На сайте 124213 инструкций общим размером 502.86 Гб, которые состоят из 6279321 страницы

Электрогитары (Excl. Prestige) IBANEZ Electric Guitars (Excl. Prestige). Инструкция на английском языке

Руководство пользователя IBANEZ Electric Guitars (Excl. Prestige). Основные функции, характеристики и условия эксплуатации изложены на 2 страницах документа в pdf формате.

Информация

Раздел
Музыкальное оборудование
Категория
Музыкальные инструменты
Тип устройства
Электрогитары (Excl. Prestige)
Производитель (бренд)
IBANEZ
Модель
IBANEZ Electric Guitars (Excl. Prestige)
Еще инструкции
Музыкальные инструменты IBANEZ, Электрогитары (Excl. Prestige) IBANEZ
Язык инструкции
английский
Дата создания
03 Марта 2019 г.
Просмотры
88 просмотров
Количество страниц
2
Формат файла
pdf
Размер файла
2.34 Мб
Название файла
ibane_manual_electric_guitars_excl_prestige.pdf

Фото

Страница 1Страница 2

Просмотр

Доступно к просмотру 2 страницы. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.

  • NECK                                                          PICKUPS                                                  QUIK CHANGE TAILPIECES
    Maintenance ??
    Our congratulations and deepest thanks on                Ibanez steel string models are equipped with adjustable truss rods. The  The output level of the                       The height adjustment of the QUIK               (C)
    purpose of a truss rod is to adjust the neck to counteract string tension.  instrument as well as the                  CHANGE III can be adjusted by
    making Ibanez your choice of instrument. Ibanez          There are many reasons for truss rod adjustments. One of the most  quality of the signal can be                        using a slot head (-) screwdriver or
    standards are second to none. All Ibanez                 frequent reasons is changing string gauges or tuning pitch which can  affected by the pickup height.                   a coin turn the adjustment studs at
    affect string tension. String tension changes may affect the string height  Pickup height should be                    either side of the tailpiece (C).
    instruments are set up to our strict quality control     and cause fret buzz or notes that don’t ring true. To adjust the truss rod,  adjusted until the volume of
    locate the truss rod nut and adjust it by inserting the correct wrench into  neck and bridge pickups are
    standards before shipping. The purpose of this           the nut and tightening (clockwise) or loosening (counter clockwise) the  almost equal with both
    manual is to explain how to maintain your                rod. Truss rod tension can be measured by installing a capo at the first  volumes wide open.  The volume may drop drastically if the pickup
    fret the holding the strings down at the fret position where the neck joins  height is too low.  As the pickups are magnetic, fret buzzing and
    instrument’s finish and to keep your guitar playing      the body. Insert a thickness gauge between the string and the fret at the  distortion may occur if the pickup is too close to the strings. Use a small  QUIK CHANGE III
    screwdriver to make adjustments to raise or lower the pickup.
    as well as it did when it left our factory.              8th fret. There should                 LOOSEN
    between 0.3 mm to 0.5mm  LOOSEN              TIGHTEN          *Instruments that have adjustable pole pieces can be adjusted to balance the output of each string.
    TIGHTEN
    clearance. That clearance is
    referred to as “neck relief.”
    CLEANING                                                 Too much neck relief can                                      Guitar Bridges ??
    cause the neck to have
    Regular cleaning of your                                 higher action in the middle of                                GIBRALTAR CUSTOM BRIDGE
    guitar is one the most                                   the neck causing poor
    important ways you can                                   intonation and uncomfortable                                  The height adjustment can be
    maintain the finish and                                  playability. No neck relief can                               adjusted by 4 pcs of 2.0mm of allen       B
    lengthen string life. After                              cause fret buzz.                  LOOSEN                      screws (B) on the bridge. Since the    C
    playing, wipe down your                                  *Appropriate care must be taken when                          adjustment screws are locked by the                            QUIK CHANGE MINI         QUIK CHANGE CLASSIC
    instrument to remove any                                 adjusting the neck and we recommend only  TIGHTEN             bridge lock screw (A), you must  A
    perspiration from the                                    qualified technicians perform this procedure.                 loosen the bridge lock screw by
    instrument. Perspiration can actually contain acids that can be corrosive                                              3.0mm Allen wrench before                                                                                (E)
    to the strings and metal parts of the guitar. Gloss finish guitars should be                                           adjustment.
    polished with polish formulated specifically for musical instruments, and                                              Each saddle is also locked by a
    0.3~0.5mm
    a soft, treated guitar cloth or a cotton rag. Abrasive rags such as                                                    saddle lock screw (C). To adjust the            D        QUIK CHANGE ULTRA / FINE
    polyester can scratch the finish. Oil finished guitars should be wiped                                                 intonation, use a 2.0mm Allen                            TUNNING FUNCTION
    clean immediately after playing with a dry cotton rag only. If your guitar                                             wrench to loosen the saddle locke                        QUIK CHANGE ULTRA has FINE
    has become discolored due to extended use or heavy perspiration,                         8TH FRET                      screws, and then adjust the                              TUNER function.
