Стиральная машина INDESIT WITXL 1251. Инструкция на русском языке

Instructions for use
WASHING MACHINE
GB
Contents
GB            CZ               GR
Installation, 2-3
English, 1   Cesky 13          ????????, 25
Unpacking and levelling
Electric and water connections
The first wash cycle
ES            FR               UA                  Technical details
Espanol, 37   Francais, 49     Українська, 61       Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning your appliance
CIS                                                 Caring for your appliance door and drum
Cleaning the pump
РУССКИЙ,73                                          Checking the water inlet hose
Cleaning the detergent dispenser
Precautions and advice, 5
General safety
WITXL 1251                                          Disposal
Saving energy and respecting the environment
Washing machine description, 6-7
Control panel
How to open and shut the drum
Leds
Starting and Programmes, 8
Briefly: how to start a programme
Programme table
Personalisations, 9
Setting the temperature
Setting the spin cycle
Functions
Detergents and laundry, 10
Detergent dispenser
Bleach cycle
Preparing your laundry
Special items
Troubleshooting, 11
Service, 12
Before calling for Assistance
1

Installation
! Keep this instruction manual in a safe place for    If it is placed on a fitted or loose carpet, adjust
GB    future reference. Should the appliance be sold,       the feet in such a way as to allow enough room
transferred or moved, make sure the instruction       for ventilation beneath the washing machine.
manual accompanies the washing machine to
inform the new owner as to its operation and
features.                                             Electric and water connections
Connecting the water inlet hose
! Read these instructions carefully: they contain
vital information on installation, use and safety.                              1. Connect the supply
Unpacking and levelling                                                         pipe by screwing it to
a cold water tab using
a ? gas threaded con-
Unpacking                                                                       nection (see figure).
1. Unpack the washing machine.                                                  Before performing the
2. Check whether the washing machine has been                                   connection, allow the
damaged during transport. If this is the case, do                               water to run freely until
not install it and contact your retailer.                                       it is perfectly clear.
3. Remove the four pro-
tective screws and the
rubber washer with the                               2. Connect the other
respective spacer, si-                               end of the water inlet
tuated on the rear of the                            hose  to  the  washing
appliance (see figure).                              machine,
4. Seal the gaps using the                           screwing it onto the ap-
plastic plugs provided.                              pliance’s cold water in-
5. Keep all the parts: you                           let, situated on the top
will need them again if                              right-hand side on the
the  washing  machine                                rear of the appliance
needs to be moved to                                 (see figure).
another location.          3. Make sure there are no kinks or bends in the
Warning:  should  the      hose.
screws  be  re-used,
make sure you fasten       ! The water pressure at the tap must be within
the shorter ones at the top.                            the values indicated in the Technical details
! Packaging materials are not children’s toys.          table (on the next page).
Levelling                                             ! If  the  water  inlet  hose  is  not  long  enough,
contact  a  specialist  store  or  an  authorised
1. Install the washing machine on a flat sturdy         serviceman.
floor, without resting it up against walls, furniture   ! Never use hoses that have already been used.
cabinets or other.
2. If the floor is not per-
fectly level, compensate
for any unevenness by
tightening or loosening
the adjustable front feet
(see  figure);  the  angle
of  inclination,  measu-
red  according  to  the
worktop, must not ex-
ceed 2°.
Levelling your appliance
correctly will provide it with stability and avoid any
vibrations, noise and shifting during operation.
2

Connecting the drain hose                           ! Do not use extension cords or multiple sockets.
GB
Connect the drain          ! The cable should not be bent or compressed.
hose, without bending
it, to a drainage duct     ! The power supply cable must only be replaced
or a wall drain located    by authorised technicians.
at a height between
65 - 100 cm           65 and 100 cm from         Warning! The company shall not be held respon-
the floor;                 sible in the event that these regulations are not
respected.
The first wash cycle
alternatively, rest it on   Once the appliance has been installed, and be-
the side of a washba-      fore you use it for the first time, run a wash cycle
sin or bathtub, faste-     with detergent and no laundry, setting the 90°C
ning the duct sup-         programme without a pre-wash cycle.
plied to the tap (see
figure). The free end
of the hose should
not be underwater.          Technical details
Model           WITXL 1251
! We advise against the use of hose extensions;                      40 cm wide
if it is absolutely necessary, the extension must    Dimensions 85 cm high
have the same diameter as the original hose and                      60 cm deep
must not exceed 150 cm in length.
Capacity        from 1 to 6 kg
Electrical connections                                               Please refer to the technical
Before plugging the appliance into the electricity   Electric        data plate fixed to the ma-
socket, make sure that:                              connections     chine.
maximum pressure 1 MPa
• the socket is earthed and complies with all        Water           (10 bar) minimum pressure
applicable laws;                                    connections 0.05 MPa (0.5 bar) drum
capacity 42 litres
• the socket is able to withstand the maximum
power load of the appliance as indicated in the     Spin speed      up to 1200 rpm
Technical data table (see opposite);
Test wash
• the power supply voltage falls within the va-      cycles in
lues indicated in the Technical data table (see     accordan-       Programme      : Cotton stan-
opposite);                                          ce with         dard 60°C;
directives      Programme      : Cotton stan-
• the socket is compatible with the plug of the      1061/2010       dard 40°C.
washing machine. If this is not the case, repla-    and
ce the socket or the plug.                          1015/2010.
! The washing machine must not be installed                          This appliance is compliant
outdoors, even in covered areas. It is extremely                     with the following European
dangerous to leave the appliance exposed to                          Community Directives:
rain, storms and other weather conditions.                           - 2004/108/CEE (Electroma-
gnetic Compatibility)
! When the washing machine has been installed,                       - 2006/95/CE (Low Voltage)
the electricity socket must be within easy reach.                    - 2012/19/EU
3