Edge набор для ухода за волосами REMINGTON PG6030. Инструкция на русском языке

ALL IN ONE GROOMING KIT
PG6030

ENGLISH
Thank you for buying your new Remington® product.
Before use, please read these instructions carefully and keep them safe. Remove all
3                                        packaging before use.
A CAUTION
Use this appliance only for its intended use as described in this manual. Do not use
attachments not recommended by Remington®
Do not use this product if it is not working correctly, if it has been dropped or damaged, or
dropped in water.
2
9                              C KEY FEATURES
1                                                    1  On/off switch
2  Groomer
3  Wide trimmer
4  Detail trimmer
4                        5  Miniscreen shaver
6  Nose, ear, eyebrow trimmer
7  2 attachment guide combs
8  Charging Indicator
8                                                     9  Stand
10  Adaptor
• 3 year guarantee
5
C GETTING STARTED
,Charging your groomer
•  Before using your groomer for the first time, charge for 14-16 hours.
•  Make sure the product is turned off
•  Place your groomer into the stand, connect the adaptor to the product and then to the
mains. The charging indicator will light up.
Your appliance cannot be overcharged. However if the product is not going to be used for an
6                       extended period of time (2-3 months), unplug it from the mains and store. Fully recharge your
appliance when you would like to use it again.
To preserve battery life, let them run out every 6 months then recharge for 14-16 hours.
7                                             FHOW TO USE
,Attaching and removing guide combs
10                       •  With the trimmer blade facing away from you, slide the guide comb over the back of the
trimmer blade and click into position.
•  With the trimmer blade facing away from you, carefully push the guide comb away from
the wide head trimmer.
,Before you begin
Comb facial hair with a fine comb before you start trimming. Hairs should be dry and without
2                                                                                                                 3

ENGLISH                                                    ENGLISH
ETips for best results
any waxes or lotions before using the groomer              Comb your hair in the direction that it grows so that the hairs are at their maximum height and
,To thin and taper beards or moustache                     facing in the same direction.
•  Attach the wide trimmer blade.
•  Place the hair length attachment on the trimmer blade, select the desired length and   After trimming, lightly go over the trimmed areas with the foil to get a smooth clean finish.
switch on.                                               Since all hairs do not grow in the same direction, you may want to try different trimming
•  Start trimming under the chin, following the jawbone line. Work toward the ear and   positions (i.e. upwards, downwards or across) for better results.
upper beard line using an upward motion.
,Attaching and removing the trimmer attachments.
,To trim edge of beard or moustache                        Note: Always ensure the groomer is switched off before changing any attachments.
•  Attach the detail trimmer blade.                         •  To remove, hold the groomer with one hand and turn the trimmer head anti-clockwise
with the other.
•  Hold groomer with cutting blade facing you.              •  To attach, hold the groomer with on hand and turn the trimmer head clockwise with the
•  Start with edge of beard/moustache line, and with the cutting blades resting lightly   other.
against your skin, use slow movements to create a beard/moustache line.
,To trim sideburns                                         ,Using the detailed trimmer
•  Hold groomer with the surface (back side) of the blade guides against the skin.
•  Hold groomer with cutting blade facing you.              •  Use motions similar to using a wet blade to provide the closest trim.
•  Use a small comb to lift the hairs. Hold the comb at the desired beard or moustache      Note: This attachment provides a dual purpose solution for stubble or close results
length.
•  Move the groomer along the comb to cut the hairs. Use light pressure and well-controlled   without irritation.
movements to trim hair.
,Using your miniscreen shaver
•  Hold the groomer so the MiniScreen gently touches your face.
,Trimming the nape of your neck                             •  Use short, and well-controlled movements to shave around your beard/moustache. Use
•  Attach the wide trimmer blade.
•  Use your fingers to lift the hair at the base of your head up off the neck. Your index finger   your free hand to stretch your skin. This encourages the hair to stand upright, making it
easier to shave.
should be covering the roots of the hairs you are lifting to prevent accidental removal by   Note: The MiniScreen shaver was designed to shave the detail areas around your beard
groomer.                                                   moustache/sideburns. It was not designed to shave your entire face. For a close
•  Using your other hand, hold the groomer to the base of your neck with the cutting unit   comfortable shave, guaranteed, use one of Remington’s electric shavers.
facing up, and move the groomer up the length of the neck until the unit touches your
finger covering the hair roots at the base of your head.
Move the unit slowly when performing this operation and to keep the hair roots at the   C  CARE FOR YOUR GROOMER
base of your head out of the way of the groomer.         Care for your product to ensure a long lasting performance. We recommend that you clean your
groomer after each use.
,To remove hair from nose and ear                          The easiest and the most hygienic way to clean the groomer is by rinsing the product head after
•  Attach nose, ear & eyebrow attachment.                  use with warm water. Always keep the protective cap on the shaving head and keep the trimmer
•  Insert groomer’s cutting unit gently into the nostril or ear.  in the “off” position when the shaver is not in use.
•  Gently move the groomer in and out of the nostril or ear and at the same time rotate the
groomer.                                                 E After each use
•  Avoid inserting the cutting unit more than 6mm into your nostril or ear.
•  Rinse the accumulated hair from the cutters and shake off excess water. Alternatively, use
,To remove hair from eyebrows                                a brush.
•  Attach nose, ear, eyebrow attachment.                    •  Gently tap on a flat surface to remove hair particles, and brush the remaining hairs away.
•  Gently guide cutting unit to stray, unwanted hairs along the eyebrow line or protruding   •  Place one or two drops of cutter oil or sewing machine oil on the blades. Turn the clipper
from the eyebrow itself.                                   on to distribute the oil evenly, wipe off any excess oil.
•  To remove the hairs completely lower onto the skin and move over desired area.  •  Wipe the main unit with a damp cloth and dry immediately.
•  Use slow and well-controlled movements.                 Note: Ensure that the groomer is turned off when applying
the oil or rinsing under the tap.
4                                                                                                                 5