    factory appearance, see a qualified guitar repair person about methods                                                 Intonation screw (D) by a 2.0mm                          Even after by the tuning machine,
    to restore the oil finish to its original factory appearance.                                                          Allen wrench. When you are finished with the adjustment, lock the  you can make a quick-fine
    saddle and tune the guitar.                              adjustment by FINE TUNERS (E).  QUIK CHANGE ULTRA
    DOWNSHIFTER
    STRINGS AND TUNING MACHINES                              ACTION                                                        GIBRALTAR III & FULL TUNE III
    INSTALLING THE STRING
    If strings become dirty, discolored, or produce a        Ibanez guitar and bass string action is set at the                                                                     To install a new string insert the ball end of  3
    dull sound or buzz, replace the strings with new         factory. However there are many reasons that an                    (A)                                                 the new string into the slot and place the ball  2
    ones. For best results we recommend replacing            instrument’s string height can change. Instruments                                                                     end into the internal hook area of the saddle  1
    one string at a time, this will help to avoid            can be affected by changes in temperature and                                                                (A)       as shown. Pull the string tight to the saddle
    removing the string tension from the neck. When          moisture. High string action can make the guitar                                                                       and restring the rest of the string as you
    normally would on the machine head.
    replacing strings with different gauge strings, it       difficult to play. If the string action is too low, fret
    may be necessary to adjust the truss rod tension.        buzz or unclear notes can occur.  To remedy this,                                                                      SPECIAL TUNING
    (We recommend only qualified technicians                 follow the instructions for the particular type of                               (B)               (B)                 The Downshifter also allows the pitch to be raised by setting the standard
    perform this.) Instruments that have tremolo             bridge installed. In the case of string action, make                                                                   tuning while the lever is in the lower position. When the lever is raised the
    sure the guitar is in tune and the truss rod is adjusted properly. Ibanez
    systems installed may need to be adjusted after          action is set at the 14th fret. The action may also need to be readjusted                                              pitch will also be raised and can be adjusted to the desired pitch.
    string replacement as changes in string tension  3       after the neck has been adjusted or strings have been changed to a                                                     The Ibanez DOWNSHIFTER allows the pitch of a string to be dropped to a
    can cause the tremolo to raise or lower. Ibanez          different gauge. Follow the instructions in the relevant bridge manual to  The action can be adjusted by using a slot head (-) screwdriver to turn  preset desired position with a simple lever operation. To achieve precise
    guitars and basses are factory equipped with the  2      make adjustments.                                             the adjustment bolt at either end (A).                   tuning for both the up and down positions, you will need to preset both
    following string gauges. Please follow the                                                                             The intonation can be adjusted by moving the saddle forward or  lever settings before operating the Downshifter.
    instructions below for your particular model.            *If strings other than those described above are used, gradually increase the action clearance from the treble side  backward using a screwdriver to turn the adjustment screw of each  TUNING
    through to the bass side.
    The strings should be tightly wound on to the                                               TREBLE SIDE  BASS SIDE     saddle (B).                                              First check that the Downshifter lever arm is
    tuning machines from top to bottom with 2 to 3  1                   .009-string's guitars except Gio Ibanez  1.5mm  2.0mm                                                       raised to the up position then tune the string
    all Gio Ibanez & .010-, .014- string's guitars
    1.7mm
    2.3mm
    string wraps around the post. In the case of                                                                                                                                    normally using the standard tuning machines
    unwound guitar strings, the ends of the strings          INTONATION                                                                                                             on the headstock.
    should be prepared as shown in the diagram to                                                                          HARDTAIL BRIDGE                                          (Note: the Downshifter tuning screw has no
    TIGHTEN
    prevent unintentional slippage from the posts. In        Intonation adjustment is                                                                                               effect on the pitch in the up position.) Next,
    the case of tuning machines, where the string            the operation of                                              To change strings, thread the new                        lower the lever on the Downshifter to the down position and the pitch of
    ends are inserted into the posts, the string can be      adjusting the location of                                     strings through the string grommets                      the string will drop down. Adjust the rear
    cut to length in advance using a pair of string          the string at the saddle                                      located on the back of the guitar and                    tuning screw clockwise to reduce the pitch,
    cutters.                                 LOOSEN          to compensate for                                             bring them up and over the saddle.                       or counter clockwise to raise the pitch. This
    If the tuning machines are sealed gear units, they       different string gauges                                       The intonation can be adjusted by                        adjustment can be done by hand or with a
    or different tunings.
