Газовая плита INDESIT I5GG0.1(W)/RU. Инструкция на русском языке

Operating Instructions
COOKER
GB
Contents
GB            RU            KZ
Installation, 2-5
English, 1    РУССКИЙ, 13 ?аза?ша?аза?ша ,27       Positioning and levelling
Electrical connections
Gas connection
Adapting to different types of gas
Technical  data
Table of burner and nozzle specifications
Description of the appliance, 6
Overall view
Control panel
I5GG0G RU
I5GG10G RU                                      Start-up and use, 7-9
Using the hob
MVI5G11 /RU
Using the oven
MVI5G1 /RU
I5GG0.1 RU                                      Oven cooking advice table
Precautions and tips, 10
General safety
Disposal
Respecting and conserving the environment
Maintenance and care, 11
Switching the appliance off
Cleaning the appliance
Gas tap maintenance
Replacing the oven light bulb
Assistance

Installation
! Before operating your new appliance please read   Disposing of combustion fumes
this instruction booklet carefully. It contains                                                         GB
important information concerning the safe installation  The disposal of combustion fumes should be
and operation of the appliance.                     guaranteed using a hood connected to a safe and
! Please keep these operating instructions for future  efficient natural suction chimney, or using an electric
reference. Make sure that the instructions are kept  fan that begins to operate automatically every time
with the appliance if it is sold, given away or moved.  the appliance is switched on (see figure).
! The appliance must be installed by a qualified
professional according to the instructions provided.
! Any necessary adjustment or maintenance must be
performed after the cooker has been disconnected
from the electricity supply.
! We recommend cleaning the oven before using it
for the first time, following the instructions provided
in the "Care and maintenance" section.
Room ventilation                                    Fumes channelled        Fumes channelled through
straight outside        a chimney or branched
The appliance may only be installed in permanently-                         flue system  reserved for
ventilated rooms, according to current national                             cooking appliances)
legislation. The room in which the appliance is     ! The liquefied petroleum gases are heavier than air
installed must be ventilated adequately so as to    and collect by the floor, therefore all rooms
provide as much air as is needed by the normal gas  containing LPG cylinders must have openings
combustion process (the flow of air must not be     leading outside so that any leaked gas can escape
3
lower than 2 m /h per kW of installed power).       easily.
The air inlets, protected by grilles, should have a  LPG cylinders, therefore, whether partially or
duct with an inner cross section of at least 100 cm 2  completely full, must not be installed or stored in
and should be positioned so that they are not liable  rooms or storage areas that are below ground level
to even partial obstruction (see figure A).         (cellars, etc.). Only the
These inlets should be enlarged by 100% - with a    cylinder being used should be stored in the room;
minimum of 200 cm  - whenever the surface of the    this should also be kept well away from sources
2
hob is not equipped with a flame failure safety     of heat (ovens, chimneys, stoves) that may cause
device. When the flow of air is provided in an      the temperature of the cylinder to rise above 50°C.
indirect manner from adjacent rooms (see figure B),
provided that these are not communal parts of a     Positioning and levelling
building, areas with increased fire hazards or
bedrooms, the inlets should be fitted with a        ! It is possible to install the appliance alongside
ventilation duct leading outside as described above.  cupboards whose height does not exceed that of the
Adjacent room  Room requiring  hob surface.
ventilation
A                     B
! Make sure that the wall in contact with the back of
the appliance is made from a non-flammable, heat-
resistant material (T 90°C).
To install the appliance correctly:
A                                       • Place it in the kitchen, dining room or the bed-sit
(not in the bathroom).
Ventilation opening for  Increase in the gap between  • If the top of the hob is higher than the cupboards,
comburent air         the door and the flooring       the appliance must be installed at least 200 mm
away from them.
! After prolonged use of the appliance, it is       • If the cooker is installed underneath a wall cabinet,
advisable to open a window or increase the speed of   there must be a minimum distance of 420 mm
any fans used.                                        between this cabinet and the top of the hob.
This distance should be increased to 700 mm if
the wall cabinets are flammable (see figure).
2

! Once the appliance has been installed, the power
• Do not position         supply cable and the electrical socket must be
GB
HOOD            blinds behind the         easily accessible.
cooker or less than 200   ! The cable must not be bent or compressed.
Min.  600mm.      mm away from its          ! The cable must be checked regularly and replaced
420mm.          420mm.  min. 650 mm. with hood min. 700 mm. without hood  sides.  by authorised technicians only.
• Any hoods must be
Min.            Min.   installed according to    ! The manufacturer declines any liability should
the instructions listed in  these safety measures not be observed.
the relevant operating    Gas connection
manual.                   Connection to the gas network or to the gas cylinder
may be carried out using a flexible rubber or steel
Levelling                                           hose, in accordance with current national legislation
If it is necessary to level the  and after making sure that the appliance is suited to
appliance, screw the            the type of gas with which it will be supplied (see the
adjustable feet into the places  rating sticker on the cover:  if this is not the case see
provided on each corner of the  below). When using liquid gas from a cylinder, install a
base of the cooker (see         pressure regulator which complies with current national
figure).                        regulations. To make connection easier, the gas
supply may be turned sideways*: reverse the position
of the hose holder with that of the cap and replace the
The legs* fit into the slots on  gasket that is supplied with the appliance.
the underside of the base of
the cooker.                     ! Check that the pressure of the gas supply is
consistent with the values indicated in the Table of
burner and nozzle specifications (see below). This
will ensure the safe operation and durability of your
appliance while maintaining efficient energy
consumption.
Electrical connection
Gas connection using a flexible rubber hose
Install a standardised plug corresponding to the
load indicated on the appliance data plate (see     Make sure that the hose complies with current
Technical data table).                              national legislation. The internal diameter of the hose
The appliance must be directly connected to the mains  must measure: 8 mm for liquid gas supply; 13 mm
using an omnipolar circuit-breaker with a minimum   for methane gas supply.
contact opening of 3 mm installed between the
appliance and the mains. The circuit-breaker must be  Once the connection has been performed, make
suitable for the charge indicated and must comply with  sure that the hose:
NFC 15-100 regulations (the earthing wire must not be  • Does not come into contact with any parts that
interrupted by the circuit-breaker). The supply cable  reach temperatures of over 50°C.
must be positioned so that it does not come into    • Is not subject to any pulling or twisting forces and
contact with temperatures higher than 50°C at any point.  that it is not kinked or bent.
• Does not come into contact with blades, sharp
Before connecting the appliance to the power           corners or moving parts and that it is not
supply, make sure that:                                compressed.
• The appliance is earthed and the plug is compliant  • Is easy to inspect along its whole length so that
with the law.                                        its condition may be checked.
• The socket can withstand the maximum power of     • Is shorter than 1500 mm.
the appliance, which is indicated by the data plate.  • Fits firmly into place at both ends, where it will be
• The voltage is in the range between the values       fixed using clamps that comply with current
indicated on the data plate.                         regulations.
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
* Only available in certain models
3