На сайте 124169 инструкций общим размером 502.7 Гб , которые состоят из 6277380 страниц
Руководство пользователя FELISATTI APF200/1010E. Основные функции, характеристики и условия эксплуатации изложены на 24 страницах документа в pdf формате.
Доступно к просмотру 22 страницы. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.
Fig. 1 B C A D H E Fig. 2 G F I
TECHNICAL DATA Floor and wall sander APF200/1010E Input power W 1010 No-load speed rpm 800-1800 Maximum diameter of sandpaper sheet mm 200 Spindle thread ISO M14 Approx. weight (without acces.) Kg 2.9 The instructions contained in this manual must be strictly ? WARNING! Before each use, inspect the plug and followed, it should be carefully read and kept close at lead. Should they need replacing, have this done by an hand to use when carrying out maintenance on the official service centre. indicated parts. ? Always keep the mains lead clear of the working range If the machine is used carefully and normal maintenance of the machine. is carried out, it will work well for a long time. ? Only plug the machine in when it is switched off. The functions and use of the tool you have bought shall ? Always use the machine with the auxiliary handle be only those described in this manual. Any other use attached. of the tool is strictly forbidden. ? Hold the machine firmly in both hands and in a stable position. ILLUSTRATIONS ? Check that the stated disc speed is equal to or greater DESCRIPTION (See figures) than the polisher’s rated speed. A Start-up switch (Fig.1) ? Verify that the disc dimensions are compatible with the polisher. B Auxiliary handle (Fig.1) ? The abrasive discs should be handled and kept with C Spindle blocking button (Fig.1) the utmost care, in accordance with the manufacturer’s D Cap (Fig.1) instructions. E Brush (Fig.1) ? Protect the polisher from knocks, collisions and grease. F Interface (Fig.2) ? Check the disc carefully before use to make sure it is G Velcro plate (Fig.2) not damaged or cracked. Replace cracked or dam- H Dust output (Fig.1) aged discs immediately. ? Make sure the discs are fitted in accordance with the EQUIPMENT manufacturer’s instructions. - 1 auxiliary handle ? Check that the disc has been properly fitted and se- - 1 cap cured before using the machine. Start the machine - 1 brush with no load and run for 30 seconds in a safe position; - 1 Velcro plate if you notice serious vibration or any other defect stop - 1 interface the machine immediately. This may be a sign of incor- - Operating instructions rect fitting or a badly balanced disc. - Safety instructions ? Use only clamps or plates specified for this tool. Do not - Warranty use separate bushings or adapters to adapt grinding discs with large holes. SAFETY INSTRUCTIONS ? In machines designed to be used with accessories with ? See “Safety Instructions” manual, supplied with this threaded holes, check that the thread on the disc is instruction manual. long enough to take the length of the spindle. ? WARNING! Material containing asbestos must not be ? Beware of shavings that fly off. Hold the tool that so polished. Working with materials containing amian- that sparks fly away from you or other people and in- thus/asbestos and/or silica stones produces a dust, flammable materials. which is harmful to health. Protect yourself from inhal- ? When working on stone, use dust extraction equipment ing this dust, in compliance with current regulations on and wear a mask. accident prevention. ? In order for the job to be effective, you should select, ? For your personal safety, always connect the machine based on the material and surface finish, the appropri- to a mains supply protected by a differential and ther- ate size and abrasive. mal cutout switch, in accordance with regulations on ? Do not touch rotating polishing tools. low-voltage wiring sitemaps. ? WARNING! The disc will continue to rotate for a time ? Do not pierce the motor housing as this could damage after the machine is switched off. the double insulation (use adhesive labels). ? When working with the machine, always wear safety ? Check the work area with a metal detector for hidden goggles and ear protection. Other personal protection wires, gas and/or water pipes. equipment such as dust masks, gloves, helmet and ? Always unplug the machine before carrying out apron should be worn when necessary, along with work on it. non-slip safety footwear. When considering the need ? Always stop the machine by switching it off, not by to use a protective mask against the dust, this should unplugging it. also be for the possible harmful effects of the polished
