Contour триммер для бороды и усов REMINGTON MB4030. Инструкция на русском языке

BEARD TRIMMER
MB4030

ENGLISH                                                    ENGLISH
6                 Thank you for buying your new Remington® product.
Before use, please read these instructions carefully and keep them safe. Remove all
packaging before use.
5                                        ACAUTION
•  Use this appliance only for its intended use as described in this manual. Do not use
attachments not recommended by Remington®
•  Do not use this product if it is not working correctly, if it has been dropped or damaged,
or dropped in water.
C  KEY FEATURES
1  On/off switch
3                        7                    2  Zoom wheel
3  Length position indicator
4  Charge/recharge indicator
5  Trimmer assembly
6  Trimmer comb
7  Pop up trimmer
2                         8  Charging adaptor
9    Stubble comb
• 3 year guarantee
4                                                  C  GETTING STARTED
•  Before using your trimmer for the first time, charge for 14-16 hours.
1                              •  Make sure the product is turned off
•  Connect the adaptor to the product and then to the mains
•    The charging indicator will light up.
Your appliance cannot be overcharged. However if the product is not going to be used
for an extended period of time (2-3 months), unplug it from the mains and store. Fully
recharge your appliance when you would like to use it again.To preserve battery life, let
8                              9                            them run out every 6 months then recharge for 14-16 hours.
,Corded
Connect the appliance to the mains and recharge for 5 mins  before using.
A CAUTION
Extended mains use will result in the reduction of the battery life.
2                                                                                                                 3

ENGLISH                                                    ENGLISH
Note: Trimmer comb must be attached to the product in order to use the hair length
FHOW TO USE                                                 selector.
,Before you begin
•  Always comb your beard or moustache with a fine comb before you start trimming   ,To thin and taper beards/ moustaches
•  Attach an attachment comb to the 30mm Trimmer Blade.
,Adjusting the trim length                                  •  Use the zoom wheel to set the trimmer comb to the desired length setting. The setting
•  The trimmer comb can be adjusted to give you 9 different trim lengths simply by turning   will appear on the length position indicator. If you are trimming for the first time start
with the maximum trimming length setting
the wheel to the desired setting.                        •  Turn the unit on.
•  Turn the wheel clockwise for shorter length, anti-clockwise for longer length.  •  Place the flat top of the trimmer comb against the skin
•  The wheel will click into place as it reaches each setting, and the setting number will   •  Slowly slide the trimmer through the hair. Repeat from different directions as necessary.
appear on the length position indicator.                 •  If hair builds up in the trimmer comb during the trimming process, switch the unit off,
SETTING   HAIR DESCRIPTION       HAIR  LENGTH              pull off the comb and brush/rinse off
,To define the beard/moustache line
•  Hold trimmer with 30mm Trimmer Blade facing you.
•  Remove the trimmer comb attachment
•  Start with edge of beard/moustache line and gently lower the trimmer blade onto your
1        Stubble or Cropped look  1.5mm                  0.06’’  skin. Use motions towards edge of beard/moustache line to trim to desired locations in
facial area and away from beard in neck area.
2                        2.5mm    0.1’’                 •  For finer shaping, raise the pop-up trimmer. Shape as desired.
3        Short           4mm      0.16’’
C  BLADE RELEASE
4                        5.5mm    0.22’’                •  Remove the adjustable comb.
•  Push the release button on the back of the product.
5        Medium          7mm      0.28’’                •  Blade will release itself from its housing.
•  Remove the blade from the housing.
6                        9mm      0.35’’                •  To replace the blade, make sure the blade is aligned and the grooves on the blade
cartridge match up with slots in the housings.
7                        11mm     0.43’’                •  Push the blade into the housing until it snaps into place.
8                        14mm     0.55’’                C  REPLACING THE TRIMMER COMB
•  Hold the trimmer in one hand with your thumb firmly on the zoom wheel to keep it from
9        Long            18mm     0.71’’                  turning. Ensure that the length position indicator is at 1.
•  Slide the comb/shaver down the grooves until it clicks into place.
,0.5 – 5.5mm guide comb                                        Note: The trimmer comb attachment can only be placed on the trimmer one way; if it
The 0.5 – 5.5mm guide comb can be adjusted to give you settings of 0.2mm adjustment   does not fit properly remove and reverse it.
simply by turning the wheel to the desired setting. Turn the wheel clockwise for longer
length and anticlockwise for shorter length.                ETips for best results
The setting will appear on the length position indicator.   •  Beard, moustache and sideburn hairs should be dry.
•  Avoid using lotions before using your trimmer. Comb your hair in the direction that it
,Attaching and removing the 0.5 – 5.5mm guide        comb.    grows.
With the trimmer blade facing away from you, slide the guide comb on top of the trimmer   •  Remove trimmer comb attachment if you are: defining hairline edges such as sideburns,
blade and click into position.                                trimming the nape of your neck, trimming your beard line on front of neck.
With the trimmer blade facing away from you, carefully push the guide comb away from the
trimmer blade.
4                                                                                                                 5