Стробоскоп INVOLIGHT BS1501 DMX. Инструкция на английском языке

I.  PRODUCT DESCRIPTIONS
Thank you for using our company the BS1501DMX, it is a powerful DMX
strobe that allows control flash speed and dimmer, and it has two operating
mode  by  changing  DIP  switch  setting:  DMX  self-test  mode  and  DMX  pack
mode . Prior to use, we suggest that you carefully read all of the instructions.
By following the instructions found in these operations, you can look forward
to reliable and satisfactory performance of your BS1501DMX for years to
come.
II.TECHNICAL SPECIFICATIONS                                                                                                                  1 23 4 5 6 7 8 910  Page 3
Power Input: AC 240V, 50Hz, 16A max.
6
Flash Tube : 1500W, 5x10 life
Circuit Breaker: 16A
DMX In/Out:3 pin female & male XLR socket x 1                                   IV.OPERATION INSTRUCTIONS
Dimensions : L453xW136xH207 mm                                                  1.  Please confirm power input is matched with that specified on this unit.
Weight: 5.6Kgs                                                                  2.  Plug in power cord to turn the power on.
3.  This unit has two operating modes:DMX self-test mode and DMX pack mode.
III.REAR FUNCTIONS                                                                  4.  Switch DIP switch 10 to OFF position,this unit is in DMX self-test
1.  Power Input: AC 240V, 60/50Hz, 16A max.                                             mode.There are two self-test modes:AUTO and MANUAL.Set DIP switch 9 to
2.  Circuit breaker: 16A.                                                               OFF,it performs AUTO self-test.When strobe flashes within the dimming
3.  Power Indicator: Indicator when power is on.                                        range from 0% to 100% and then from 100% to 0%,a slower or faster speed
4.  DMX DIP switch: Assign   DIP  switch  10  to  ON,the  unit  is  in  DMX  pack       will be executed.This strobe will flash with the regular speed corresponding to
mode.Follow DMX addressing printed on the rear for desired speed and                the variety of the duration of dimmer.Set DIP switch 9 to ON, it performs
dimming settings. Assign DIP switch 10 to OFF,   the unit is in DMX self-test       MANUAL self-test.DIPswitch 1,2,3 and 4 are assigned to control speed,and
mode , follow self-test settings to select desired chase.                           DIP switch 5,6,7 and 8 are assigned to adjust dimming level.
5.  DMX Indicator: Indicator when DMX is effective.                                 5.  Switch DIP switch 10 to ON position,this unit is in DMX pack mode.Follow
6.  DMX Signal Output: XLR female socket,use to connect other strobe.                   DMX address setting printed on the rear for desired flash speed and dimmer.
7.  DMX Signal Input: XLR male socket,use to receive DMX signal.                    6.  For safety,disconnect power cable when not using.
V.  WARNING
1.  Avoid direct eye exposure.
2.  Disconnect from main power before replacing lamps or servicing unit.

3.  Remember to always replacewith same lamp.                                                     =on    =off
4.  To prevent fire or shock hazard,do not expose this unit to rain or moisture.
5.  This product must not be used continously longer than 15 minutes under                    Level                 Level
maximum speed and dimmer.                                                                  ?)   1 Dip switch 4  Speed  ?)  1 Dip switch 4
3
2
2
3
(                     (
1              Slowest  1             Min.
2                     2
IV.APPENDIX                                                                                    3                     3
1.  In DMX pack mode,please refer to following illustrations for desired channel               4                     4
setting:                                                                                   5                     5
DMX Address Table
DMX Address Setting       (Dip switch 10=ON)                                     6                     6
Switch#  1  2  3  4  5  6  7  8  9 10  START  SWITCHS ON  START  SWITCHS ON          7                     7
CH#         CH#
on  off                     1     1     11    1,2,4                                   8                     8
2     2     12    3,4
9                     9
3    1,2    13    1,3,4
Switch  (1)
(2)                 4     3     14    2,3,4                                   10                    10
(4)                5    1,3    15   1,2,3,4
(8)                                                                        11                    11
Binary     (16)            6    2,3    16     5
(32)
(64)        7    1,2,3   . ..  . ..                                   12                    12
(128)      8     4      . ..  . ..
(256)                                                              13                    13
Value                      9    1,4     . ..  . ..
Address 105
10   2,4    511  1,2,3,4,5,6,7,8,9                        14                    14
2.  In DMX self-test mode,please follow below table for desired chase:                         15                    15
DMX Self-test                                                           16             Fastest  16            Max.
(Dip switch 10=OFF)
MANUAL              AUTO
Dip switch  Function  Dip switch  Function
9      ON       9      OFF
1~4    SPEED
1~8
5~8
3.  In MANUAL of self-test mode, spee and dimmer are classified as 16 levels
respectively,and are specified as follows: