Звуковая карта M-AUDIO Delta 1010AI. Инструкция на английском языке

Delta 1010-AI MANUAL
™
Version 10AI 053100
Table of Contents
Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
What’s in the Box?   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front and Back Panel Descriptions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setting up the Delta 1010-AI with your Delta 1010   . . . . . . . . . . . . . . . . . . . . . . 4
Hooking Up Your ADAT Optical Device   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using Your Delta 1010-AI  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADAT to Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ADAT to Analog Outs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Analog Ins to ADAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ADAT Thru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mixed Modes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Standalone Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Master Clock Settings and the Delta 1010-AI  . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Synchronizing your ADATs   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Limited Lifetime Warranty   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Introduction
Congratulations on your purchase of the Delta 1010 ADAT Interface, designed
and manufactured by M Audio.  The Delta 1010-AI is a companion to the Delta
1010 PCI Recording System, and when used together, the Delta 1010-AI will
add ADAT Optical 8-channel input and output capability to your Delta 1010.
Please follow the instructions contained in this manual to properly connect the
Delta 1010-AI to your existing Delta 1010 setup, and to completely understand
the versatility of the Delta 1010-AI.  If you have not yet installed your Delta
1010, please refer to the Delta 1010 manual to install and configure the Delta
1010’s PCI card.
Features
• ADAT* I/O for PC(Windows 95/98, NT, Linux) and Apple (MacOS)
computers operating up to a full 24 bit 48kHz.
•Provides ADAT record through and playback using premium 24 bit
converters.
• Simultaneous ADAT recording and computer playback.
• Select between analog and ADAT optical for computer input.
• Select between computer out and ADAT in for routing to the Delta 1010
D/A section.
• Select between computer out and analog in for ADAT input source.
• ADAT In to ADAT Out “Thru” mode.
* ADAT is a registered trademark of Alesis.
What’s in the Box?
Contained in the Delta 1010-AI package, you should find the following:
• This manual.
• Delta 1010 ADAT Interface Module for the Delta 1010.
• 25-pin male to female standard printer cable.
• 9v DC 500 mA center positive power supply.
2

Front and Back Panel Descriptions
?  ?               ?  ?      ?   ?        ?
?
?  ?
Front Panel
1. ADAT to Host “Enabled” LED: When lit, this LED indicates that “ADAT to
Host” mode has been enabled.
2. ADAT to Host Button: Pressing this button and locking it to the “in”
position will enable “ADAT to Host” mode.  The incoming Delta 1010-AI
ADAT signal will then be routed to the Delta 1010 PCI “host” card in your
computer.
3. ADAT to Analog Outs “Enabled” LED: When lit, this LED indicates that
“ADAT to Analog Outs” mode has been enabled.
4. ADAT to Analog Outs Button: Pressing this button and locking it to the “in”
position will enable “ADAT to Analog Outs” mode.  The incoming
Delta 1010-AI ADAT signal will then be routed directly to the analog outs
on the Delta 1010 rack unit.
5. Analog Ins to ADAT “Enabled” LED: When lit, this LED indicates that
“Analog Ins to ADAT” mode has been enabled.
6. Analog Ins to ADAT Button: Pressing this button and locking it to the “in”
position will enable “Analog Ins to ADAT” mode.  Analog inputs on the
Delta 1010 rack unit will then be routed directly to the ADAT out on the
Delta 1010-AI.
7. ADAT Thru “Enabled” LED: When lit, this LED indicates that “ADAT
Thru” mode has been enabled.
8. ADAT Thru Button: Pressing this button and locking it to the “in” position
will enable “ADAT Thru” mode.  The Delta 1010-AI ADAT In is then
routed directly to the Delta 1010-AI ADAT Out.
9. Power Indicator LED: When lit, this LED indicates that power has been
applied to the Delta 1010-AI.
10. Power Button: Pressing the “Power” button and locking it to the “in”
position will apply power to the Delta 1010-AI, provided that the proper
power supply has been plugged into the Delta 1010-AI 9v DC jack.
3