    are self-lubricating types. The set screws for the tuning knob are  Follow the instructions                            adjusting the saddle forward or                          standard screwdriver or a coin until the
    adjustment screws that can be tightened with a small Phillips head  of the particular bridge intonation below. Intonation is properly set when  backward using a Phillips (+) head  desired down pitch is acquired. (The preset
    screwdriver to increase the tension.                                                                                   screwdriver on the intonation                            factory pitch is set one whole step down to
    the 12th fret note and the 12th fret harmonic are exactly the same note .  adjustment screw at the rear of the         D.) When the lever is raised to the up
    *The use of coarse strings may lead to buzzing and sound distortion. Using strings that have twists or kinks may  This is the center point of the scale and the most accurate way of setting  bridge. String height is controlled by  position, the thumbscrew can be turned
    cause buzzing or decreased sustain. Make sure that the new strings are smooth and free from any defects
    before installing.                                       a standard scale length. With the harmonic note as the standard, if the  raising or lowering the small Allen screws using a wrench on either side  freely but will have no effect on the raised lever pitch. However, it will
    fretted note is flat move the bridge saddle forward toward the headstock                                               affect the settings of down lever pitch.
    STRING GAUGES                                                                                                         of the saddle.
    (a) to decrease the string length. If the fretted note is sharp, move it back
    Solid guitars w/Tremolo, JTK, ICX, RVX & ALL Gio  .009/.011/.016/.024/.032/.042 inch                                                                                           PLEASE NOTE: The Downshifter device was designed to provide the
    RG321MH, SZ, AXS, AR,ARC, ARX & IC  .010/.013/.017/.026/.036/.046 inch  away from the headstock (b) to increase the string length intonation                                   highest level of pitch accuracy. However, it should be understood that
    7-String model              .010/.013/.017/.026/.036/.046/.054 inch  adjustments.                                                                                              the Downshifter is a mechanical device. Pitch variations and tuning
    MMM1                        .014/.017/.030/.040/.056/.074 inch
    *Please note that strings can be broken when the saddle is moved, so always loosen the strings before                  readjustments, especially after frequent use, are to be expected.
    making adjustments.
    RG(*), SA120 : 2 PICKUPS (H-H)
    (*)except RG120                                               Guitar Controls ??
    Guitar Electronics ??
    CONTROLS
    SWITCHING FUNCTION
    1 VOL(*), 1 TONE & 5 WAY LEVER SELECTER
    Ibanez Instruments are unique in the simplicity and versatility of our                                                 *SAS/SA260 : TRUE-DUO Switch on Volume  1 VOL, 1 TONE & 3 WAY LEVER SELECTER  1 VOL, 1 TONE & 3 WAY TOGGLE SWITCH  2 VOL, 1 TONE & 3 WAY TOGGLE SWITCH
    switching systems. Each model was designed to allow the maximum
    amount of useful pickup positions with the simplest operations.                                                        JEM, PGM, NDM, RG, SAS, SA, GSA60,  MMM, RG120, S520EX, GSA20,  ICX, RVX            SZ, ARC, ARX
    GRX20,22, GAX30
    GRX70,40
    NECK        CENTER        BRIDGE
    SPLITS FUNCTION                                                Humbucking is parallel connected.                                                                                                               NECK VOLUME
    WITH "TRUE-DUO"SYSTEM                                                                                                          *                                                                            BRIDGE
    VOLUME                    VOLUME                               VOLUME
    *BRIDGE PICKUP : "TRUE-DUO BUCKER"                                                                                                                         3 WAY                                            VOLUME     3WAY PICKUP
    OTHERS                                                             PICKUP SELECTOR           PICKUP SELECTOR                     TONE                         SELECTOR
    5 WAY
    SAS32 : 2 PICKUPS(H-H)                                                                                                       TONE                      TONE                          TOGGLE SWITCH            TONE
    VOLUME POT
    HUMBUCKER PICKUP MODE      SWITCH PUSH DOWN              JS, JTK : 2 PICKUPS (H-H)
    1 VOL, 1 TONE & 3 WAY TOGGLE SWITCH
    1 VOL, 1 TONE(*) & 3 WAY TOGGLE SWITCH  & 2 SEESAW SWICHES  2 VOL, 1 TONE & 3 WAY TOGGLE SWITCH  2 VOL, 2 TONE & 3 WAY TOGGLE SWITCH
    NECK        CENTER        BRIDGE
