Газовая варочная поверхность WHIRLPOOL AKR 351/IX. Инструкция на русском языке

BUILT-IN GAS HOB INSTRUCTIONS
GB
-  In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood
IMPORTANT SAFETY INSTRUCTIONS                                                                    extraction speed).
-  After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve.
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT                                        -  Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat, oil or alcohol (e.g. rum,
This manual and the appliance itself provide important safety messages, to be read and observed at all times.  cognac, wine).
This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.  -  Keep the packaging materials out of the reach of children.
All safety messages will follow the safety alert symbol and either the terms:            -  Before cleaning or maintenance wait for hob to cool down.
Indicates a hazardous situation which, if not avoided, will cause serious injury.                      SAVE THESE INSTRUCTIONS
DANGER
Indicates a hazardous situation which, if not avoided, could cause serious injury.
WARNING                                                                                   INSTALLATION
All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what   After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the
can happen if the instructions are not followed.                                               dealer or your nearest After-sales Service.
-  The appliance must be disconnected from the power supply before carrying out any installation work.  These instructions are only valid for the countries whose symbols is given on the data plate (under the hob).
-  Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer’s   TECHNICAL INFORMATION FOR THE INSTALLER
instructions and local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in   •  This product can be embedded in a worktop 20 to 50 mm thick.
the user manual.
•  If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the
If the information in this manual is not followed exactly, a fire or explosion may result   work surface. This panel, that has to close completely the cutout in order to avoid any contact with the bottom
WARNING           causing property damage or injury.                                        part of the hob, must be positioned at a maximum distance of 150 mm below the upper surface of the work
surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven
-  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance.
beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The
What to do if you smell gas:                                                                    manufacturer declines all liability if another brand oven is installed beneath the hob.
-  Do not try to light any appliance.                                                         •  Before installation, make sure that:
-  Do not touch any electrical switch.                                                          -  the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the
-  Do not use any phone in your building.                                                          rating plate and injector table);
-  Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.  -  the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;
-  If you cannot reach your gas supplier, call the fire department.                             -  this appliance is not connected to a fume exhaust device. It shall be installed in accordance with current installation
-  Installation and service must be performed by a qualified installer, service agency or the gas supplier.  regulations. Particular attention shall be given to the relevant requirements regarding ventilation;
-  Use appliance in well ventilated rooms only.                                                 -  combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans.
GAS CONNECTION
The electrical and gas connections must comply with local regulations.
-  When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm, that provides   This operation must be performed by a qualified technician.
full disconnection.                                                                              WARNING
-  Regulations require that the appliance is grounded.
-  The power cable must be long enough for connecting the appliance, once fitted in its housing, to the power supply  •  The gas supply system must comply with local regulations.
-  Use only flexible or rigid metal hose for gas connection.                                   •  You can find specific local regulations for some countries in the paragraph
-  If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics   “Reference to Local Regulations”. If no information concerning your Country
to the original supplied by manufacturer (type H05V2V2-F 90°C or H05RR-F). This operation must be performed by a   is given, please ask details to your Installer.
qualified electrician.                                                                      •  The connection of the hob to the gas pipe network or gas cylinder must be
-  The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from   made by means of a rigid copper or steel pipe with fittings complying with
failure to comply with these requirements.                                                     local regulations, or by means of a continuous-surface stainless steel hose
-  Do not use multiple plug adapters or extension cords.                                          complying with local regulations. Interpose gasket (B) in the elbow
-  Do not pull the power supply cord in order to unplug the appliance.                            connection.The maximum length of the hose is 2 m.
-  The electrical components must not be accessible to the user after installation.            •  FOR BELGIUM ONLY: It is necessary to replace the elbow connection (A) on
-  Do not touch the appliance with any wet part of the body and do not operate it when barefoot.  the appliance, with the one supplied (if present).
-  This hob (class 3) is designed solely for private household use for cooking food. Do not use this appliance as a space   IMPORTANT: if a stainless steel hose is used, it must be installed so as not to
heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the hob. The   touch any mobile part of the furniture. It must pass through an area where
Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.  there are no obstructions and where it is possible to inspect it on all its
-  The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental   length.
capabilities, or with lack of experience and knowledge of the appliance, unless supervised or previously instructed in its   •  After connection to the gas supply, check for leaks with soapy water. Light
use by those responsible for their safety.
(Apply the label from warranty here)
-  Young children should be kept away from the appliance and supervised to ensure that they do not play with it.  up the burners and turn the knobs from max position   to minimum
-  The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or install an   position   to check flame stability.
extractor hood with exhaust duct.
5019 619 01574                                                 Manufacturer: Whirlpool Europe S.r.l. Viale G. Borghi, 27 21025 Comerio (VA) ITALY

