Плита HOTPOINT-ARISTON C 3V M5 (W). Инструкция на русском языке

Operating Instructions
COOKER AND OVEN
Contents
GB
Installation, 2-3
GB           RS                                 Positioning and levelling
Electrical connections
English, 1   ?ONNEEE,12                          Technical data
Description of the appliance, 4
Overall view
Control panel
Start-up and use, 5-8
Starting the oven
Cooking modes
Electronic timer
Oven cooking advice table
Using the glass ceramic hob, 9
Switching the cooking zones on and off
Cooking zones
C3VM5R
Precautions and tips, 10
General safety
Disposal
Respecting and conserving the environment
Care and maintenance, 11
Switching the appliance off
Cleaning the oven
Replacing the oven light bulb
Cleaning the glass ceramic hob
Assistance

Installation
! Before operating your new appliance please read                       The legs* provided with the
GB
this instruction booklet carefully. It contains                         appliance fit into the slots on
important information concerning the safe installation                  the underside of the base of
and operation of the appliance.                                         the cooker.
! Please keep these operating instructions for future
reference. Make sure that the instructions are kept
with the appliance if it is sold, given away or moved.
Electrical connections
! The appliance must be installed by a qualified
professional according to the instructions provided.
Fitting the power supply cable
! Any necessary adjustment or maintenance must be
The cable should be suited to the type of electrical
performed after the appliance has been
connection used, according to the following
disconnected from the electricity supply.
connection diagram:
Positioning and levelling                                     400 3N          1    2  3   4   5
H05RR-F 5x2.5 CEI-UNEL 35363
R      S  T        N
! It is possible to install the appliance alongside
400V 2N         1   2   3   4   5
cupboards whose height does not exceed that of the
H05RR-F 4x2.5 CEI-UNEL 35363  R  S N
hob surface.
230V 1N         1   2   3   4   5
! Make sure that the wall in contact with the back of  H07RN-F 3x4 CEI-UNEL 35364               N
R
the appliance is made from a non-flammable, heat-
resistant material (T 90°C).
To install the power supply cable correctly:
To install the appliance correctly:
? Place it in the kitchen, the dining room or the bed-                        1. Loosen the screw V
sit (not in the bathroom).                                                  in the terminal board
? If the top of the hob is higher than the cupboards,                         and pull the cover to
the appliance must be installed at least 200 mm                             open it (see figure).
V
away from them.
? If the cooker is
HOOD            installed underneath a wall
cabinet, there must be a
Min.  600mm.      minimum distance of 420
420mm.           420mm.  min. 650 mm. with hood min. 700 mm. without hood  mm between this cabinet
Min.             Min.   and the top of the hob.                             2. Position the connection
This distance should be
increased to 700 mm if                              support A (see figure)
3
2
the wall cabinets are                               according to the
1
flammable (see figure).                             connection diagram shown
above. The terminal board
? Do not position blinds behind the cooker or less
is designed for single-
than 200 mm away from its sides.
phase 230 V connection:
B
? Any hoods must be installed according to the
terminals 1, 2 and 3 are
A
instructions listed in the relevant operating manual.
N               connected to each other;
Levelling
jumper 4-5 is located in the
If it is necessary to level the
lower area of the terminal board.
appliance, screw the
3. Position wires N and 6 according to the diagram
adjustable feet* into the
(see figure) and perform the connection by
places provided on each
tightening the terminal board screws as much as
corner of the base of the
possible.
cooker (see figure).
4. Position the remaining wires on terminals 1-2-3
and tighten the screws.
2

TECHNICAL DATA
5. Fix the power supply cable in place by fastening
GB
the cable clamp screw.
Oven dimensions
6. Close the terminal board cover by tightening the                   34x44x39 cm
(HxWxD)
screws V.
Volume
58 l
Useful
width 42 cm
measurements
Connecting the supply cable to the mains
depth 44 cm
relating to the oven
height 17 cm
compartment
Install a standardised plug corresponding to the
Power supply
voltage and      see data plate
load indicated on the data plate located on the
frequency
appliance.
Ceramic hob
The appliance must be directly connected to the
Front Left       1200 W
mains using an omnipolar circuit-breaker with a
Back Left        1800 W
minimum contact opening of 3 mm installed between    Back Right       1200 W
Front Right      1800 W
the appliance and the mains.  The circuit-breaker
Max. ceramic hob
must be suitable for the charge indicated and must
consumption      6000 W
comply with current electrical regulations (the
earthing wire must not be interrupted by the circuit-
Directive 2002/40/EC on the label of
electric ovens. Standard EN 50304
breaker). The supply cable must be positioned so
Energy consumption for Natural
that it does not come into contact with temperatures
convection ? heating mode: a Static;
higher than 50°C at any point.
ENERGY LABEL
Declared energy consumption for
Before connecting the appliance to the power
Forced convection Class ? heating
mode: b Fan-assisted.
supply, make sure that:
? The appliance is earthed and the plug is compliant
with the law.
? The socket can withstand the maximum power of
EC Directives: 73/23/EEC dated
19/02/73 (Low Voltage) and subsequent
the appliance, which is indicated by the data
amendments ?
plate.
89/336/EEC dated 03/05/89
? The voltage is in the range between the values
(Electromagnetic Compatibility) and
indicated on the data plate.
subsequent amendments ?
93/68/EEC dated 22/07/93 and
? The socket is compatible with the plug of the
subsequent amendments ?
appliance. If the socket is incompatible with the
2002/96/EC.
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be
easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only.
! The manufacturer declines any liability should
these safety measures not be observed.
Only available in certain models.
*
3