Машинка шлифовальная прямая MAKITA GD0602. Инструкция на русском языке

GB  Die Grinder                        INSTRUCTION MANUAL
UA  Прямощліфувальна машина            ІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ
PL  Szlifierka katowa                  INSTRUKCJA    OBSLUGI
RO  Polizor drept                      MANUAL DE INSTRUCTIUNI
DE  Geradschleifer                     BEDIENUNGSANLEITUNG
HU  Egyenescsiszolo                    HASZNALATI KEZIKONYV
SK  Raznicova bruska                   NAVOD NA OBSLUHU
CZ  Prima bruska                       NAVOD K OBSLUZE
GD0602
1

3
1
2
1
1                          009307   2                         009308
8 mm MAX.
3                          009309   4                         009310
1
5                          009311
2

ENGLISH (Original instructions)
Explanation of general view
1-1. Slide switch        2-2. Collet nut          5-1. Side handle
2-1. Wrench 13           2-3. Wrench 13
SPECIFICATIONS
Model                               GD0602
Max. collet capacity                    8 mm
Max. wheel point diameter                38 mm
-1
Rated speed (n)/No load speed (n 0 )       25000 min
Overall length                        264 mm
Net weight                            1.4 kg
Safety class                           /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
ENE050-1   •   Be sure to identify safety measures to protect the
Intended use                             operator that  are  based on an  estimation  of
The tool is intended for grinding  ferrous materials  or   exposure in the actual conditions of use (taking
deburring castings.                      account of all parts of the operating cycle such as
ENF002-1
Power supply                             the times when the tool is switched off and when it
The tool should be connected only to a power supply of   is running idle in addition to the trigger time).
the  same voltage  as indicated on the nameplate,  and             ENH101-13
can only be operated on single-phase AC supply. They   For European countries only
are double-insulated in accordance with European   EC Declaration of Conformity
Standard and can, therefore, also be used from sockets   We  Makita  Corporation  as  the  responsible
without earth wire.
ENG104-2   manufacturer declare that the following  Makita
Noise                                machine(s):
The typical A-weighted noise level determined according   Designation of Machine:
to EN60745:                          Die Grinder
Sound pressure level (L pA) : 75 dB(A)   Model No./ Type: GD0602
Uncertainty (K) : 3 dB(A)         are of series production and
The noise level under working may exceed 80 dB (A).   Conforms to the following European Directives:
Wear ear protection.           98/37/EC until 28th December 2009 and then with
ENG206-3   2006/42/EC from 29th December 2009
Vibration                            And are manufactured in accordance with the following
The vibration  total value  (tri-axial vector  sum)   standards or standardised documents:
determined according to EN60745:         EN60745
Work mode : surface grinding      The technical documentation is kept by our authorised
2
Vibration emission (a h,SG) : 2.5 m/s  or less   representative in Europe who is:
Uncertainty (K) : 1.5 m/s 2           Makita International Europe Ltd,
ENG901-1   Michigan, Drive, Tongwell,
•   The declared vibration emission value has been   Milton Keynes, MK15 8JD, England
measured in accordance with the standard  test
method and may be used for comparing one tool
30th January 2009
with another.
•   The declared vibration emission value may also be
used in a preliminary assessment of exposure.
000230       Tomoyasu Kato
WARNING:                                           Director
•   The vibration emission during actual use of  the   Makita Corporation
power tool  can  differ from the declared emission   3-11-8, Sumiyoshi-cho,
value depending on the ways in which the tool is   Anjo, Aichi, JAPAN
used.
3