    VOLUME POT                     NECK         CENTER       BRIDGE                             JS                         JTK                           GSZ                        AXS, AX, GAX70,75
    SINGLE PICKUP MODE
    SWITCH PULL UP                                                                              (*)Coil Tap Switch on Tone
    JS, JTK (WHEN COIL TAP SWITCH WORKED)
    SEESAW SW. FOR BRIDGE PU
    SEESAW SW. FOR NECK PU                 NECK                   3 WAY
    VOLUME                                              TOGGLE      VOLUME           PICKUP SELECTOR
    VOLUME                       BRIDGE VOLUME
    3 WAY
    PICKUP SELECTOR                                                                 NECK TONE    NECK
    VOLUME
    TONE                         TONE
    BRIDGE TONE
    TONE
    w/COIL TAP ON/OFF SW.  TOGGLE SWITCH
    NECK        CENTER        BRIDGE                                                                                                                                                                                 BRIDGE VOLUME
    HUMBUCKERS                                         NECK         CENTER       BRIDGE
    PARALEL COONNECTED
    JS : Coilt Tap Switch by TONE POT
    Pull up=TAP ON NECK&BRIDGE Both
    SAS36/SA260 : 3 PICKUPS(S-S-H)                                        pickups
    VOLUME POT
    HUMBUCKER PICKUP MODE      SWITCH PUSH DOWN
    JTK : Coil Tap Swith by SEESAW Switch
    SEESAW DOWNED UPFOWARD=TAP ON
    SZ : 2 PICKUPS (H-H)
    2 VOL, 2 TONE & 3 WAY TOGGLE SWITCH
    NECK        CENTER        BRIDGE
    VOLUME POT                                                                                  AR, IC
    SINGLE PICKUP MODE
    SWITCH PULL UP
    3WAY
    PICKUP SELECTOR
    NECK TONE
    NECK
    NECK        CENTER       BRIDGE                                          VOLUME
    BRIDGE      BRIDGE
    TONE       VOLUME
    NECK        CENTER        BRIDGE                       AR, ARC, ARX, AXS, GAX(*), IC, ICX, RVX, GSZ:
    2 PICKUPS (H-H)
    (*) except GAX30
    SPLITS FUNCTION
    JEM. PGM, RG, GRG, S(*), EXR, NDM, GRX :
    3 PICKUPS (H-S-H)
    (*) except S520EX
    NECK        CENTER       BRIDGE
    MMM, RG120, S520EX, GSA, GRX, GAX30 :
    2 PICKUPS (H-H)
    NECK        CENTER        BRIDGE
    GSA, GRX : 3 PICKUPS (S-S-H)
    NECK        CENTER       BRIDGE
    Printed in China     AUG2005WEG    ©2005
    This is to certify that the aforementioned
    NECK        CENTER        BRIDGE
    equipments fully conform to protection
    requirements of the following EC council directives.
    DIRECTIVES:89/336/EEC Electromagnetic compatibility
  • REPLACING THE STRINGS                                         ZR (ZERO RESISTANCE) TREMOLO                             ADJUSTING THE ZERO POINT SYSTEM
    Tremolos ??
    The EDGE-PRO II tremolo will accommodate                                                                               The Zero Point system makes it easier to
    either strings from which the ball end has                                                                             tune a floating tremolo unit, provides
    EDGE PRO II TREMOLO                                      been cut, or conventional strings from                        TREMOLO ARM                                              greater tuning stability after arming, and
    which the ball end has not been cut.                          Loosen the screw cap, insert the arm into the tremolo unit, and rotate it  limits the tuning drift that would
    TREMOLO ARM INSTALLATION                                 To remove a string, use a 3 mm Allen                          to fasten it in place (Fig.8). Rotate the arm to adjust it to the desired  otherwise occur when a string breaks.
    The tremolo arm can be inserted and                      wrench to loosen the pressure pad screw of                    height. The arm torque is adjusted by the tightness of the screw cap. To  *If the Zero Point system is not
    remove the arm, loosen the screw cap and rotate the arm counter-
    removed very easily. Insert the arm into                 the locking nut (Fig.1), remove the string     FIG.1          clockwise (Fig.9).                                       adjusted to the correct position it will
    the armhole on the tremolo base plate. Pull              from the tuning machine, and use a 3 mm                                                                                not function optimally, since it will
    up on the arm to remove it.                              Allen wrench to loosen the string stopper                                                                              either be completely floating, or the          FIG.14
    screw of the saddle (Fig.2). Turning this                                                                              Zero Point system and the string
    counter-clockwise will automatically retract
    the holder block, so loosen the string stopper                                                                         tension will be in balance. You must
    screw all the way until the holder block                                                                               perform this adjustment accurately.
