool   parts. This will ensure that the safety of the power
before making any adjustments, changing   tool is maintained.
accessories, or  storing power tools. Such   25.  Follow  instruction  for  lubricating  and
preventive safety measures reduce  the risk of   changing accessories.
starting the power tool accidentally.   26.  Keep handles dry, clean and free from oil and
20.  Store idle power tools out of the  reach of   grease.
children and do not allow persons unfamiliar   USE PROPER  EXTENSION CORD.  Make sure your
with the power  tool or these instructions to   extension  cord is  in good condition.  When using an
operate the power  tool. Power tools  are   extension cord,  be  sure  to use one  heavy enough to
dangerous in the hands of untrained users.   carry the current your product will draw. An undersized
21.  Maintain power tools. Check for misalignment   cord will cause a drop in line voltage resulting in loss of
or binding of moving parts, breakage of parts   power and overheating. Table 1 shows the correct size to
and any  other condition that  may  affect the   use depending on  cord length  and nameplate ampere
power tool’s operation. If damaged, have the   rating. If in doubt, use the next heavier gage. The smaller
power tool repaired before use. Many accidents   the gage number, the heavier the cord.
Table 1: Minimum gage for cord
Volts        Total length of cord in feet
Ampere Rating
120 V   25 ft.   50 ft.  100 ft.  150 ft.
More Than    Not More Than                    AWG
0              6                  18       16      16       14
6             10                  18       16      14       12
10             12                  16       16      14       12
12             16                  14       12    Not Recommended
000173
GEB004-5   the cutting accessory may contact hidden
wiring or  its own  cord. Cutting accessory
HAMMER SAFETY WARNINGS                   contacting a "live" wire may make exposed metal
DO NOT let comfort or familiarity  with product   parts of the power tool "live" and could give the
(gained from repeated use) replace strict adherence   operator an electric shock.
to safety rules for the subject product. If you use this   4.   Wear a hard hat (safety helmet), safety glasses
tool unsafely or incorrectly, you can suffer serious   and/or face shield.  Ordinary eye or sun
personal injury.                         glasses are NOT safety  glasses.  It is also
1.   Wear ear protectors. Exposure to  noise can   highly recommended that  you  wear a dust
cause hearing loss.                  mask and thickly padded gloves.
2.   Use auxiliary handle(s), if  supplied  with the   5.   Be sure the bit  is secured in place before
tool. Loss of control can cause personal injury.   operation.
3.   Hold power tool by insulated gripping   6.   Under normal operation, the tool is designed
surfaces, when performing an operation where   to produce vibration. The screws  can come
3