Стиральная машина с сушкой INDESIT XWDA 751680X W EU. Инструкция на русском языке

Instructions for use
Washer-dryer
!     This symbol reminds you to read this          GB
instruction manual.
Contents
GB              ES              HU
Installation, 2-3
English,1       Espanol,13      Magyar,25
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
BG              CIS              UA                  Technical data
Care and maintenance, 4
Български,37    Русский,49      Українська,61
Cutting off the water or electricity supply
Cleaning the Washer-dryerCleaning the detergent dispen-
ser drawer
KZ                                                  Caring for the door and drum of your appliance
Cleaning the pump
?АЗА?ША,73                                            Checking the water inlet hose
Precautions and tips, 5
General safety
Load balancing system
Disposal
XWDA 751680                                           Description of the Washer-dryer and
starting a wash cycle, 6-7
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 8
Push&Wash+Dry
Table of wash cycles
Personalisation, 9
Setting the temperature
Setting the drying cycle
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Troubleshooting, 11
Service, 12
1

Installation
! This instruction manual should be kept in a         Levelling the machine correctly will provide
GB     safe place for future reference. If the Washer-       it with stability, help to avoid vibrations and
dryer is sold, transferred or moved, make sure        excessive noise and prevent it from shifting
that the instruction manual remains with the          while it is operating. If it is placed on carpet or
machine so that the new owner is able to fa-          a rug, adjust the feet in such a way as to allow
miliarise himself/herself with its operation and      a sufficient ventilation space underneath the
features.                                             Washer-dryer.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-   Connecting the electricity and
lation and operation of the appliance.                water supplies
Unpacking and levelling                               Connecting the water inlet hose
Unpacking                                                                       1. Connect the inlet
1. Remove the Washer-dryer from its packaging.                                  hose by screwing it
2. Make sure that the Washer-dryer has not                                      to a cold water tap
been damaged during the transportation                                          using a 3/4 gas thre-
process. If it has been damaged, contact the                                    aded connection (see
retailer and do not proceed any further with                                    figure).
the installation process.                                                       Before performing the
3. Remove the 4 pro-                                  connection, allow the
tective screws (used                                  water to run freely un-
during transportation)                                til it is perfectly clear.
and the rubber wa-
sher with the cor-
responding spacer,                                    2. Connect the inlet
located on the rear                                   hose to the Washer-
part of the appliance                                 dryer by screwing it
(see figure).                                         onto the correspon-
ding water inlet of the
4. Close off the holes using the plastic plugs                                  appliance, which is
provided.                                                                       situated on the top
5. Keep all the parts in a safe place: you will                                 right-hand side of the
need them again if the Washer-dryer needs to                                    rear part of the ap-
be moved to another location.                                                   pliance (see figure).
! Packaging materials should not be used as
toys for children.                                    3. Make sure that the hose is not folded over
or bent.
Levelling                                             ! The water pressure at the tap must fall within
1. Install the Washer-dryer on a flat sturdy flo-     the range of values indicated in the Technical
or, without resting it up against walls, furniture    data table (see next page).
cabinets or anything else.
2. If the floor is not      ! If the inlet hose is not long enough, contact a
perfectly level, com-       specialised shop or an authorised technician.
pensate for any une-
venness by tightening       ! Never use second-hand hoses.
or loosening the
adjustable front feet       ! Use the ones supplied with the machine.
(see figure); the angle
of inclination, measu-
red in relation to the
worktop, must not
exceed 2°.
2

Connecting the drain hose                            Warning! The company shall not be held re-          GB
sponsible in the event that these standards are
Connect the drain           not observed.
hose, without bending
it, to a drain duct or      The first wash cycle
a wall drain situated
between 65 and 100          Once the appliance has been installed, and
65 - 100 cm           cm from the floor;          before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle “Auto Clean” (see “Cleaning the
Washer-dryer”).
Technical data
alternatively, placed
it over the edge of a        Model            XWDA 751680
basin, sink or tub, fa-                       width 59.5 cm
stening the duct sup-        Dimensions       height 85 cm
plied to the tap (see                         depth 54 cm
figure). The free end
of the hose should                            from 1 to 7 kg for wash
not be underwater.           Capacity         programme
from 1 to 5 kg for the drying
programme
! We advise against the use of hose extensions;       Electrical       please refer to the technical
connections data plate fixed to the machine
if it is absolutely necessary, the extension must
have the same diameter as the original hose                            maximum pressure
and must not exceed 150 cm in length.                                  1 MPa (10 bar)
Water con-       minimum pressure
Electrical connections                                nections         0.05 MPa (0.5 bar)
drum capacity 52 litres
Before plugging the appliance into the electri-
city socket, make sure that:                          Spin speed       up to 1600 rotations per
•  the socket is earthed and complies with all                         minute
applicable laws;                                                       wash: programme 8; tem-
•  the socket is able to withstand the maximum                         perature 60°C; using a load
power load of the appliance as indicated in the                        of 7 kg.
Technical data table (see opposite);                  Energy ra-       drying: the smaller load
•  the power supply voltage falls within the va-      ted              (2kg) must be dried by se-
lues indicated in the Technical data table (see       programmes  lecting the “       ” dryness le-
opposite);                                            according to  vel. The load must consist of
•  the socket is compatible with the plug of the      regulation       2 sheets, 1 pillowcase and 2
Washer-dryer. If this is not the case, replace        EN 50229         hand towels; the remainder
the socket or the plug.                                                of the load must be dried by
! The Washer-dryer must not be installed ou-                           selecting the “   ” dryness
tdoors, even in covered areas. It is extremely                         level.
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.                             This appliance conforms to
! When the Washer-dryer has been installed,                            the following EC Directives:
the electricity socket must remain within easy                         - 2004/108/EC (Electroma-
reach.                                                                 gnetic Compatibility)
! Do not use extension cords or multiple sockets.                      - 2006/95/EC (Low Voltage)
! The cable should not be bent or compressed.                          - 2012/19/EU
! The power supply cable must only be repla-
ced by authorised technicians.
3