    stops retracting. Remove the old string,
    ARM ROTATION TORQUE                                      insert approximately 3 cm of the new string  FIG.2                                                                     
    The rotation torque of the arm can be                    with ball end into the saddle, and while
    Main Spring
    adjusted by raising the tremolo and                      making sure that the string is positioned in                                                                                              Stopper
    inserting a 2.0mm Allen wrench in                        the center of the saddle, tighten the string                                   FIG.8                          FIG.9         Tremolo Block
    the screw (A) on the tremolo block,                      stopper screw (Fig.2). Turning this clockwise                                                                                                          2
    Turning this screw clockwise will                        will automatically advance the holder block,
    tighten the arm torque and turning                       so after making sure that the string is firmly                FINE TUNING                          A
    the screw counter clockwise will                         fastened, wind the string around the tuning                   Even after locking the locking  B  C
    loosen the arm torque.            A                      machine post, tune it, and then tighten the    FIG.3          nut, you can use the fine tuners                                           1         Stop Rod
    pressure pad of the locking nut.                              (Fig.10 A) to make fine
    When installing a wound string from which the ball end has been cut off,                                                                          With the guitar tuned correctly, adjust the
    Main Spring make sure that the Stop Rod
    you can leave the overwound portion of the winding intact in order to  adjustments to the tuning of                                               makes contact with the Tremolo Block
    each string.
    prevent the winding from loosening. Insert approximately 1~3 cm of the  You should adjust all of the fine                                         and Stopper.
    ARM ACTION                        B                      tip into the saddle, and install the string in the same way as a  tuners to the center of their
    The tremolo arm action can be                            conventional string from which the ball end has not been cut off.  adjustable range before you lock
    Since the attachment angle of the tremolo will change significantly if all
    adjusted by using a 2.0mm Allen                          strings are removed at once, you should replace the strings one at a time.  the locking nut.  FIG.10
    wrench on the screw (B) of the                           On the bottom of each saddle there is a guide stopper that indicates the
    tremolo block.
    length of string to be inserted. The appropriate length will be inserted if                                                                       If the Stop Rod does not make contact
    you insert the string until the tip contacts this guide.      ADJUSTING THE ACTION                                                                with the Tremolo Block and Stopper,
    If a string breaks at the saddle, it may fall into the tremolo cavity when  To adjust the entire tremolo unit up or down, use an Allen wrench to turn  adjust the Main Spring adjustment screw
    until contact is made.
    you loosen the string stopper screw. Remove the broken string either by  the stud bolt (Fig.10 B) located at the left and right of the tremolo unit.
    detaching the tremolo spring cavity cover plate from the back of the  (This cannot be adjusted for each individual string.)
    guitar, or from the opening in the cover plate. If the broken spring
    remains in the saddle, remove it from above.
    Note: Before you tune a string, make sure that the string stopper screw is firmly tightened.
    Note: To prevent the string stopper screw from falling out, do not loosen it more than three
    FINE TUNING                                              turns after the holder block has stopped retracting.          ADJUSTING THE INTONATION
    Even after locking the locking nut,                                                                                    Loosen the string stopper bolt of the                                               With the guitar tuned correctly, Stop Rod
    must make contact with the Tremolo
    you can use the fine tuners to make           C                                                                        locking nut (Fig.11). Remove the                                                    Block and Stopper. If it is adjusted
    fine adjustments to the tuning of                        TREMOLO SPRINGS                                               intonation adjustment bolt (Fig.12 B)                                               correctly, the tension while pushing down
    on the arm will be slightly less than
    each string.                                             The EDGE-PRO II tremolo is designed to                        from within the bridge unit, fasten it                                              tension while pulling up.The balance of
    You should adjust all of the fine                        function optimally when it is installed                       into the screw hole in the rear of the                                              force is about 3:7 (With this setup, stop
    tuners (C) to the center of their                        approximately parallel with the surface                       saddle, and tighten it so that the tip of                                           rod must the tremlo block and stopper
    even the 1st string is comlpetely loosened.)
    adjustable range before you lock the                     of the guitar body (Fig.4). The angle at       FIG.4          the bolt contacts the boss of the              FIG.11
    locking nut.                                             which the tremolo is attached can be                          bridge unit. Loosen the saddle lock bolt
    adjusted by changing the length of the                        (Fig.10 C), and turn the intonation
    tremolo springs inside the tremolo spring                     adjustment bolt to adjust the position                                              Again, if the Stop Rod does not make
    cavity in the back of the guitar body.                                                                                                            contact with theTremolo Block and
    ADJUSTING THE ACTION              F                      Working through the adjustment holes in                       of the saddle. After completing the                                                 Stopper, adjust the Main Spring
    To adjust the entire tremolo unit up     E     G         the tremolo spring cavity cover plate, use                    adjustment, tighten the saddle lock                                                 adjustment screwuntil contact is made.
    or down, use an Allen wrench to turn                     a Philips (+) screwdriver to turn the  FIG.5                  bolt sufficiently to prevent the saddle                   
    the stud bolt (E) located at the left                    tremolo tension adjustment screws to                          from moving forward during tuning,                        When a string breaks,because of the tension of neck,the tuning of other strings will be a
    little higher butstill limits within acceptable range.
