Духовой шкаф HOTPOINT-ARISTON 7OFH 51 (WH) RU HA. Инструкция на русском языке

Operating Instructions
OVEN
Contents
GB
Installation, 2-3
GB           RS             KZ                     Positioning
Electrical connections
English,1    ????????? ??                           Data plate
Description of the appliance, 4
Overall view
Control panel
Start-up and use, 5
Starting the oven
How to use the timer
Cooking modes, 6-7
Cooking modes
Practical cooking advice
Cooking advice table
7OFH 51 RU/HA
Precautions and tips, 8
7OFH 51 IX RU/HA                                    General safety
Disposal
Respecting and conserving the environment
Assistance
Maintenance and care, 9
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb

Installation
! Before placing your new appliance into operation   Ventilation
GB      please read these operating instructions carefully.
They contain important information for safe use, for  To ensure good ventilation, the back panel of the
installation and for care of the appliance.          cabinet must be removed. It is advisable to install
the oven so that it rests on two strips of wood, or on
! Please keep these operating instructions for future  a completely flat surface with an opening of at least
reference. Pass them on to possible new owners of    45 x 560 mm (see diagrams).
the appliance.
Positioning                                                                       45 mm.
560 mm.
! Keep packaging material out of the reach of
children. It can become a choking or suffocation
hazard. (see Precautions and tips).
! The appliance must be installed by a qualified
person in compliance with the instructions provided.
Incorrect installation may cause harm to persons,    Centring and fastening
animals or may damage property.
Position the 4 tabs on the side of the oven according
Fitting the appliance                                to the 4 holes of the outer frame. Adjust the tabs
according to the thickness of the cabinet side panel,
Use the appropriate cabinet to ensure that the       as shown below:
appliance functions properly.
thickness of 20 mm: take off
• The panels adjacent to the oven must be made of                       the removable part of the tab
heat-resistant material.
(see diagram)
• Cabinets with a veneer exterior must be assembled
with glues which can withstand temperatures of up
to 100°C.
•  to install the oven under the counter (see diagram)
and in a kitchen unit, the cabinet must have the                      thickness of 18 mm: use the
following dimensions:                                                 first groove, which has already
been set in the factory (see
diagram)
547 mm. min.
23 mm.    45 mm.   593 mm.
595 mm.         567 mm.  558 mm.                                      thickness of 16 mm: use the
second groove (see diagram)
5 mm.
545 mm.
595 mm.
24 mm.                                                         Secure the appliance to the
! The appliance must not come into contact with                         cabinet by opening the oven
electrical parts once it has been installed.                            door and putting 4 screws into
The consumption indications on the data plate have                      the 4 holes of the outer frame.
been calculated for this type of installation.
! All parts which ensure the
safe operation of the
appliance must not be
2

removable without the aid of a tool.                • The socket can withstand the maximum power of
the appliance, which is indicated on the data    GB
Electrical connections                                 plate (see below).
• The voltage must be in the range between the
! Ovens equipped with a three-pole power supply        values indicated on the data plate (see below).
cable are designed to operate with alternating      • The socket is compatible with the plug of the
current at the voltage and frequency indicated on      appliance. If the socket is incompatible with the
the data plate located on the appliance (see below).   plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
Fitting the power          ! Once the appliance has been installed, the power
supply cable
supply cable and the electrical socket must be easily
1. Open the terminal       accessible.
board by inserting a       ! The cable must not be bent or compressed.
screwdriver into the       ! The cable must be checked regularly and replaced
side tabs of the cover.    by authorised technicians only (see Assistance).
Use the screwdriver as     ! The manufacturer declines any liability should
a lever by pushing it      these safety measures not be observed.
down to open the cover
(see diagram).
2. Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever
(see figure).
3. Remove the wire
contact screws L-N-         DATA PLATE
, then fasten the wires                      width cm 43.5
under the screw heads,      Dimensions       height cm 32
respecting the colour                        depth cm 41,5
code: Blue (N), Brown
(L) and Yellow-Green Verde (  ).                     Volume           lt. 58
voltage: 220-240V ~ 50/60Hz o 50Hz
Electrical
Connecting the supply cable to the mains             connections      (see data plate) maximum power
absorbed 2250W
Install a standardised plug corresponding to the                      Directive 2002/40/EC on the label of
load indicated on the data plate (see side).                          electric ovens Norm EN 50304
The appliance must be directly connected to the
mains using an omnipolar circuit-breaker with a                       Energy consumption for Natural
minimum contact opening of 3 mm installed between    ENERGY LABEL     convection heating mode:
the appliance and the mains, suitable for the load                    ? Convection
Declared energy consumption for
indicated and complying with current electrical                       Forced convection Class
regulations (the earthing wire must not be interrupted                heating mode: ? Fan assisted
by the circuit-breaker). The supply cable must not                    This appliance conforms to the
come into contact with surfaces with temperatures                     following European Economic
higher than 50°C.                                                     Community directives:
- 2006/95/EEC of 12/12/06 (Low
! The installer must ensure that the correct electrical               Voltage) and subsequent
connection has been made and that it is compliant                     amendments;
with safety regulations.                                              - 2004/108/EEC of 15/12/04
(Electromagnetic Compatibility) and
Before connecting to the power supply, make sure                      subsequent amendments;
that:                                                                 - 93/68/EEC of 22/07/93 and
• The appliance is earthed and the plug is                            subsequent amendments.
- 2002/96/EC and subsequent
compliant with the law.
amendments.
3