material and paint or other surface coating. If in doubt, Start the machine by turning the switch A to position use safety equipment. "ON". To switch off, do the same in reverse. ? Make sure the vents are free when working with Constant electronic performance and speed adjustment dust. If they require cleaning, first unplug the ma- The built-in module enables soft start and for the rated chine, do not use metal objects and avoid damag- speed to be maintained practically constant until the ing internal parts. rated power is reached. ? WARNING: Certain types of dust produced by me- The electronic speed regulator enables the speed to chanical polishing, sawing, grinding and drilling, to- be set to different positions from 1 to 6. The most gether with other construction activities, contain chemical agents which are known to cause cancer, appropriate speed should be selected according to the part to be polished. congenital and other similar defects. Some examples of the chemical agents are given below: the lead in PRECAUTION: The speed regulator can only be turned lead-based paint, crystalline silica from bricks and to position 6 and then be returned to position 1. It must cement and other masonry products, and also arse- never be forced beyond 6 or 1, since this could cause nic and chromium from chemically treated wood. The damage to the machine. risk deriving from this type of exposure varies and WORKING INSTRUCTIONS depends on the frequency with which this type of work is carried out. In order to reduce exposure to Do not use the sander without the abrasive disk. these chemical agents: work in a well ventilated area To dry sand walls and work with approved safety equipment, such as face masks which are specially designed to filter out Turn on the sander. microscopic particles. Place the sander lightly on the work area. Apply only the pressure necessary to maintain the BRIEF DESCRIPTION abrasive disk flat against the work area. This polisher has been designed to polish all types of Maintain the movement of the sander while the disk is in construction and industrial surfaces. contact with the work area. Use constant and broad movements. BEFORE USING THIS TOOL Attention: do not let the spinning disk touch sharp Before using the tool, make sure the mains voltage is protrusions, screws, nails, etc., because they could correct: it must be the same as that on the specification cause damage. label. Machines with 230V can also be connected to a Use sandpaper discs which are suitable for the surface 220-V mains supply. to be worked and the required results. PRECAUTION: During polisher operation, the electri- FITTING SAFETY DEVICES cal cable should always be kept behind to prevent it WARNING! Always unplug the machine before carrying being trapped. out work on it. Use of the auxiliary handle is obligatory in order to ensure DUST EXTRACTION greater control and safety when handling the tool. WARNING! Always make sure that the tool is switched off and unplugged before fitting or removing any dust FITTING THE ACCESSORIES (DISCS AND WHEELS) extraction device. WARNING! For safety reasons, the machine should Dust extraction keeps the workplace clean, prevents always be unplugged from the mains before changing dust build-up in the air and facilitates waste elimination. the disc or wheel. Always wear safety goggles. These sanders are provided with a dust aspiration WARNING! Never press the blocking button when the output which adapts to a universal vacuum or any other machine is running. The shaft must have stopped com- dust aspiration device. pletely before the blocking button is pressed. CAUTION: Always use an aspiration extractor designed To assemble the Velcro plate, proceed in the following according to the guidelines applicable to dust emission. manner (Fig.1): The flexible hoses of conventional vacuum cleaners fit 1. Block the spindle (shaft), by pressing the blocking directly onto the dust extraction nozzle. button C. The aspirator should be suitable for the material being 2. With hexagonal key, unscrew screw I (Fig.2) and worked. remove the washer. A special aspirator must be employed in those cases 3. Position the Velcro plate. where dry harmful or carcinogenic dust is produced. 4. Replace the washer and screw on the screw with the help of the hexagonal key. ACCESSORIES 5. Once the disc is fitted, check that the blocking button Accessories and their corresponding order number can has returned to its original position due to movement be found in our catalogues. of the incorporated spring. MAINTENANCE AND CARE STARTING THE TOOL WARNING! Always unplug the machine before carrying WARNING! Check that the mains voltage is the same as out work on it. that in the machine’s specifications. - Inspect the tool: Using a worn out polishing or polish- Plug the machine in with the switch off. ing tool will reduce working efficiency.