На сайте 124222 инструкции общим размером 502.89 Гб , которые состоят из 6279424 страниц
Руководство пользователя HOTPOINT-ARISTON 7OFTR 850 (AN) RU/HA. Основные функции, характеристики и условия эксплуатации изложены на 28 страницах документа в pdf формате.
Доступно к просмотру 26 страниц. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.
Operating Instructions OVEN Contents GB Installation, 2-3 GB RS Positioning Electrical connections English,1 ???????, 13 Description of the appliance, 4 Overall view Control panel Start-up and use, 5 Starting the oven Using the cooking timer Data plate The electronic cooking programmer, 6 7OFH 837 C RU /HA Analogue Programmer, 7 7OFTR 850 RU /HA 7OF 937 C.1 RU/HA Cooking modes, 8-10 7OF 937 C.1 IX RU/HA Cooking modes 7OFH 837 C IX RU/HA Practical cooking advice 7OFQ 837 C.1 /HA Cooking advice table Precautions and tips, 11 General safety Disposal Respecting and conserving the environment Assistance Maintenance and care, 12 Switching the appliance off Cleaning the appliance Cleaning the oven door Replacing the light bulb Sliding Rack Kit assembly
Installation ! Before placing your new appliance into operation Ventilation GB please read these operating instructions carefully. They contain important information for safe use, for To ensure good ventilation, the back panel of the installation and for care of the appliance. cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a ! Please keep these operating instructions for future completely flat surface with an opening of at least 45 x reference. Pass them on to possible new owners of 560 mm (see diagrams). the appliance. Positioning 560 mm. 45 mm. ! Keep packaging material out of the reach of children. It can become a choking or suffocation hazard. see Precautions and tips). ! The appliance must be installed by a qualified person in compliance with the instructions provided. Incorrect installation may cause harm to persons, Centring and fastening animals or may damage property. Position the 4 tabs on the side of the oven according Fitting the appliance to the 4 holes of the outer frame. Adjust the tabs Use the appropriate cabinet to ensure that the according to the thickness of the cabinet side panel, appliance functions properly. as shown below: thickness of 20 mm: take off • The panels adjacent to the oven must be made of the removable part of the tab heat-resistant material. (see diagram) • Cabinets with a veneer exterior must be assembled with glues which can withstand temperatures of up to 100°C. • To install the oven under the counter (see diagram) thickness of 18 mm: use the and in a kitchen unit, the cabinet must have the first groove, which has already following dimensions: been set in the factory (see diagram) 547 mm. min. 23 mm. 45 mm. 593 mm. thickness of 16 mm: use the 595 mm. 567 mm. 558 mm. second groove (see diagram) 5 mm. 545 mm. 595 mm. 24 mm. Secure the appliance to the cabinet by opening the ! The appliance must not come into contact with oven door and putting 4 screws into the 4 holes of the outer frame. electrical parts once it has been installed. The consumption indications on the data plate have ! All parts which ensure the safe operation of the been calculated for this type of installation. appliance must not be removable without the aid of a tool. 2
Centring and fixing* Connecting the supply cable to the mains GB “A” “A” “A” 1. Position brackets “A”“A” against oven support “BB BB B”. Install a standardised plug corresponding to the “C” “C” “C” “A” “A” “A” 2. Position tabs “C”“C” against brackets “A” “A”. If the load indicated on the data plate (see side). thickness of the cabinet side panel: The appliance must be directly connected to the mains • is 16 mm thick: place the tab so that the using an omnipolar circuit-breaker with a minimum number 16 written on it is facing you; contact opening of 3 mm installed between the appliance • is 18 mm thick: place the tab so that the part and the mains, suitable for the load indicated and without any text is facing you; complying with current electrical regulations (the earthing • is 20 mm thick: do not fit the tab. wire must not be interrupted by the circuit-breaker). The 3. Fix the brackets and tabs onto the edge of the supply cable must not come into contact with surfaces “D”. “D”. “D”. cabinet side panel using screws “D”.“D”. with temperatures higher than 50°C. 4. Fix the oven to the cabinet using the screws and ! The installer must ensure that the correct electrical “E”. “E” plastic washers “E” “E” “E” connection has been made and that it is compliant with safety regulations. 16 D C 16 Before connecting to the power supply, make sure that: D C A E • The appliance is earthed and the plug is compliant with the law. 16 16 C E • The socket can withstand the maximum power of D the appliance, which is indicated on the data plate (see below). B • The voltage must be in the range between the Electrical connections values indicated on the data plate (see below). ! Ovens equipped with a three-pole power supply • The socket is compatible with the plug of the cable are designed to operate with alternating appliance. If the socket is incompatible with the current at the voltage and frequency indicated on plug, ask an authorised technician to replace it. Do the data plate located on the appliance (see below). not use extension cords or multiple sockets. Fitting the power supply cable ! Once the appliance has been installed, the power 1. Open the terminal supply cable and the electrical socket must be easily board by inserting a accessible. screwdriver into the side tabs of the cover. ! The cable must not be bent or compressed. Use the screwdriver as a lever by pushing it ! The cable must be checked regularly and replaced down to open the cover by authorised technicians only (see Assistance). (see diagram). ! The manufacturer declines any liability should ! The manufacturer declines any liability should ! The manufacturer declines any liability should ! The manufacturer declines any liability should ! The manufacturer declines any liability should 2. Loosen the cable these safety measures not be observed. these safety measures not be observed. these safety measures not be observed. these safety measures not be observed. these safety measures not be observed. clamp screw and remove it, using a screwdriver as a lever (see figure). 3. Remove the wire contact screws L-N- , then fasten the wires under the screw heads, respecting the colour code: Blue (N), Brown (L) and Yellow-Green Verde ( ). * Only on certain models. 3