    and right of the tremolo unit. (This                     adjust the length of the tremolo springs.                     and store the intonation adjustment
    cannot be adjusted for each                              If the tremolo is tilted forward toward the                   bolt inside the bridge unit.
    individual string.)                                      neck of the guitar (Fig.5), turn the screws                                                                            SWITCHING TO FLOATING OPERATION
    clockwise to tighten the springs.                                                                                      By stopping the Zero Point system from
    Conversely, if the tremolo is tilted                          REPLACING THE STRINGS                                    functioning, you can make the tremolo
    backward away from the neck (Fig.6),  FIG.6                   Loosen the string stopper bolt of the                    float completely. While holding the arm
    turn the screws counter-clockwise to                          locking nut (Fig.11), completely loosen        FIG.12    up, remove the stop rod and sub spring.
    loosen the springs. Tune the guitar                           the string at the tuning machine, use                    With the guitar tuned correctly, use the
    accurately, re-check the angle of the                         an Allen wrench to loosen the string                     main spring adjustment knob (Fig. 14E)
    ADJUSTING THE INTONATION                                 tremolo, and repeat the adjustment until                      stopper bolt of the bridge saddle                        to adjust the angle of the tremolo unit. If
    Before you adjust the intonation, use a 3 mm Allen wrench to loosen the  the tremolo angle is correct. The EDGE-       (Fig.12 A), and remove the old string.                   the tremolo unit is tilted forward toward
    PRO II tremolo is designed to function
    pressure pad screws (G) of the locking nut so that the strings are  optimally when three springs are                   Use wire cutters to remove the ball                      the neck, turn the spring adjustment
    released. Use a 2 mm Allen wrench to loosen the saddle lock screws (F)  tensioned equally with a 0.009" gauge  FIG.7   end from the new string as shown in                      knob in the plus (+) direction.
    of each saddle, and move the saddle. Firmly tighten the saddle lock  set of strings installed. If you replace the strings with a different gauge set,  Figure 13, insert this end of the string  Conversely, if the tremolo unit is tilted
    screws, tune the guitar, and then check the intonation. Repeat these  you can adjust the tremolo angle by changing the number of springs or the  into the bridge saddle, fasten it firmly,  backward away from the neck, turn the
    adjustments until the intonation is correct, and then tighten the pressure  way in which the springs are installed.    and then tighten the string at the                       spring adjustment knob in the minus (-)
    pad screws of the locking nut.                           Loosen all strings before you add or remove a tremolo spring.  tuning machine. After tuning, check                     direction.
    You may install each saddle lock screw in either the forward or rear  The EDGE-PRO II tremolo uses a block lock mechanism to fasten the  the angle of the tremolo unit, and     *You will need to tune repeatedly during
    position, depending on the position of the saddle.       tremolo springs to the block. Before you change the number of springs or  fasten the string stopper bolt of the  FIG.13  the process of adjusting the tremolo
    The unit is designed so that the fine tuning screw will not operate if the  the way in which they are installed, use a Philips (+) screwdriver to  locking nut to finish the procedure.  angle in the floating state, since the
    position of the saddle extends beyond the front edge of the base plate.  remove the block lock (Fig.7).                                                                         tuning will drift each time you adjust the
    main spring adjustment knob.
    Note: When loosening the saddle lock screws, you must loosen the strings sufficiently before  NOTE: If you want to install four or five tremolo springs, insert the springs into the block nut
    making adjustments.                                      attachment screw holes. (In this case, it will not be possible to attach the block nut.)
