Плита INDESIT 7OIF 617K.A IX. Инструкция на русском языке

Operating Instructions
OVEN
Contents
GB
Installation, 2-3
GB           RS                                  Positioning
Electrical connections
English,1    Русский, 11                          Data plate
Description of the appliance, 4
Overall view
Control panel
Start-up and use, 5
Starting the oven
How to use the timer
Cooking modes, 6-7
Cooking modes
Practical cooking advice
Cooking advice table
7OIF 610 K.A RU
The electronic cooking programmer, 8
7OIF 617 K.A RU
7OIF 737 K.A RU                                   Precautions and tips, 9
General safety
7OIF 610 K.A IX RU                                Disposal
7OIF 617 K.A IX RU                                Respecting and conserving the environment
7OIF 737 K.A IX RU                                Maintenance and care, 10
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb
Assistance

Installation
! Before placing your new appliance into operation   Ventilation
GB      please read these operating instructions carefully.
They contain important information for safe use, for  To ensure good ventilation, the back panel of the
installation and for care of the appliance.          cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
! Please keep these operating instructions for future  completely flat surface with an opening of at least 45 x
reference. Pass them on to possible new owners of    560 mm (see diagrams).
the appliance.
Positioning
560 mm.  45 mm.
! Keep packaging material out of the reach of
children. It can become a choking or suffocation
hazard. see Precautions and tips).
! The appliance must be installed by a qualified
person in compliance with the instructions provided.
Incorrect installation may cause harm to persons,    Centring and fastening
animals or may damage property.
Secure the appliance to the cabinet by opening the
Fitting the appliance
oven door and putting 4 screws into the 4 holes of the
Use the appropriate cabinet to ensure that the       outer frame.
appliance functions properly.
•  The panels adjacent to the oven must be made of
heat-resistant material.
•  Cabinets with a veneer exterior must be assembled
with glues which can withstand temperatures of up
to 100°C.
•  To install the oven under the counter (see diagram)
and in a kitchen unit, the cabinet must have the
following dimensions:
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.
547 mm. min.
23 mm.   45 mm.   593 mm.
595 mm.         567 mm.  558 mm.
5 mm.
545 mm.
595 mm.
24 mm.
! The appliance must not come into contact with
electrical parts once it has been installed.
The consumption indications on the data plate have
been calculated for this type of installation.
2

Electrical connections                              • The socket can withstand the maximum power of
the appliance, which is indicated on the data    GB
! Ovens equipped with a three-pole power supply       plate (see below).
cable are designed to operate with alternating
current at the voltage and frequency indicated on   • The voltage must be in the range between the
the data plate located on the appliance (see below).  values indicated on the data plate (see below).
Fitting the power supply cable
• The socket is compatible with the plug of the
1. Open the terminal         appliance. If the socket is incompatible with the
board by inserting a         plug, ask an authorised technician to replace it. Do
screwdriver into the         not use extension cords or multiple sockets.
side tabs of the cover.
Use the screwdriver as     ! Once the appliance has been installed, the power
a lever by pushing it      supply cable and the electrical socket must be easily
down to open the cover     accessible.
(see diagram).             ! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
2. Loosen the cable        by authorised technicians only (see Assistance).
clamp screw and            ! The manufacturer declines any liability should
! The manufacturer declines any liability should
! The manufacturer declines any liability should
! The manufacturer declines any liability should
! The manufacturer declines any liability should
remove it, using a         these safety measures not be observed.
these safety measures not be observed.
these safety measures not be observed.
these safety measures not be observed.
these safety measures not be observed.
screwdriver as a lever
(see figure).
3. Remove the wire
contact screws L-N-
, then fasten the wires
under the screw heads,
respecting the colour
code: Blue (N), Brown       DATA PLATE
(L) and Yellow-Green                         width cm 43.5
Verde (  ).                 Dimensions       height cm 32
depth cm 40
Volume           lt. 56
Connecting the supply cable to the mains
Electrical       voltage: 220-240V ~ 50/60
Install a standardised plug corresponding to the     connections      maximum power absorbed 2800W
load indicated on the data plate (see side).
The appliance must be directly connected to the mains                 Directive 2002/40/EC on the label
using an omnipolar circuit-breaker with a minimum                     of electric ovens.
contact opening of 3 mm installed between the                         Norm EN 50304
appliance and the mains, suitable for the load indicated              Energy consumption for Natural
and complying with current electrical regulations (the  ENERGY LABEL   convection – heating mode:
Traditional mode
earthing wire must not be interrupted by the circuit-                 Declared energy consumption for
breaker). The supply cable must not come into contact                 Forced convection Class – heating
with surfaces with temperatures higher than 50°C.                     mode:         Baking
! The installer must ensure that the correct electrical               This appliance conforms to the
connection has been made and that it is compliant                     following European Economic
with safety regulations.                                              Community directives:
-2006/95/EEC of 12/12/06 (Low
Before connecting to the power supply, make sure that:                Voltage) and subsequent
amendments;
• The appliance is earthed and the plug is                            - 2004/108/EEC of 15/12/04
compliant with the law.                                             (Electromagnetic Compatibility) and
subsequent amendments;
- 93/68/EEC of 22/07/93 and
subsequent amendments.
- 2002/96/EC and subsequent
amendments.
3