ELECTRICAL CONNECTION                                                                          REPLACING THE INJECTORS (see the injector table in the Instruction)
This operation must be performed by a qualified technician.             •  Remove grids (A).
WARNING
•  Extract  burners  (B).
•  The electrical connections must comply                               •  Using a socket spanner of the appropriate size unscrew
WARNING                                                                   L
with local regulations.                                                 the injector (C), unscrew the injector to be replaced.
•  The earthing of this appliance is                    Earth           •  Replace it with the injector suitable for the new type of
compulsory by law.                                   (yellow/green)     gas.
•  Do not use an extension cord.                                        •  Re-assemble the injector in (D).
N               •  If you have a multiple crown burner use side spanner to
replace the injector (E).
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.  Before installing the hob, remember to affix the gas
ASSEMBLY                                                                                       calibration plate supplied with the injectors in such a way
that it covers the existing information relating to gas
After having cleaned the perimeter surface,                                                    calibration.
apply the supplied gasket to the hob as shown
in the figure.
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted, remove the knob and
proceed as follows:
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
•  tighten screw to reduce the flame height (-);
NOTE: the power supply cable must be long enough to permit its upward extraction.
•  loosen screw to increase the flame height (+).
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and
The adjustment must be performed with the tap in minimum gas setting position (small
fasten them by means of their screws in accordance with the thickness of the worktop (see the following figures).
flame) .
•  The primary air of the burners does not need to be adjusted.
Top 30-50 mm
•  At this stage, light up the burners and turn the knobs from max position   to
minimum position   to check flame stability.
Top 20 mm
Upon completion of adjustment, reseal using sealing wax or an equivalent material.
REFERENCE TO LOCAL REGULATIONS
Ensure that the installation and gas connections are performed by a qualified technician, following the manufacturer's
instructions and in compliance with current local safety regulations.
AFTER-SALES SERVICE
Before calling the After-Sales Service, make sure you can give the following information:
ADJUSTMENT TO DIFFERENT TYPES OF GAS                                                           -  type of fault or problem;
This operation must be performed by a qualified technician.             -  exact model (written on the label affixed to the instruction/warranty);
WARNING                                                                                   -  service number that follows the word SERVICE on the rating plate under the hob and
on the label affixed to instruction/warranty;
If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label   -  your complete address and phone number.
on the top of the hob, change the injectors.                                                   If any repairs are required, please contact an authorised After-Sales Service, as indicated in
Remove the information label and keep it with the instructions booklet.                        the warranty.
Use pressure regulators suitable for the gas pressure indicated in the Instruction.
•  The gas nozzles must be changed by After Sales Service or a qualified technician.
•  Nozzles not supplied with the appliance must be ordered from After Sales Service.
•  Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will
go.
IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service for
the replacement of the burner tap if found to be faulty.

TROUBLESHOOTING GUIDE
If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine   DECLARATION OF CONFORMITY
the problem.                                                                                   •  This hob has been designed, constructed and marketed in compliance with:
1. The burner fails to ignite or the flame is not even                                           -  safety requirements of “Gas” Directive 2009/142/EC (ex: EEC 90/396);
Check that:                                                                                   -  safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent
•  The gas or electrical supplies are not shut off and especially that the gas supply tap is open.  amendments);
•  The gas cylinder (liquid gas) is not empty.                                                -  protection requirements of EEC Directive “EMC” 2004/108/EC;
•  The burner openings are not clogged.                                                     •  This hob is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. 1935/2004.
•  The plug end is not dirty.
•  All the burner parts have been positioned correctly.                                     SAFEGUARDING THE ENVIRONMENT
•  There are no draughts near the hob.
2. The burner does not stay lit                                                                Disposal of packing material
Check that:                                                                                 The packing material is 100% recyclable and is marked with the recycle symbol (  ). The various parts of the packing must
•  When lighting the burner, the knob has been pressed for enough time to activate the protection device.  therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
•  The burner openings are not clogged near the thermocouple.
•  The end of the safety device is not dirty.                                               Scrapping the product
•  The minimum gas setting is correct (see relevant paragraph).                             -  This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment
3. The containers are not stable                                                                 (WEEE).
Check that:                                                                                 -  By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
•  The bottom of the container is perfectly flat                                              environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
•  The container is centered on the burner.                                                 -  The symbol    on the product or on the accompanying documentation indicates that it should not be treated as
•  The grids have not been exchanged or positioned incorrectly.                               domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.
equipment.
CLEANING THE HOB SURFACE
Disconnect power before servicing.                                      PRODUCT DESCRIPTION
WARNING
•  All the enamelled and glass parts should be cleaned with warm water and neutral solution.
•  Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long. Any
food spills (water, sauce, coffee, etc.) should be wiped away before they dry.
•  Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with
specific cleaners for stainless steel surfaces.
NOTE: clean stainless steel only with soft cloth or sponge.
•  Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.
•  Do not use steam cleaning appliances.
•  Do not use flammable products.
•  Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.
CLEANING THE HOB PARTS
•  Grids, burner caps and burners can be removed to be cleaned.
•  Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none
of the burner openings is clogged.
•  Rinse  and  dry
•  Refit burners and burner caps correctly in the respective housings.
1. Removable panstand grids          Symbols
•  When replacing the grids, make sure that the panstand area is aligned with the burner.
•  Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to   2. Semi-rapid burner  Shaded circle  Tap closed
ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any baked-on
3. Semi-rapid burner                 Large flame           Maximum opening/delivery
food should be removed with a toothpick or needle.
NOTE: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing.  4. Rapid burner  Small flame           Minimum opening or reduced delivery
5. Auxiliary burner
6. Control knobs
The symbols          are indicating which cooking field this knob activates.
Note: your hob aesthetics can be slightly different from the drawing. Burner placement and control symbols can vary.