    EDGE III TREMOLO                                         ILT LOCKING TREMOLO                                           FAT/SAT TREMOLO                                         INTONATION ADJUSTMENT
    (SAT PRO)
    TREMOLO ARM INSTALLATION                                 TREMOLO ARM              (B) (D)   (A)                        TREMOLO ARM INSTALLATION                                To adjust the intonation, use a 1.5 mm  (C)
    The tremolo arm can be inserted and removed              Insert the tremolo arm into the                               The tremolo arm can be inserted and                     Allen wrench to turn the screw located  (D)
    very easily. Insert the arm into the armhole on          arm socket and tighten the                                    removed very easily. Insert the arm                     at the rear of the saddle (E). Turn the
    the tremolo base plate. Pull up on the arm to            fingertip tension adjustment                     (E)          into the armhole on the tremolo base                    screw clockwise to move the saddle
    remove it.                                               wheel. The rotation torque of the                             plate. Pull up on the arm to remove it.                 toward the rear, or counter-clockwise
    arm can be tightened or loosened                                                                                      to move the saddle forward.                   (E)
    by adjusting the tremolo arm nut                                                                                      INTONATION ADJUSTMENT
    located at the base of the tremolo                                                                                    (FAT20)
    ARM ROTATION TORQUE                                      arm.                                                                                                                  To assure that no movement can  SAT PRO
    occur each saddle has a set screw
    The rotation torque of the arm can be adjusted                                                                         TREMOLO ARM ADJUSTMENT                                  that locks the saddle. When adjusting the
    (SAT PRO)
    by raising the tremolo and inserting a 1.5mm                                                                           To adjust the height of the arm,                        intonation, loosen the saddle lock screw  (D)
    Allen wrench in the screw (A) on the tremolo             FINE TUNING                                                   remove the tremolo spring cover                         using a 2mm Allen wrench. (D)
    block, turning this screw clockwise will                 After locking the top lock, fine tuning the instrument can be done by                                                                                                  (E)
    (A)                                                                       from the back of the guitar, and use                    To adjust the intonation, insert a 2.5mm
    tighten the arm torque and turning the screw             turning the fine tuning screws (A).                           a 3 mm Allen wrench to turn the                         Allen wrench into the saddle screw at the
    counter clockwise will loosen the arm torque.            *To allow maximum fine tuning adjustment, it is recommended that the fine tuners be set to the middle position        rear of the tremolo. Turning the wrench
    before locking the nut.                                       height adjustment screw attached to
    ARM ACTION                                   (B)                                                                       the bottom of the tremolo block.                        clockwise will adjust the saddle
    The tremolo arm action can be adjusted by                                                                              Tightening this in the clockwise                        backward. Counter clockwise will adjust
    using a 3.0mm Allen wrench on the screw (B)              ADJUSTING THE STRING HEIGHT                                   direction will raise the height.                        the saddle forward. After the correct
    of the tremolo screw.                                    The height adjustment of the tremolo can be                   ARM ROTATION TORQUE                                     intonation location of the saddle is set  FAT20
    tighten the saddle lock down screw to
    FINE TUNING                                              raised or lowered by adjusting the pivot studs                The rotation torque of the arm can be                   assure no movement will occur. (E)
    Even after locking the locking nut, you can use          (B) that the tremolo mounts on. These are                     adjusted by raising the tremolo and
    located at either side of the front of the bridge.
    the fine tuners to make fine adjustments to the          Clockwise lowers the tremolo and counter                      inserting a 1.5mm Allen wrench in                        INTONATION ADJUSTMENT (FAT10/SAT10)
    tuning of each string. You should adjust all of          clockwise raises the tremolo.                                 the screw (A) on the tremolo block,                      The intonation can be adjusted by adjusting the saddle forward or
    the fine tuners (C) to the center of adjustable                                                                        Turning this screw clockwise will                        backward using a Phillips (+) head screwdriver on the intonation
    range before you lock the locking nut.   (G)                                                                           tighten the arm torque and turning                       adjustment screw at the rear of the bridge.
    (C)                                                                     the screw counter clockwise will    (A)
    ADJUSTING THE ACTION                                                                                                   loosen the arm torque.
    To adjust the entire tremolo unit up or down,            ADJUSTING THE INTONATION                     (C)
    use an Allen wrench to turn the stud bolt (E)            Loosen the Pressure pad screw (C) on the                      ADJUSTING THE STRING HEIGHT (SAT PRO)
    located at the left and right of the tremolo    (E)      locking nut and loosen the string to be adjusted.             To adjust the action of each
    unit. (This cannot be adjusted for each  (F)             Loosen the Saddle lock screws (D) on the saddle               string, use a 1.5 mm Allen          (C)
    individual string.)                                      to be adjusted and adjust the saddle forward or               wrench to turn the screw on the
    backward. Tighten the Saddle lock screw (D)                                                   (D)
    ADJUSTING THE INTONATION                                 and tune the string. After rechecking the                     saddle (C). The overall height
    can be adjusted on either side
    Loosen the Pressure pad screw (D) on the     (D)         intonation, tighten the Pressure pad screw (C).               of the SAT PRO tremolo unit. To
    locking nut and loosen the string to be adjusted.                                                                      adjust the height, use a 3 mm                (E)
    Loosen the Saddle lock screws (F) on the saddle          *On the base plate there are two holes for each Saddle lock screw. These allow the user to change string gauges         FAT10                    SAT10
    while allowing the maximum saddle movement. If the intonation cannot be adjusted because the saddle needs  Allen wrench to turn the stud (D)
    to be adjusted and adjust the saddle forward or          to be set back further, remove the intonation screw and insert it into the hole located further back on the bridge
    plate.                                                        located on either side of the                            ADJUSTING THE INTONATION &
    backward. Tighten the Saddle lock screw (F)                                                                            unit. Use caution when
    and tune the string. After rechecking the                                                                              adjusting the height of the entire tremolo unit; adjust both sides to the  THE STRING HEIGHT (FAT 6)
    intonation, tighten the Pressure pad screw (D).                                                                        same height to ensure optimum tremolo operation.         The intonation can be adjusted by
    *On the base plate there are two holes for each Saddle lock screw. These allow the user to change string gauges  REPLACING THE STRINGS                                          adjusting the saddle forward or
    while allowing thee maximum saddle movement. If the intonation cannot be adjusted because the saddle needs to  In the case of Lo-TRS II tremolo, replace the                    backward using a philips(+) head
    be set back further, remove the intonation screw and insert it into the hole located further back on the bridge plate.  ADJUSTING THE STRING HEIGHT (FAT20/FAT10/SAT10)
    strings one by one. Removing all the old strings              The height adjustment of the tremolo can be raised or lowered by  adjustment screw at the rear of the
    REPLACING THE STRINGS                                    at once will release the tension on the tremolo               adjusting the pivot studs (C) that the tremolo mounts on. These are  bridge. String height is controlled by
    In the case of EDGE III tremolo, replace the             and change the tremolo angle “up-pull.”                       located at either side of the front of the bridge. Clockwise lowers the  raising or lowering the small allen
    strings one by one. Removing all the old strings         Loosen the Pressure pad screw (C) on the                      tremolo and counter clockwise raises the tremolo.        screws using a wrench on either side
    at once will release the tension on the tremolo          locking nut and loosen the string to be                                                                                of the saddle.
