Посудомоечная машина HOTPOINT-ARISTON CIS LI 460 A. Инструкция на русском языке

"
.
/
0
Positioning and levelling
 +
Connecting the water and electricity supplies
Technical data
Overall view
Control panel


  !
Lower rack
Cutlery basket
Upper rack
""
      #
Starting the dishwasher
Loading the detergent
Washing options*
#,
$
 %
Wash cycle table



       &
Loading the rinse aid
Loading the refined salt

'

 (
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the filters
Leaving the machine unused for extended periods
)
"
*
 +,
General safety
Disposal
Saving energy and respecting the environment
-
".

       ++

      +
Before calling for Assistance

Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given away or
/
moved, please ensure the manual is kept with the
machine, so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully: it
contains important information regarding the safe
installation, use and maintenance of the appliance.

1
If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be
•  To a suitable cold water connection point: before
tilted onto its back.
attaching the hose, run the water until it is perfectly
clear so that any impurities that may be present in the
)


*
                              water do not clog the appliance; after performing this
operation, screw the inlet hose tightly onto a tap with
1. Remove the appliance from all packaging and check   a ? gas threaded connection.
that it has not been damaged during transportation.  •  To a suitable hot water connection point: your
If it has been damaged, contact the retailer and do not  dishwasher may be provided with hot water from the
proceed any further with the installation process.     mains supply (if you have a central heating system
2. Check the dishwasher by placing it so that its sides or  with radiators) provided that it does not exceed a
temperature of 60°C.
back panel are in contact with the adjacent cabinets or
Screw the hose to the tap as described for
even with the wall. This appliance can also be recessed
connection to a cold water supply.
under a single worktop* (see the Assembly instruction
sheet).
If the inlet hose is not long enough, contact a
3. Position the dishwasher on a level and sturdy floor. If  specialist store or an authorised technician (see
the floor is uneven, the front feet of the appliance may be  Assistance).
adjusted until it reaches a horizontal position (the angle of
inclination must not exceed 2 degrees). If the appliance is   The water pressure must be within the values
levelled correctly, it will be more stable and much less  indicated in the Technical data table (see below).
likely to move or cause vibrations and noise while it is
operating.                                              The hose should not be bent or compressed.
4. Adjust the height of the rear feet from the front of the
appliance*: use a screwdriver to tighten or loosen the
screws on the lower part of the dishwasher.
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the

1


$
water supply in the event of anomalies or leaks from
"
inside the appliance.
Connection to the water and electricity supplies  - is provided with a Water Stop* safety device, in other
should only be performed by a qualified technician.  words it has a water inlet hose that consists of a
transparent hose on the outside and a red hose on the
The dishwasher should not stand on top of the water  inside: both the hoses can withstand extremely high
hoses or the electricity supply cable.              pressure. If the internal hose breaks, the external hose
becomes a bright red colour and carries the water
The appliance must be connected to the water     instead, thus avoiding any leakage.
supply network using new piping.
It is very important to check the external hose
- Do not use old piping.
regularly: if it is a bright red colour, it must be replaced
by an authorised technician as soon as possible (see
The water inlet (A) and outlet (B) hoses and the
Assistance).
electricity supply cable may be positioned towards the
right or the left in order to achieve the best possible
installation (see figure).                               //234
5065-27
Under no circumstance should the water inlet hose be cut as it
contains live electrical parts.
* Only available in selected models.


1

"


*


1$
After the appliance has been installed, immediately  /
Connect the outlet hose (without bending it) to a drain  before running the first wash cycle, completely fill the
duct with a minimum diameter of 4 cm. Alternatively, rest  salt dispenser with water and add approximately 2 kg of
it over a sink or tub; the free end of the hose should not  salt (see Rinse aid and refined salt). The water may
remain immersed in water.                            overflow: this is normal and is not a cause for concern.
It is also normal that the LOW SALT* indicator light
The special plastic elbow*
A                                continues to flash for a few cycles after the salt has been
makes it easier to find the
loaded.
best layout: fix the elbow to
the wall securely in order to
prevent the outlet hose from  


 8
After installing the dishwasher, open the door and stick
moving and spilling the dirty
the adhesive transparent strip under the wooden shelf in
water.
order to protect it from any condensation that may form.
The part of the hose marked
with the letter A should be
between 40 and 100 cm
above the ground (see
figure).                                             -
We advise against the use of hose extensions.
width 44.5 cm
Before inserting the plug into the electrical socket, make  Dimensions   height 82 cm
sure that:                                                             depth 57 cm
Capacity         9 standard place-settings
•  the socket is earthed and complies with current
regulations;
Water supply     0,05 ? 1MPa (0.5 ? 10 bar)
pressure         4.3 psi – 145 psi
•  the socket can withstand the maximum load of the
appliance, which is indicated on the data plate    Power supply     See appliance data plate
located on the inside of the door (see Description of  voltage
the appliance);                                    Total absorbed
power            See appliance data plate
•  the power supply voltage falls within the values
indicated on the data plate on the inside of the door;  Fuse        See appliance data plate
•  the socket is compatible with the plug of the
This dishwasher conforms to
appliance. If this is not the case, ask an authorised               the following European
technician to replace the plug (see Assistance); do                 Community Directives:
not use extension cables or multiple sockets.                       -73/23/EEC dated 19/02/73
(Low Voltage) and subsequent
Once the appliance has been installed, the                          modifications
-89/336/EEC dated 03/05/89
power supply cable, the electrical plug and socket
(Electromagnetic Compatibility)
should remain accessible.
and subsequent modifications
-97/17/EC (Labelling)
If the power supply cable is damaged, it must                       -2002/96/ CE (Waste
be replaced by the manufacturer or its Technical
Electrical and Electronic
Assistance Service in order to prevent all potential
Equipment WEEE)
hazards. (See Assistance)
The cable should not be bent or compressed.
The Company shall not be held responsible for
any incidents that occur if these regulations are not
observed.
* Only available in selected models.