Встраиваемый электрический духовой шкаф HOTPOINT-ARISTON 7OFHR 640 (AN) RU/HA. Инструкция на русском языке

Operating Instructions
OVEN
Contents
GB
Installation, 2-3
GB           RS                                   Positioning
Electrical connections
Data plate
English,1    Русский, 11
Description of the appliance, 4
Overall view
Control panel
Start-up and use, 5
Starting the oven
How to use the timer
Using the cooking timer
Clock with Country Style timer
The electronic cooking programmer, 6
Setting the clock
Setting the timer
Programming cooking
7OF 627 C RU /HA
7OF 637 C RU /HA                                   Cooking modes, 7-8
7OF 627 C IX RU /HA                                Cooking modes
7OF 637 C IX RU /HA                                Practical cooking advice
7OFD 610 RU/HA                                     Cooking advice table
7OFH 620 RU /HA
7OF 627 C.1 RU/HA                                  Precautions and tips, 9
7OFH 62 RU/HA                                      General safety
Disposal
7OFH 62 IX RU/HA                                   Respecting and conserving the environment
7OFHR 640 RU/HA                                    Assistance
Maintenance and care, 10
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb

Installation
! Before placing your new appliance into operation   Ventilation
GB      please read these operating instructions carefully.
They contain important information for safe use, for  To ensure good ventilation, the back panel of the
installation and for care of the appliance.          cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
! Please keep these operating instructions for future  completely flat surface with an opening of at least 45 x
reference. Pass them on to possible new owners of the  560 mm (see diagrams).
appliance.
Positioning
! Keep packaging material out of the reach of children.                    560 mm.  45 mm.
It can become a choking or suffocation hazard. see
Precautions and tips).
! The appliance must be installed by a qualified person
in compliance with the instructions provided. Incorrect
installation may cause harm to persons, animals or
may damage property.                                 Centring and fastening
Fitting the appliance                                Position the 4 tabs on the side of the oven according
to the 4 holes of the outer frame. Adjust the tabs
Use the appropriate cabinet to ensure that the       according to the thickness of the cabinet side panel,
appliance functions properly.                        as shown below:
thickness of 20 mm: take off
•  The panels adjacent to the oven must be made of                      the removable part of the tab
heat-resistant material.
(see diagram)
•  Cabinets with a veneer exterior must be assembled
with glues which can withstand temperatures of up
to 100°C.
•  To install the oven under the counter (see diagram)
and in a kitchen unit, the cabinet must have the
following dimensions:                                                 thickness of 18 mm: use the
first groove, which has already
been set in the factory (see
diagram)
547 mm. min.
23 mm.   45 mm.   593 mm.
595 mm.         567 mm.  558 mm.                                       thickness of 16 mm: use the
second groove (see diagram)
5 mm.
545 mm.
595 mm.
24 mm.
! The appliance must not come into contact with      Secure the appliance to the cabinet by opening the
electrical parts once it has been installed.         oven door and putting 4 screws into the 4 holes of the
The consumption indications on the data plate have   outer frame.
been calculated for this type of installation.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.
2

Electrical connections                              • The socket is compatible with the plug of the
appliance. If the socket is incompatible with the  GB
! Ovens equipped with a three-pole power supply       plug, ask an authorised technician to replace it. Do
cable are designed to operate with alternating current  not use extension cords or multiple sockets.
at the voltage and frequency indicated on the data
plate located on the appliance (see below).         ! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
Fitting the power supply cable                      accessible.
! The cable must not be bent or compressed.
1. Open the terminal       ! The cable must be checked regularly and replaced
board by inserting a       by authorised technicians only (see Assistance).
screwdriver into the side
! The manufacturer declines any liability should
! The manufacturer declines any liability should
! The manufacturer declines any liability should
! The manufacturer declines any liability should
tabs of the cover. Use     ! The manufacturer declines any liability should
these safety measures not be observed.
these safety measures not be observed.
these safety measures not be observed.
these safety measures not be observed.
the screwdriver as a       these safety measures not be observed.
lever by pushing it down
to open the cover (see
diagram).
2. Loosen the cable
clamp screw and remove
it, using a screwdriver as
a lever (see figure).
DATA PLATE
3. Remove the wire                            width cm 43.5
contact screws L-N-    ,    Dimensions        height cm 32
then fasten the wires                         depth cm 41.5
under the screw heads,
respecting the colour       Volume            lt. 58
code: Blue (N), Brown (L)
and Yellow-Green Verde      Dimensions of     width cm 37.5
height cm 32
models with
(  ).
removable racks   depth cm 41.5
Volume of models
with removable    lt. 50
racks
Connecting the supply cable to the mains
voltage: 220-230V~ or 220-240V~
Install a standardised plug corresponding to the load  Electrical      50/60 Hz or 50Hz  (see data plate)
indicated on the data plate (see side).              connections       maximum power absorbed 2800W
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum contact              Directive 2002/40/EC on the label
opening of 3 mm installed between the appliance and the
mains, suitable for the load indicated and complying with              of electric ovens.
Norm EN 50304
current electrical regulations (the earthing wire must not be          Energy consumption for Natural
interrupted by the circuit-breaker). The supply cable must  ENERGY LABEL   convection – heating mode:
not come into contact with surfaces with temperatures                  Traditional mode
higher than 50°C.                                                      Declared energy consumption for
Forced convection Class – heating
! The installer must ensure that the correct electrical                mode:         Baking
connection has been made and that it is compliant with
safety regulations.
This appliance conforms to the
Before connecting to the power supply, make sure that:                 following European Economic
Community directives:
• The appliance is earthed and the plug is compliant                   -2006/95/EEC of 12/12/06 (Low
with the law.                                                        Voltage) and subsequent
• The socket can withstand the maximum power of the                    amendments;
appliance, which is indicated on the data plate (see                 - 2004/108/EEC of 15/12/04
below).                                                              (Electromagnetic Compatibility) and
• The voltage must be in the range between the                         subsequent amendments;
values indicated on the data plate (see below).                      - 93/68/EEC of 22/07/93 and
subsequent amendments.
- 2002/96/EC and subsequent
amendments.
3