    and change the tremolo angle “up-pull.” Loosen           replaced. Loosen the String stopper screw (E)                                                                          REPLACING THE STRINGS
    the Pressure pad screw (D) on the locking nut            and remove the string from the saddle. Cut off                    (C)                        (C)                       To replace strings, thread the new
    and loosen the string to be replaced. Loosen the         the ball end of new string as shown on the illustration and insert the cut                                             strings through the string holes
    String stopper screw (G) and remove the string           side of new string between the saddle and the String holder block .                                                    located on the back of the guitar. The
    from the saddle. Cut off the ball end of new             Tighten the String stopper screw (E) and tune the string. After checking                                               strings are then threaded through the
    string as shown on the illustration and insert the cut side of new string  the intonation, tighten the Pressure pad screw (C) on the locking nut.                               tremolo block and up and over the
    between the saddle and the String holder block.Tighten the String                                                                                                               saddle.
    stopper screw (G) and tune the string. After checking the intonation,
    tighten the Pressure pad screw (D) on the locking nut.   ILT                                                                                                                    FAT/SAT (expect FAT6)
    ADJUSTING THE TREMOLO SPRING
    EDGE III                                                 The tremolo springs adjust the                                                                                         ADJUSTING THE TREMOLO SPRING
    ADJUSTING THE TREMOLO SPRING                             tremolo angle by tightening or                                FAT20                       FAT10                        A standard tremolo can be adjusted
    The tremolo springs adjust the tremolo                   loosening the tremolo tension.  To                                                                                     so that the pitch can be raised when
    angle by tightening or loosening the                     adjust tremolo angle, locate the                                                                                       the tremolo arm is pulled up to
    tremolo tension. To adjust tremolo                       adjustment screws in the rear                                     (C)                                                  loosen the tremolo springs located
    angle, locate the adjustment screws in                   tremolo cavity. The tremolo system                                                                                     under the tremolo cavity on the back
    the rear tremolo cavity. The tremolo                     when in tune should sit parallel to                                                                                    of the guitar. One disadvantage of
    system when in tune should sit parallel                  the surface of the guitar as follows.                                                                                  this procedure is that it can cause
    to the surface of the guitar as follows.                 If the tremolo system is not sitting                                                                                   the pitch to go sharp if string breaks.
    If the tremolo system is not sitting parallel to the surface of the guitar,  parallel to the surface of the guitar, remove the tremolo cavity cover                             To remedy this, adjust the tremolo
    remove the tremolo cavity cover plate and tighten the Tremolo tension  plate and tighten the Tremolo tension adjustment screws if the tremolo                                   plate so it sits flush on the body by
    adjustment screws if the tremolo is forward dumped. Loosen the screws  is forward dumped. Loosen the screws if the tremolo is up-pulled.                                        tightening the tremolo springs.
    if the tremolo is up-pulled.Retune the                  Retune the strings to the proper pitch                                                            Choose the number and
    strings to the proper pitch and check the               and check the angle. Choose the number                                                            placement of the tremolo
    angle. Choose the number and placement                  and placement of the tremolo springs      SAT10                                                   springs according to the string
    of the tremolo springs according to the                 according to the string gauge and the                                                             gauge and the tremolo
    string gauge and the tremolo angle.                     tremolo angle.                                                                                    adjustment .                      FLOATING PARALLEL

Скачать инструкцию

Файл скачали 16 раз (Последний раз: 19 Сентября 2019 г., в 19:49)

Загрузить

Инструкции к похожим моделям