На сайте 124169 инструкций общим размером 502.7 Гб , которые состоят из 6277380 страниц
Руководство пользователя IBANEZ EDA Bass. Основные функции, характеристики и условия эксплуатации изложены на 2 страницах документа в pdf формате.
Доступно к просмотру 2 страницы. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.
EQ Controls The EQA-PZ system has separate EQ circuits for both the Magnetic Pickup and the Piezo Pickup. The Magnetic EQ Circuit boosts both the bass and treble frequencies simultaneously with a single control knob. The Piezo Pickup EQ Circuit is a 2-band EQ circuit and features a Treble EQ knob on the body and a Bass EQ trim pot inside the control cavity. The Bass EQ trim pot is designed for "set and forget" use. Turning the trim clockwise boosts the bass frequencies. Turning the trim Magnetic Volume INSTRUCTION MANUAL counterclockwise cuts the bass frequencies. Piezo Volume Piezo Treble Magnetic EQ Boost/Cut ® MONO-RAIL II w/Fishman Piezo Mono-Rail II w/Fishman® Piezo bridges allow the bass strings to be isolated fro one another by using independent bridge plates for each string. the strings are installed by lowering the ball end into the bridge and hooking the ball end below the string catch at the rear of the bridge. (A) Intonation adjustments can be made by adjusting the intonation screws (A) at the rear of the bridge clockwise to move the saddle back, and counter clockwise to move the saddle forward. This is to certify that the aforementioned equipments fully conform to protection requirements of the following EC council directives. DIRECTIVES : 89/336/EEC Electromagnetic compatibility Ibanez E D A Bass Printed in KOREA JAN01393 ©Copyright 2001
E Q A - P Z S y s t e m The EQA-PZ system was designed to allow bassists to achieve various sound Piezo Sensitivity Adjustments possibilities by combining a magnetic pickup with the FISHMAN® Piezo- The piezo pickup responds to individual string vibrations. However, different equipped Mono-Rail Bass Bridge. string gauges and player techniques can cause individual string outputs to sound uneven. To handle these variations, the EQA-PZ system allows the In addition to the Piezo Volume Knob and the Piezo Treble EQ Knob on the piezo pickup sensitivity for each string to be adjusted so string-to- string surface of the instrument, advanced adjustments can be fine-tuned by output levels can be properly balanced. utilizing the following trim pots located inside the control cavities: 1) Set the Piezo Volume Knob all the way up and the Piezo Treble EQ Knob to 1 Piezo Sensitivity Trims for individual string outputs. its center position. Internally adjust the Piezo Bass EQ trim 3 to the center. 2 Piezo Output Trim to balance the master piezo signal with the magnetic pickup. 2) Using a small screwdriver, adjust the 3 Piezo Bass EQ Trim. Piezo Sensitivity Trims 1 individually to (D) balance the output level of each string. 5-string 4-string 5B 4E 4E 3A 3) Turning the Trim Pot clockwise will 3A 2D 2D 1G increase the output level. Turning the 1G N/A Trim Pot counterclockwise decreases the output level. Note: If one string seems to have less output, adjust that string’s trim pot all the way up, then Center turn the rest of trims counterclockwise to balance the output level. 1 2 3 Balancing The Piezo Signal Output Level With The Magnetic Pickup. To utilize both the magnetic pickup and piezo pickup sounds, the piezo output level can be adjusted by a Trim Pot 2. 1) To determine output level of the Magnetic Pickup, set the Magnetic Pickup volume at 10, the Magnetic EQ at center and the Piezo Volume at 0. If needed, adjust the overall height of the Magnetic Pickup. 2) After the Magnetic Pickup height is determined, turn the Magnetic Pickup Volume back to 0 and the Piezo Volume up to 10, and then listen to the Battery output level balance of both pickups. The battery should be changed when the volume becomes low or the sound becomes distorted. Use a new 9-volt alkaline (not lithium or carbon) battery. 3) If the Magnetic Pickup output level is louder than the piezo, turn the Piezo The battery is stored inside control cavity (D). Inserting a plug into the jack Output Level Trim clockwise to increase the signal output level. To decrease activates the power supply. Be sure to disconnect the cord when the bass is the piezo signal output level, turn the trim pot counterclockwise. not in use; this will prevent the battery from draining.