Стиральная машина BEKO WMB 71031 PTM. Инструкция на русском языке

Washing Machine                                      WMB 71031 PTM
Стиральная машина
Lavadora

1  Important safety instructions        •   Never touch the plug with wet hands! Never
This section contains safety instructions that will   unplug by pulling on the cable, always pull out
help protect from risk of personal injury or property   by grabbing the plug.
damage. Failure to follow these instructions shall   •   Use detergents, softeners and supplements
void any warranty.                         suitable for automatic washing machines only.
General safety                          •   Follow the instructions on the textile tags and
on the detergent package.
•   8 years and older children and people with   •   The product must be unplugged during
reduced physical, sensory, and mental abilities   installation, maintenance, cleaning and
as well as unskilled or inexperienced persons   repairing procedures.
can use this appliance provided that they are   •   Always have the installation and repairing
supervised and instructed on safe use of the   procedures carried out by the Authorized
appliance as well as to the related dangers.   Service Agent. Manufacturer shall not be
Children should not play or tamper with the   held liable for damages that may arise from
appliance. Cleaning and user maintenance   procedures carried out by unauthorized
should never be performed by children unless   persons.
supervised by a responsible adult.
•   Never place the product on a carpet-covered   Intended use
floor; otherwise, lack of airflow beneath the   •   This product has been designed for domestic
machine will cause electrical parts to overheat.   use. It is not suitable for commercial use and it
This will cause problems with your product.  must not be used out of its intended use.
•   Do not operate the product if the power cable   •   The product must only be used for washing
/ plug is damaged. Call the Authorized Service   and rinsing of laundry that are marked
Agent.                                 accordingly.
•   Have a qualified electrician connect a   •   The manufacturer waives any responsibility
16-Ampere fuse to the installation location of   arisen from incorrect usage or transportation.
the product.                        Children's safety
•   If the product has a failure, it should not   •   Electrical products are dangerous for the
be operated unless it is repaired by the   children. Keep children away from the product
Authorized Service Agent. There is the risk of   when it is in use. Do not let them to tamper
electric shock!                        with the product. Use child lock to prevent
•   This product is designed to resume operating   children from intervening with the product.
in the event of powering on after a power   •   Do not forget to close the loading door when
interruption. If you wish to cancel the   leaving the room where the product is located.
programme, see "Cancelling the programme"   •   Store all detergents and additives in a safe
section.                               place away from the reach of the children.
•   Connect the product to a grounded outlet
protected by a fuse complying with the values  2  Installation
in the "Technical specifications" table. Do not   Refer to the nearest Authorised Service Agent for
neglect to have the grounding installation   installation of the product. To make the product
made by a qualified electrician. Our company   ready for use, review the information in the user
shall not be liable for any damages that   manual and make sure that the electricity, tap
will arise when the product is used without   water supply and water drainage systems are
grounding in accordance with the local   appropriate before calling the Authorized Service
regulations.                        Agent. If they are not, call a qualified technician
•   The water supply and draining hoses must be  and plumber to have any necessary arrangements
securely fastened and remain undamaged.   carried out.
Otherwise, there is the risk of water leakage.  C   Preparation of the location and electrical,
•   Never open the loading door or remove the   tap water and waste water installations at
filter while there is still water in the drum.   the place of installation is under customer's
Otherwise, risk of flooding and injury from hot   responsibility.
water will occur.                       Installation and electrical connections of the
•   Do not force open the locked loading door.   B  product must be carried out by the Authorized
The loading door will be ready to open just a   Service Agent. Manufacturer shall not be
few minutes after the washing cycle comes to   held liable for damages that may arise from
an end. In case of forcing the loading door to   procedures carried out by unauthorized
open, the door and the lock mechanism may   persons.
get damaged.                            Prior to installation, visually check if the
•   Unplug the product when not in use.  A  product has any defects on it. If so, do not
•   Never wash the product by spreading or   have it installed. Damaged products cause
pouring water onto it! There is the risk of   risks for your safety.
electric shock!
2   EN

C    Make sure that the water inlet and discharge   C   If you want to use both water inlets of the
hoses as well as the power cable are not   product, connect the hot water hose after
folded, pinched or crushed while pushing   removing the stopper and gasket group from
the product into its place after installation or   the hot water valve. (Applies for the products
cleaning procedures.                   supplied with a blind stopper group.)
Appropriate installation location       A   Models with a single water inlet should not
•   Place the machine on a rigid floor. Do not   be connected to the hot water tap. In such
place it on a long pile rug or similar surfaces.  a case the laundry will get damaged or the
•   Total weight of the washing machine and the   product will switch to protection mode and will
dryer -with full load- when they are placed   not operate.
on top of each other reaches to approx.   A   Do not use old or used water inlet hoses on
180 kilograms. Place the product on a solid   the new product. It may cause stains on your
and flat floor that has sufficient load carrying   laundry.
capacity!                           1.  Connect the special hoses supplied with the
•   Do not place the product on the power cable.  product to the water inlets on the product.
•   Do not install the product at places where   Red hose (left) (max. 90 ?C) is for hot water
temperature may fall below 0?C.        inlet, blue hose (right) (max. 25 ?C) is for cold
•   Place the product at least 1 cm away from the   water inlet.
edges of other furniture.
Removing packaging reinforcement
Tilt the machine backwards to remove the
packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Removing the transportation locks
A    Do not remove the transportation locks before
taking out the packaging reinforcement.
A    Remove the transportation safety bolts before
operating the washing machine, otherwise,
the product will be damaged.
1.  Loosen all the bolts with a spanner until they   A   Ensure that the cold and hot water
rotate freely (C).                     connections are made correctly when
2.  Remove transportation safety bolts by turning   installing the product. Otherwise, your laundry
them gently.                           will come out hot at the end of the washing
3.  Attach the plastic covers supplied in the User   process and wear out.
Manual bag into the holes on the rear panel.   2.  Tighten all hose nuts by hand. Never use a
(P)                                    wrench when tightening the nuts.
C    Keep the transportation safety bolts in a safe
place to reuse when the washing machine
needs to be moved again in the future.
C    Never move the product without the
transportation safety bolts properly fixed in   3.  Open the taps completely after making the
place!                                 hose connection to check for water leaks at
Connecting water supply                    the connection points. If any leaks occur, turn
C    The water supply pressure required to run   off the tap and remove the nut. Retighten
the product is between 1 to 10 bars (0.1 – 10   the nut carefully after checking the seal. To
MPa). It is necessary to have 10 – 80 liters of   prevent water leakages and damages caused
water flowing from the fully open tap in one   by them, keep the taps closed when the
minute to have your machine run smoothly.   machine is not in use.
Attach a pressure reducing valve if water   Connecting to the drain
pressure is higher.                 •   The end of the drain hose must be directly
C    If you are going to use the double water-inlet   connected to the wastewater drain or to the
product as a single (cold) water-inlet unit, you   washbasin.
must install the supplied stopper to the hot   A   Your house will be flooded if the hose comes
water valve before operating the product.   out of its housing during water discharge.
(Applies for the products supplied with a blind   Moreover, there is risk of scalding due to
stopper group.)                        high washing temperatures! To prevent such
3   EN