Радиочасы VITEK VT-3510 PK. Инструкция на русском языке

ENGLISH
1
19.09.2011   9:19:03
3510_2_IM.indd   1                                                    19.09.2011   9:19:03
3510_2_IM.indd   1

19.09.2011   9:19:05
3510_2_IM.indd   2
3510_2_IM.indd   2                                                    19.09.2011   9:19:05

ENGLISH
CLOCK RADIO                          the minutes) or to the right (to set the hours).
When the time has been set, move the RUN/
CONTROLS AND FUNCTIONS               ALM/TIME (5) selector back to RUN. The two
1.  Power cord                       blinking dots on the display (7) should stop
2.  FM antenna                       blinking.
3.  SNOOZE button
4.  Battery compartment              SETTING THE CURRENT TIME FOR THE
5.  RUN/ALM/TIME Clock function selector  PROJECTOR
6.  ON/AUTO/OFF Function selector    Attention! The current time shown on the dis-
7.  Lighted display                  play and that projected by the projector must
8.  Rotating function dial           be set separately.
9.  SLEEP button
10. Radio frequency tuning knob      Projector:
11. AM/FM Band selector              Set the projector selector (14) to the ON posi-
12. VOLUME/BUZZER knob               tion. Press and hold the T button (18); press
13. Projector                        the H (16) button to set the hours and the M
14. Projector On/Off button          (15) button to set the minutes. Switch the pro-
15. Minute setting button for projector  jector selector (14) to the OFF position to turn
16. Hour setting button for projector  the projector off.
17. Projector focus control
18. Time setting button for projector  Note: The time displayed by the projector on
the wall or ceiling can be easily seen in a dark
POWER                                room. The maximum projection distance is
1.  Connect the power cord to the outlet.   0.6 – 2.7 m. Use the focus control dial (17)
Make sure that the voltage indicated on the   to adjust the brightness and focus of the pro-
device matches the voltage in your home.  jected image.
2.  Place one 9 V battery (not included) into
the battery compartment (4). The bat-  SETTING THE ALARM TIME
tery maintains the clock in case of power   In order to set the current time, move the
failure. In such cases, the display will not   RUN/ALM/TIME (5) selector to the ALARM
work, but the time is being maintained.  position and turn the dial (8) to the left (to set
the minutes) or to the right (to set the hours).
RADIO                                When the time has been set, move the RUN/
1.  Set the ON/AUTO/OFF (6) selector to the   ALM/TIME (5) selector back to RUN. The two
ON position.                       blinking dots on the display (7) should stop
2.  Set the desired band using the band selec-  blinking.
tor (11).
3.  Tune to the desired radio station using the   ATTENTION!
tuning knob (10).                  Do not rotate the dial to fast because the clock
4.  Adjust the volume by turning the knob   cannot react at high speeds.
(12).
5.  Extend the antenna wire (2) fully for best   WAKING UP TO MUSIC
reception of FM-band signals.      1.  Set the ON/AUTO/OFF (6) selector to the
6.  Set the selector (6) to the OFF position to   AUTO position.
turn the radio off.                2.  Tune to the desired station by rotating the
frequency-tuning knob (10).
SETTING THE CURRENT TIME             3.   Set the desired volume by rotating the knob (12).
In order to set the current time, move the   4.  The radio will turn on at the pre-set time.
RUN/ALM/TIME (5) selector to the TIME po-  5.  Set the function selector (1) to the OFF po-
sition and turn the dial (8) to the left (to set   sition to turn off the alarm.
3
19.09.2011   9:19:05
3510_2_IM.indd   3                                                    19.09.2011   9:19:05
3510_2_IM.indd   3