Стиральная машина HOTPOINT-ARISTON ARTXF 149. Инструкция на русском языке

Instructions for use
WASHING MACHINE
Contents
GB
GB            CIS              PL                   Installation, 2-3
Unpacking and levelling
English,1      ???????? ??    Polski,25              Connecting the electricity and water supplies
The first wash cycle
Technical data
I              F                                   Description of the washing machine
and starting a wash cycle, 4-5
Italiano,37    Francais,49                           Control panel
Indicator lights
How to open and shut the drum
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
ARTXF 149                                            Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
How to clean the detergent dispenser
Troubleshooting, 11
Service, 12
1

Installation
GB      ! Keep this instruction manual in a safe place for future refe-  Putting your appliance in place and moving it.
rence. Should the appliance be sold, transferred or moved,                      If    your  washing  machine
make sure the instruction manual accompanies the washing                        is equipped with a special
machine to inform the new owner as to its operation and                         set  of  retractable  wheels
features.                                                                       you  can  easy  move  it.
To  lower  the  wheels  and
! Read these instructions carefully: they contain vital infor-                  thus  move  the  appliance
mation on installation, use and safety.                                         effortlessly,  just  pull  the
lever, situated on the left-
Unpacking and levelling                                                         hand  side  beneath  the
base. Once the appliance
Unpacking                                                                       is in the required position,
1.  Unpack  the  washing                              put the lever back in place.
machine.                                              The  washing  machine  is
2. Check whether the wa-
shing  machine  has  been   now firmly in place (see figure).
damaged during transport.   Electric and water connections
If this is the case, do not
install it and contact your   Connecting the water inlet hose
retailer.
3. Remove the four protec-                           1. Connect the supply pipe
tive screws and the rubber                           by screwing it to a cold water
washer with the respective                           tab using a ? gas threaded
spacer,  situated  on  the                           connection (see figure).
rear of the appliance (see                           Before performing the con-
figure).                                             nection, allow the water to
4. Seal the gaps using the                           run freely until it is perfectly
plastic plugs provided.                              clear.
5. Keep all the parts: you will need them again if the washing
machine needs to be moved to another location.
Warning: should the screws be re-used, make sure you fasten
2. Connect the other end of
the shorter ones at the top.                                                   the water inlet hose to the
! Packaging materials are not children’s toys.                                 washing machine, screwing
it onto the appliance’s cold
Levelling                                                                      water inlet, situated on the
Your machine may make a considerable amount of noise if                        top  right-hand  side  on  the
the two front feet have not been adjusted correctly.                           rear  of  the  appliance  (see
1.  Install  the  washing  ma-                        figure).
chine on a flat sturdy floor,
without resting it up against
walls,  furniture  cabinets  or
other.                      3. Make sure there are no kinks or bends in the hose.
2. If the floor is not perfectly   !  The  water  pressure  at  the  tap  must  be  within
level,  compensate  for  any   the  values  indicated  in  the  Technical  details  table
unevenness by tightening or   (on the next page).
loosening the adjustable front
feet (see figure); the angle of   !  If the water inlet hose is not long enough, contact a spe-
inclination, measured accor-  cialist store or an authorised serviceman.
ding to the worktop, must not exceed 2°.
Levelling your appliance correctly will provide it with stability
and avoid any vibrations, noise and shifting during operation.
If it is placed on a fitted or loose carpet, adjust the feet in
such a way as to allow enough room for ventilation beneath
the washing machine.
2

Connecting the drain hose                            ! Do not use extension cords or multiple sockets.    GB
Connect the drain hose,     ! The cable should not be bent or compressed.
without bending it, to a
drainage duct or a wall     ! The power supply cable must only be replaced by autho-
drain located at a height   rised technicians.
between 65 and 100 cm
65 - 100 cm           from the floor;             Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
alternatively, rest it on   Once the appliance has been installed, and before you use
the side of a washbasin     it for the first time, run a wash cycle with detergent and no
or bathtub, fastening the   laundry, using the wash cycle 2.
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is   Technical details
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.                                            Model           ARTXF 149
40 cm wide
Dimensions      85 cm high
Electrical connections
60 cm deep
Before plugging the appliance into the electricity socket,   Capacity  from 1 to 6 kg
make sure that:
Electric        Please refer to the technical data plate
• the socket is earthed and complies with all applicable   connections  fixed to the machine.
laws;
maximum pressure 1 MPa (10 bar)
Water
• the socket is able to withstand the maximum power load   connections  minimum pressure 0.05 MPa (0.5 bar)
of the appliance as indicated in the Technical data table            drum capacity 42 litres
(see opposite);
Spin speed      up to 1400 rpm
• the power supply voltage falls within the values indicated   Test wash
in the Technical data table (see opposite);          cycles in
accordance      programme 7; temperature 60°C and
• the socket is compatible with the plug of the washing   with directives  40°C.
machine. If this is not the case, replace the socket or the   1061/2010 and
plug.                                                1015/2010
! The washing machine must not be installed outdoors,                 This appliance is compliant with
even in covered areas. It is extremely dangerous to leave             the following European Community
the appliance exposed to rain, storms and other weather               Directives:
- 2004/108/CE (Electromagnetic
conditions.
Compatibility)
- 2006/95/CE (Low Voltage)
! When the washing machine has been installed, the elec-              - 2002/96/CE
tricity socket must be within easy reach.
3