Духовой шкаф HOTPOINT-ARISTON 7OFH 1037 C IXRU HA. Инструкция на русском языке

Operating Instructions
OVEN
Contents
GB
Installation,  2-3
GB           RS                                     Positioning
Electrical connection
English,1    Русский,  14                            Data plate
Description of the appliance,  4
Overall view
Control panel
Start-up and use,  5
Control panel lock
DEMO mode
Setting the clock and timer
Starting the oven
Cooking modes,  6-9
Manual cooking modes
7OF 1039 C.1 IX RU/HA                                Automatic cooking modes
7OFH 1037 C IX RU/HA                                 Programming the cooking mode
Practical cooking advice
Cooking advice table
Precautions and tips,  10
General safety
Disposal
Respecting and conserving the environment
Care and maintenance,  11-12
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb
Assembling the sliding rack kit
Assistance,  13

Installation
! Before operating your new appliance please read    Ventilation
GB      this instruction booklet carefully. It contains
important information concerning the safe operation,  To ensure adequate ventilation is provided, the back
installation and maintenance of the appliance.       panel of the cabinet must be removed. It is
advisable to install the oven so that it rests on two
! Please keep these operating instructions for future  strips of wood, or on a completely flat surface with
reference. Pass them on to possible new owners of    an opening of at least 45 x 560 mm (see diagrams).
the appliance.
Positioning
! Keep all packaging materials out of the reach of                         560 mm.  45 mm.
children. It may present a choking or suffocation
hazard (see Precautions and tips).
! The appliance must be installed by a qualified
professional in accordance with the instructions
provided. Incorrect installation may cause harm to
people and animals or may damage property.           Centring and fixing
Position the 4 tabs on the side of the oven so that
Built-in appliance                                   they are lined up with the 4 holes on the outer frame.
Use the appropriate cabinet to ensure that the       Adjust the tabs according to the thickness of the
appliance functions properly.                        cabinet side panel, as shown below:
20 mm thick: take off the
• The panels adjacent to the oven must be made of                       removable part of the tab (see
heat-resistant material.                                              diagram).
• Cabinets with a veneer exterior must be
assembled with glues which can withstand
temperatures of up to 100°C.
• To install the oven under the counter (see                            18 mm thick: use the first
diagram) and in a kitchen unit, the cabinet must                      groove, which has already
have the following dimensions:                                        been set in the factory (see
diagram).
547 mm. min.
23 mm.    45 mm.   593 mm.                                 16 mm thick: use the second
595 mm.         567 mm.  558 mm.                                       groove (see diagram).
5 mm.
545 mm.
595 mm.
Secure the appliance to the cabinet by opening the
24 mm.                                       oven door and putting 4 screws into the 4 holes on
the outer frame.
! The appliance must not come into contact with
electrical parts once it has been installed.         ! All parts which ensure the safe operation of the
The indications for consumption given on the data    appliance must not be removable without the aid of
plate have been calculated for this type of installation.  a tool.
2

Electrical connection                               • The socket can withstand the maximum power of
the appliance, which is indicated on the data     GB
! Ovens equipped with a three-pole power supply
cable are designed to operate with alternating        plate (see below).
current at the voltage and frequency indicated on   • The voltage is in the range between the values
the data plate located on the appliance (see below).  indicated on the data plate (see below).
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
Fitting the power supply cable
plug, ask an authorised technician to replace it.
1. Open the terminal         Do not use extension cords or multiple sockets.
board by inserting a       ! Once the appliance has been installed, the power
screwdriver into the       supply cable and the electrical socket must be
side tabs of the cover.    easily accessible.
Use the screwdriver as     ! The cable must not be bent or compressed.
a lever by pushing it      ! The cable must be checked regularly and replaced
down to open the cover     by authorised technicians only (see Assistance).
(see diagram).             ! The manufacturer declines any liability should
these safety measures not be observed.
2. Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever      TABLE OF CHARACTERISTICS
(see figure).                                  width 43.5 cm
Dimensions         height 32 cm
3. Remove the wire                             depth 40 cm
contact screws L-N-         Volume             56 l
, then fasten the wires                        width 43.5 cm
under the screw heads,      Dimensions *       height 32 cm
respecting the colour                          depth 41.5 cm
code: Blue (N), Brown       Volume *           58 l
(L) and Yellow-Green        Electrical         voltage: 220-240V ~ 50Hz
Verde (  ).                 connections        maximum power absorbed
2800 W
Directive 2002/40/EC on the
label of electric ovens.
Connecting the supply cable to the mains                                Regulation EN 50304
Install a standardised plug corresponding to the     ENERGY LABEL **
load indicated on the data plate (see table).                           Declared energy
The appliance must be directly connected to the                         consumption for Forced
mains using an omnipolar circuit-breaker with a                         convection Class
minimum contact opening of 3 mm installed between                       – heating mode:          Gratin
This appliance conforms to
the appliance and the mains.  The circuit-breaker                       the following European
must be suitable for the charge indicated and must                      Economic Community
comply with current electrical regulations (the                         directives: 2006/95/EEC
earthing wire must not be interrupted by the circuit-                   dated 12/12/06 (Low
breaker). The supply cable must be positioned so                        Voltage) and subsequent
that it does not come into contact with temperatures                    amendments –
higher than 50°C at any point.                                          2004/108/EEC dated
15/12/04 (Electromagnetic
Compatibility) and
! The installer must ensure that the correct electrical                 subsequent amendments -
connection has been made and that it is fully                           93/68/EEC dated 22/07/93
compliant with safety regulations.                                      and subsequent
amendments.
Before connecting the appliance to the power                            2002/96/EEC and
supply, make sure that:                                                 subsequent amendments.
1275/2008 standby/off mode
• The appliance is earthed and the plug is           * With glass panel fitted to the inside of the door
compliant with the law.                            ** Without removable guide rails
3