Посудомоечная машина HOTPOINT-ARISTON CIS LI 470 A. Инструкция на русском языке

"
.
/             0
Positioning and levelling
 +
Connecting the water and electricity supplies
Technical data
Overall view
Control panel


  !
Lower rack
Cutlery basket
Upper rack
""
      #
Starting the dishwasher
Loading the detergent
Washing options*
%,
$
 %
Wash cycle table



       &
Loading the rinse aid
Loading the refined salt

'

 (
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the filters
Leaving the machine unused for extended periods
)
"
*
 +,
General safety
Disposal
Saving energy and respecting the environment
-
".

       ++

      +
Before calling for Assistance

Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given away or
/
moved, please ensure the manual is kept with the
machine, so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully: it
contains important information regarding the safe
installation, use and maintenance of the appliance.
If the appliance must be moved at any time, keep it

1
in an upright position; if absolutely necessary, it may be
tilted onto its back.                               •  To a suitable cold water connection point: before
attaching the hose, run the water until it is perfectly
clear so that any impurities that may be present in the
)


*
water do not clog the appliance; after performing this
1. Remove the appliance from all packaging and check   operation, screw the inlet hose tightly onto a tap with
that it has not been damaged during transportation.    a ? gas threaded connection.
If it has been damaged, contact the retailer and do not  •  To a suitable hot water connection point: your
proceed any further with the installation process.     dishwasher may be provided with hot water from the
mains supply (if you have a central heating system
2. Check the dishwasher by placing it so that its sides or
with radiators) provided that it does not exceed a
back panel are in contact with the adjacent cabinets or
temperature of 60°C.
even with the wall. This appliance can also be recessed
Screw the hose to the tap as described for
under a single worktop* (see the Assembly instruction
connection to a cold water supply.
sheet).
3. Position the dishwasher on a level and sturdy floor. If   If the inlet hose is not long enough, contact a
the floor is uneven, the front feet of the appliance may be  specialist store or an authorised technician (see
adjusted until it reaches a horizontal position (the angle of  Assistance).
inclination must not exceed 2 degrees). If the appliance is
The water pressure must be within the values
levelled correctly, it will be more stable and much less
indicated in the Technical data table (see below).
likely to move or cause vibrations and noise while it is
operating.                                              The hose should not be bent or compressed.
4. Adjust the height of the rear feet from the front of the
appliance*: use a screwdriver to tighten or loosen the
screws on the lower part of the dishwasher.
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the

1


$
water supply in the event of anomalies or leaks from
"
inside the appliance.
Connection to the water and electricity supplies
- is provided with a Water Stop* safety device, in other
should only be performed by a qualified technician.
words it has a water inlet hose that consists of a
transparent hose on the outside and a red hose on the
The dishwasher should not stand on top of the water
inside: both the hoses can withstand extremely high
hoses or the electricity supply cable.
pressure. If the internal hose breaks, the external hose
becomes a bright red colour and carries the water
The appliance must be connected to the water
instead, thus avoiding any leakage.
supply network using new piping.
- Do not use old piping.
It is very important to check the external hose
regularly: if it is a bright red colour, it must be replaced
The water inlet (A) and outlet (B) hoses and the
by an authorised technician as soon as possible (see
electricity supply cable may be positioned towards the
Assistance).
right or the left in order to achieve the best possible
installation (see figure).                               //234
5065-27
Under no circumstance should the water inlet hose be
cut as it contains live electrical parts.
* Only available in selected models.


1

"


*


1$
After the appliance has been installed, immediately  /
Connect the outlet hose (without bending it) to a drain  before running the first wash cycle, completely fill the
duct with a minimum diameter of 4 cm. Alternatively, rest  salt dispenser with water and add approximately 2 kg of
it over a sink or tub; the free end of the hose should not  salt (see Rinse aid and refined salt). The water may
remain immersed in water.                            overflow: this is normal and is not a cause for concern.
It is also normal that the LOW SALT* indicator light
The special plastic elbow*   continues to flash for a few cycles after the salt has been
A
makes it easier to find the  loaded.
best layout: fix the elbow to
the wall securely in order to  


 8
prevent the outlet hose from  After installing the dishwasher, open the door and stick
moving and spilling the dirty  the adhesive transparent strip under the wooden shelf in
water.                       order to protect it from any condensation that may form.
The part of the hose marked
with the letter A should be
between 40 and 100 cm
above the ground (see
figure).
-
We advise against the use of hose extensions.
width 44.5 cm
Dimensions       height 82 cm
Before inserting the plug into the electrical socket, make
depth 57 cm
sure that:
Capacity         9 standard place-settings
•  the socket is earthed and complies with current
regulations;                                       Water supply     0,05 ? 1MPa (0.5 ? 10 bar)
pressure         4.3 psi – 145 psi
•  the socket can withstand the maximum load of the
Power supply
appliance, which is indicated on the data plate                     See appliance data plate
voltage
located on the inside of the door (see Description of
the appliance);                                    Total absorbed   See appliance data plate
power
•  the power supply voltage falls within the values
Fuse             See appliance data plate
indicated on the data plate on the inside of the door;
•  the socket is compatible with the plug of the                       This dishwasher conforms to
appliance. If this is not the case, ask an authorised               the following European
Community Directives:
technician to replace the plug (see Assistance); do
-73/23/EEC dated 19/02/73
not use extension cables or multiple sockets.
(Low Voltage) and subsequent
modifications
Once the appliance has been installed, the                          -89/336/EEC dated 03/05/89
power supply cable, the electrical plug and socket                     (Electromagnetic Compatibility)
should remain accessible.                                              and subsequent modifications
-97/17/EC (Labelling)
If the power supply cable is damaged, it must                       -2002/96/ CE (Waste
be replaced by the manufacturer or its Technical                       Electrical and Electronic
Assistance Service in order to prevent all potential                   Equipment WEEE)
hazards. (See Assistance)
The cable should not be bent or compressed.
The Company shall not be held responsible for
any incidents that occur if these regulations are not
observed.
* Only available in selected models.