Настенное крепление NEC Wall Mount PD02W T L L. Инструкция на английском языке

I N S T A L L A T I O N                             I N S T R U C T I O N S
MSA1U
MTA1U
LSA1U                                            LTA1U
FUSION MEDIUM AND LARGE
FLAT PANEL MOUNTS
MSA1U/MTA1U/LSA1U/LTA1U

MSA1U/MTA1U/LSA1U/LTA1U                                                          Installation Instructions
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and  WARNING: Never operate this mounting system if it is
subsidiaries (collectively "Milestone"), intend to make this  damaged. Return the mounting system to a service center for
manual accurate and complete. However, Milestone makes no  examination and repair.
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this  WARNING: Do not use this product outdoors.
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,  IMPORTANT ! : The MSA1U/MTA1U/LSA1U/LTA1U mounts
regarding the information contained herein. Milestone assumes  are designed to be mounted to:
no responsibility for accuracy, completeness or sufficiency of  •  a bare 8" concrete or 8"x8"x16" concrete block wall, or
the information contained in this document.               •  a 2" x 4" wood stud wall covered by drywall with
maximum thickness of 5/8":
•   MSA1U/MTA1U: Wood studs must be 16" on
Chief® is a registered trademark of Milestone AV Technologies.   center;
All rights reserved.                                         •   LSA1U/LTA1U: Wood studs may be 16" or 24" on
center.
--SAVE THESE INSTRUCTIONS--
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty!  It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment!  It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment!  It is the
installer’s responsibility to make sure the combined weight of
all components located on the MSA1U/MTA1U does not
exceed 125 lbs (56.7 kg), OR 200 lbs (90.7 kg) for the LSA1U/
LTA1U.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
2

Installation Instructions                                                 MSA1U/MTA1U/LSA1U/LTA1U
DIMENSIONS
MSA1U
6.00
152.4
RAILS CAN BE SLID LEFT OR RIGHT
FOR OFFSET
1.    MAXIMUM MOUNTING PATTERN IS 22.7" (576 mm) WITHOUT REVERSING UPRIGHTS  DIMENSIONS:       INCHES
2.    MAXIMUM MOUNTING PATTERN IS 25.3" (642 mm) WITH REVERSING UPRIGHTS
3.    FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK                     [MILLIMETERS]
ENGAGEMENT IS .75" (19 mm)
MTA1U
6.00
152.4
RAILS CAN BE SLID LEFT OR RIGHT
FOR OFFSET
1.    MAXIMUM MOUNTING PATTERN IS 22.25" (565 mm) WITHOUT REVERSING UPRIGHTS  DIMENSIONS:       INCHES
2.    MAXIMUM MOUNTING PATTERN IS 25.6" (650 mm) WITH REVERSING UPRIGHTS
3.    FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEMENT IS .75" (19 mm)                                                         [MILLIMETERS]
3