Варочная газовая панель HOTPOINT-ARISTON PC 640 T (AN) R. Инструкция на русском языке

Operating Instructions
HOB
Contents                                            GB
Installation, 2-5
GB            RS                                    Positioning
Electrical connection
English, 1   ???????? ??                            Gas connection
Data plate
Burner and nozzle specifications
Description of the appliance, 6
Overall view
Start-up and use, 7
Practical advice on using the burners
Precautions and tips, 8
General safety
Disposal
7HPC 640 T GH /HA                                    Maintenance and care, 9
7HPC 640 T R/HA                                      Switching the appliance off
7HPC 640 T X /HA                                     Cleaning the appliance
7HPC 640 T R/HA                                      Gas tap maintenance
7HPC 640 /HA
7HPC 640 X /HA                                       Troubleshooting, 10
7HPC 631 X /HA
7HPC 640 GH /HA
7HPC 640 N /HA
7HPC 640 N GH /HA
7HPC 640 N X /HA
GPN 64 TA CI RFH
GPN 64 TO CI RFH
GPN 64 NI RFH
GPN 64 NCI RFH
GPN 64 NW RFH
GPN 64 CI RFH
1

Installation
GB      ! Before operating your new appliance please read      LPG cylinders, whether partially or completely full,
this instruction booklet carefully. It contains important   must not be installed or stored in rooms or storage
information for safe use, installation and care of the   areas that are below ground level (cellars, etc.). It
appliance.                                             is advisable to keep only the cylinder being used in
! Please keep these operating instructions for future   the room, positioned so that it is not subject to heat
reference. Pass them on to possible new owners of the   produced by external sources (ovens, fireplaces,
appliance.                                             stoves, etc. ) which could raise the temperature of
the cylinder above 50°C.
Positioning
! Keep packaging material out of the reach of children.   Fitting the appliance
It can become a choking or suffocation hazard (see   Gas and mixed hobs are manufactured with type X
Precautions and tips).                               degree protection against overheating. The following
! The appliance must be installed by a qualified     precautions must be taken when installing the hob:
professional according to the instructions provided.   •  Kitchen cabinets adjacent to the appliance and taller
Incorrect installation may cause harm to people and    than the top of the hob must be at least 600 mm
animals or may damage property.                        from the edge of the hob.
! This unit may be installed and used only in        •  Hoods must be installed according to their relative
permanently ventilated rooms in accordance with        installation instruction manuals and at a minimum
British Standard Codes Of Practice: B.S. 6172 / B.S.   distance of 650 mm from the hob.
5440, Par. 2 and B.S. 6891 Current Editions. The     •  Place the wall cabinets adjacent to the hood at
following requirements must be observed:               a minimum height of 420 mm from the hob (see
•  The room must be equipped with an air extraction    figure).
system that expels any combustion fumes. This may
consist of a hood or an electric fan that automatically               If the hob is installed beneath a
starts each time the appliance is switched on.                        wall cabinet, the latter must be
situated at a minimum of 700
600mm min.
650mm min.   420mm min.  mm above the hob (see figure).
In a chimney stack or branched flue.   Directly to   •  The installation cavity should have the dimensions
(exclusively for cooking appliances)  the Outside
indicated in the figure.
Fastening hooks are provided, allowing you to fasten
•  The room must also allow proper air circulation, as   the hob to tops that are between 20 and 40 mm
air is needed for combustion to occur normally. The   thick. To ensure the hob is securely fastened to the
flow of air must not be less than 2 m /h per kW of   top, we recommend you use all the hooks provided.
3
installed power.
The air circulation system may                            555 mm
take air directly from the outside
by means of a pipe with an                 55 mm
inner cross section of  at least
100 cm ; the opening must not                                       475 mm
2
A
be vulnerable to any type of
Examples of ventilation holes  blockages.
for comburant air.
The system can also provide      Hook fastening diagram
Adjacent  Room to be
Room    Vented     the air needed for combustion
indirectly, i.e. from adjacent
rooms fitted with air circulation
tubes as described above.
However, these rooms must not
be communal rooms, bedrooms
Enlarging the ventilation slot  or rooms that may present a fire
between window and floor.  hazard.                  Hooking position        Hooking position
for top H=20 mm         for top H=30 mm
•  Liquid petroleum gas sinks to the floor as it is                          Front
heavier than air. Therefore, rooms containing LPG
cylinders must also be equipped with vents to allow
gas to escape in the event of a leak. As a result
2

indicated on the data plate.                        GB
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum
contact opening of 3 mm installed between the
appliance and the mains.  The circuit-breaker must be
suitable for the charge indicated and must comply with
current electrical regulations (the earthing wire must
not be interrupted by the circuit-breaker). The supply
cable must not come into contact with surfaces with
temperatures higher than 50°C.
Hooking position          Back                       ! The installer must ensure that the correct electrical
for top H=40 mm                                      connection has been made and that it is compliant with
safety regulations.
! Use the hooks contained in the “accessory pack”    Before connecting to the power supply, make sure that:
•  Where the hob is not installed over a built-in oven, a   •  The appliance is earthed and the plug is compliant
wooden panel must be installed as insulation. This   with the law.
must be placed at a minimum distance of 20 mm     •  The socket can withstand the maximum power of the
from the lower part of the hob.                      appliance, which is indicated on the data plate.
Ventilation                                          •  The voltage is in the range between the values
To ensure adequate ventilation, the back panel of       indicated on the data plate.
the cabinet must be removed. It is advisable to install   •  The socket is compatible with the plug of the
the oven so that it rests on two strips of wood, or on a   appliance. If the socket is incompatible with the
completely flat surface with an opening of at least 45 x   plug, ask an authorised technician to replace it. Do
560 mm (see diagrams).                                  not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
When
installing     ! The cable must not be bent or compressed.
560 mm.  45 mm.  the          ! The cable must be checked regularly and replaced
by authorised technicians only (see Assistance).
cooktop
above          ! The manufacturer declines any liability should these
a built-       safety measures not be observed.
in oven
without        Gas connection
forced         The appliance should be connected to the main
ventilation,
ensure that there are air inlets and outlets for ventilating   gas supply or to a gas cylinder in compliance with
current national regulations. Before carrying out the
the interior of the cabinet adequately.
connection, make sure the cooker is compatible with
the gas supply you wish to use. If this is not the case,
follow the instructions indicated in the paragraph
“Adapting to different types of gas.”
When using liquid gas from a cylinder, install a
pressure regulator which complies with current national
regulations.
! Check that the pressure of the gas supply is
consistent with the values indicated in Table 1 (“Burner
and nozzle specifications”). This will ensure the safe
operation and longevity of your appliance while
maintaining efficient energy consumption.
Electrical connection                                Connection with a rigid pipe (copper or steel)
Hobs equipped with a three-pole power supply cable   ! Connection to the gas system must be carried out in
are designed to operate with alternating current at the   such a way as not to place any strain of any kind on
voltage and frequency indicated on the data plate (this   the appliance.
is located on the lower part of the appliance). The earth   There is an adjustable L-shaped pipe fitting on the
wire in the cable has a green and yellow cover. If the   appliance supply ramp and this is fitted with a seal
appliance is to be installed above a built-in electric   in order to prevent leaks. The seal must always be
oven, the electrical connection of the hob and the   replaced after rotating the pipe fitting (seal provided
oven must be carried out separately, both for electrical   with appliance). The gas supply pipe fitting is a
safety purposes and to make extracting the oven      threaded 1/2 gas cylindrical male attachment.
easier.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
3