Стиральная машина HOTPOINT-ARISTON RPD 1165 DX EU. Инструкция на русском языке

Instructions for use
WASHING MACHINE
Contents                                                 GB
Installation, 2-3
GB             ES              GR               Unpacking and levelling
Connecting the electricity and water supplies
English,1      Espanol,13      ????????,25       The first wash cycle
Technical data
Care and maintenance, 4
TR            BG              RU               Cutting off the water or electricity supply
Cleaning the washing machine
Turkce,37     Aueaa?nee,49    Русский,61        Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
RPD 1165 D                                       Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and functions, 9
Table of wash cycles
Wash functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
1

Installation
! This instruction manual should be kept in a         venness by tightening or loosening the adju-
GB      safe place for future reference. If the washing       stable front feet (see figure); the angle of incli-
machine is sold, transferred or moved, make           nation, measured in relation to the worktop,
sure that the instruction manual remains with         must not exceed 2°.
the machine so that the new owner is able to          Levelling the machine correctly will provide
familiarise himself/herself with its operation        it with stability, help to avoid vibrations and
and features.                                         excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
! Read these instructions carefully: they con-        a rug, adjust the feet in such a way as to allow
tain vital information relating to the safe instal-   a sufficient ventilation space underneath the
lation and operation of the appliance.                washing machine.
Connecting the electricity and
Unpacking and levelling                               water supplies
Unpacking                                             Connecting the water inlet hose
1. Remove the washing machine from its                                        1. Connect the inlet
packaging.                                                                    hose by screwing it to
2. Make sure that the washing machine has                                     a cold water tap using
not been damaged during the transportation                                    a 3/4 gas threaded
process. If it has been damaged, contact the                                  connection (see figu-
retailer and do not proceed any further with                                  re).
the installation process.                                                     Before performing the
connection, allow the
3. Remove the 4 pro-                                 water to run freely until
tective screws (used                                 it is perfectly clear.
during transportation)
and the rubber wa-                                    2. Connect the inlet
sher with the cor-                                    hose to the washing
responding spacer,                                    machine by screwing
located on the rear                                   it onto the correspon-
part of the appliance                                 ding water inlet of the
(see figure).                                         appliance, which is
situated on the top
4. Close off the holes using the plastic plugs                                 right-hand side of the
provided.                                                                      rear part of the ap-
5. Keep all the parts in a safe place: you will                                pliance (see figure).
need them again if the washing machine ne-
eds to be moved to another location.                  3. Make sure that the hose is not folded over
or bent.
! Packaging materials should not be used as
toys for children.                                    ! The water pressure at the tap must fall within
the range of values indicated in the Technical
Levelling                                             data table (see next page).
1. Install the washing       ! If the inlet hose is not long enough, contact a
machine on a flat            specialised shop or an authorised technician.
sturdy floor, without
resting it up against        ! Never use second-hand hoses.
walls, furniture cabi-
nets or anything else.       ! Use the ones supplied with the machine.
2. If the floor is not
perfectly level, com-
pensate for any une-
2

Connecting the drain hose                             ! Do not use extension cords or multiple so-
ckets.                                             GB
Connect the drain            ! The cable should not be bent or compressed.
hose, without bending        ! The power supply cable must only be repla-
it, to a drain duct or       ced by authorised technicians.
a wall drain situated
between 65 and 100
65 - 100 cm           cm from the floor;           Warning! The company shall not be held re-
sponsible in the event that these standards are
not observed.
The first wash cycle
Once the appliance has been installed, and
alternatively, placed        before you use it for the first time, run a wash
it over the edge of a        cycle with detergent and no laundry, using
basin, sink or tub, fa-      wash cycle auto clean (see “Cleaning the wa-
stening the duct sup-        shing machine”).
plied to the tap (see
figure). The free end        Technical data
of the hose should
not be underwater.           Model            RPD 1165 D
width 59.5 cm
! We advise against the use of hose extensions;       Dimensions       height 85 cm
if it is absolutely necessary, the extension must                      depth 60,5 cm
have the same diameter as the original hose
and must not exceed 150 cm in length.                 Capacity         from 1 to 11 kg
Electrical       please refer to the technical
Electrical connections                                connections      data plate fixed to the ma-
chine
Before plugging the appliance into the electri-                        maximum pressure
city socket, make sure that:                                           1 MPa (10 bar)
•  the socket is earthed and complies with all        Water con-       minimum pressure
applicable laws;                                      nections         0.05 MPa (0.5 bar)
drum capacity 71 litres
•  the socket is able to withstand the maxi-
mum power load of the appliance as indicated          Spin speed       up to 1600 rotations per
in the Technical data table (see opposite);                            minute
Test wash
•  the power supply voltage falls within the va-      cycles in        programme 9 ;
lues indicated in the Technical data table (see       accordance       Eco Cotton 60°C.
opposite);                                            with re-         programme 9 ;
gulations
•  the socket is compatible with the plug of the      1061/2010        Eco Cotton 40°C.
washing machine. If this is not the case, repla-      1015/2010
ce the socket or the plug.
This appliance conforms to
! The washing machine must not be installed                            the following EC Directives:
outdoors, even in covered areas. It is extreme-                        - 2004/108/EC (Electroma-
ly dangerous to leave the appliance exposed                            gnetic Compatibility)
to rain, storms and other weather conditions.                          - 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
! When the washing machine has been instal-
led, the electricity socket must remain within
easy reach.
3