Мотоцикл HONDA CBR929RR. Инструкция на английском языке

FORMATION
1 .  GENERAL                      I
SERVICE RULES                              1-1 LUBRICATION & SEAL POINTS                        1-19
MODEL IDENTIFICATION                       1-1       CABLE & HARNESS ROUTING                    1-23
SPECIFICATIONS                             1-3       EMISSION CONTROL SYSTEMS                   1-40
TORQUE VALUES                              1-12      EMISSION CONTROL INFORMATION
LABELS (U .S.A. ONLY)                      1-43
TOOLS                                      1-17
SERVICE RULES
1 . Use genuine HONDA or HONDA-recommended parts and lubricants or their equivalents . Parts that don't meet HONDA's
design specifications may cause damage to the motorcycle .
2 . Use the special tools designed for this product to avoid damage and incorrect assembly .
3. Use only metric tools when servicing the motorcycle . Metric bolts, nuts and screws are not interchangeable with English
fasteners .
4. Install new gaskets, O-rings, cotter pins, and lock plates when reassembling .
5. When tightening bolts or nuts, begin with the larger diameter or inner bolt first . Then tighten to the specified torque
diagonally in incremental steps unless a particular sequence is specified .
6. Clean parts in cleaning solvent upon disassembly . Lubricate any sliding surfaces before reassembly .
7 . After reassembly, check all parts for proper installation and operation .
8 . Route all electrical wires as show on pages 1-23 through 1-39, Cable and Harness Routing .
MODEL IDENTIFICATION
4
4
___1~0  I .                            +
OOD
00000
0                 • o
N                        G
0                  O             •             O
1          I.    O
7
/                 _   O  QO_
C:
1

GENERAL INFORMATION
ENGINE SERIAL NUMBER
FHAIVML 5EiiIAL Jill r„IHE-
(1) The frame serial number is stamped on the               (2) The engine serial number is stamped on the right
right side of the steering head.                           side of the upper crankcase .
I
VEHICLE IDENTIFICATION NUMBER (VIN)                    THROTTLE BODY IDENTIFICATION NUMBER
(3) The Vehicle Identification Number (VIN) is              (4) The throttle body identification number is
located on left side of the main frame on the               stamped on the intake side of the throttle body as
Safety Certification Labal .                                shown.
COLOR LABEL
i
(5) The color label is attached as shown . When
ordering color-coded parts, always specify the
designated color code.

GENERAL INFORMATION
SPECIFICATIONS
GENERAL
ITEM                                            SPECIFICATIONS
DIMENSIONS      Overall length                     2,065 mm (81 .3 in)
Overall width                      680 mm (26 .8 in)
Overall height                     1,125 mm (44 .3 in)
Wheelbase                          1,395 mm (54 .9 in)
Seat height                        820 mm (32 .3 in)
Footpeg height                     384 mm (15 .1 in)
Ground clearance                   130 mm (5.1 in)
Dry weight
49 states, Canada type           172 kg (379 Ibs)
California type                  174 kg (384 Ibs)
Curb weight
49 states, Canada type           197 kg (434 Ibs)
California type                  199 kg (439 Ibs)
Maximum weight capacity
49 states, Canada type           160 kg (353 Ibs)
California type                  164 kg (362 Ibs)
FRAME            Frame type                        Diamond
Front suspension                  Inverted telescopic fork
Front wheel travel                110 mm (4 .3 in)
Rear suspension                   Swingarm
Rear wheel travel                 135 mm (5 .3 in)
Rear damper                       Nitrogen gas filled damper
Front tire size                   120/70 ZR17 (58W) /Radial
Rear tire size                    190/50 ZR17 (73W) /Radial
Tire brand
Bridgestone                      Front: BT01OF /Rear: BT010R
Michelin                        Front : Pilot SPORT E /Rear : Pilot SPORT E
Front brake                       Hydraulic double disc brake with 4 pot caliper
Rear brake                        Hydraulic single disc brake with 1 pot caliper
Caster angle                      23°45'
Trail length                      97 mm (3.8 in)
Fuel tank capacity                18 .0 2 (4.76 US gal,3 .96 Imp gal)
ENGINE           Bore and stroke                   74.0 X 54.0 mm (2.91 X 2 .13 in)
Displacement                      929 cm3 (56.7 cu-in)
Compression ratio                 11 .3 : 1
Valve train                       Chain drive and DOHC
Intake valve  opens   at 1 mm     25° BTDC
closes-   (0 .04 in) lift  35° ABDC
Exhaust valve opens -             40° BBDC
closes                20° ATDC
Lubrication system                Forced pressure and wet sump
Oil pump type                     Trochoid
Cooling system                    Liquid cooled
Air filtration                    Paper filter
Crankshaft type                   Unit type
Engine dry weight                 62.1 kg (136 .9 1 bs)
Cylinder arrangement              Four cylinder, inline 30° inclined from vertical
Firing Order                       1-2-4-3