Варочная поверхность HOTPOINT-ARISTON 7HTD 640 (ICE) IX/HA. Инструкция на русском языке

Instructions for use
WASHING MACHINE
Contents                                             GB
Installation, 2-3
GB            CIS                                   Unpacking and levelling
Connecting the electricity and water supplies
English, 1    ???????, 13                            The first wash cycle
Technical data
Description of the washing machine, 4-5
Control panel
Display
How to open and shut the drum
Running a wash cycle, 6
Load balancing system
Wash cycles and functions, 7
Table of wash cycles
Wash functions
ARTXD 109
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Precautions and tips, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning your appliance
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
How to clean the detergent dispenser
Troubleshooting, 11
Service, 12
1

Installation
! Keep this instruction manual in a safe place for future refe-  Electric and water connections
GB
rence. Should the appliance be sold, transferred or moved,
make sure the instruction manual accompanies the washing   Connecting the water inlet hose
machine to inform the new owner as to its operation and
features.                                                                     1. Connect the supply pipe
by screwing it to a cold water
! Read these instructions carefully: they contain vital infor-                tab using a ? gas threaded
mation on installation, use and safety.                                       connection (see figure).
Before performing the con-
Unpacking and levelling                                                       nection, allow the water to
run freely until it is perfectly
Unpacking                                                                     clear.
1.  Unpack  the  washing
machine.
2. Check whether the wa-
shing  machine  has  been                           2. Connect the other end of
damaged during transport.                           the water inlet hose to the
If this is the case, do not                         washing machine, screwing
install it and contact your                         it onto the appliance’s cold
retailer.                                           water inlet, situated on the
3. Remove the four protec-                          top  right-hand  side  on  the
tive screws and the rubber                          rear  of  the  appliance  (see
washer with the respective                          figure).
spacer,  situated  on  the
rear of the appliance (see
figure).
4. Seal the gaps using the   3. Make sure there are no kinks or bends in the hose.
plastic plugs provided.
5. Keep all the parts: you will need them again if the washing   !  The  water  pressure  at  the  tap  must  be  within
machine needs to be moved to another location.         the  values  indicated  in  the  Technical  details  table
(on the next page).
Warning: should the screws be re-used, make sure you fasten   !  If the water inlet hose is not long enough, contact a spe-
the shorter ones at the top.                           cialist store or an authorised serviceman.
! Packaging materials are not children’s toys.
Levelling
Your machine may make a considerable amount of noise if
the two front feet have not been adjusted correctly.
1.  Install  the  washing  ma-
chine on a flat sturdy floor,
without resting it up against
walls,  furniture  cabinets  or
other.
2. If the floor is not perfectly
level,  compensate  for  any
unevenness by tightening or
loosening the adjustable front
feet (see figure); the angle of
inclination, measured accor-
ding to the worktop, must not exceed 2°.
Levelling your appliance correctly will provide it with stability
and avoid any vibrations, noise and shifting during operation.
If it is placed on a fitted or loose carpet, adjust the feet in
such a way as to allow enough room for ventilation beneath
the washing machine.
2

Connecting the drain hose                            ! Do not use extension cords or multiple sockets.
GB
Connect the drain hose,     ! The cable should not be bent or compressed.
without bending it, to a drai-
nage duct or a wall drain   ! The power supply cable must only be replaced by autho-
located at a height between   rised technicians.
65 and 100 cm from the
65 - 100 cm           floor;                      Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
alternatively, rest it on   Once the appliance has been installed, and before you use
the side of a washbasin     it for the first time, run a wash cycle with detergent and no
or bathtub, fastening the   laundry, using the wash cycle   .
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
Technical details
! We advise against the use of hose extensions; if it is   Model      ARTXD 109
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm              40 cm wide
in length.                                            Dimensions      85 cm high
60 cm deep
Capacity        from 1 to 6 kg
Electrical connections
Electric        Please refer to the technical data plate
Before plugging the appliance into the electricity socket,   connections  fixed to the machine.
make sure that:
Water           maximum pressure 1 MPa (10 bar)
• the socket is earthed and complies with all applicable   connections  minimum pressure 0.05 MPa (0.5 bar)
laws;                                                                drum capacity 42 litres
Spin speed      up to 1000 rpm
• the socket is able to withstand the maximum power load
of the appliance as indicated in the Technical data table   Test wash
(see opposite);                                      cycles in
accordance      programme   ; temperature 60°C
• the power supply voltage falls within the values indicated   with directives  programme   ; temperature 40°C.
in the Technical data table (see opposite);          1061/2010 and
1015/2010
• the socket is compatible with the plug of the washing
machine. If this is not the case, replace the socket or the          This appliance is compliant with
plug.                                                                the following European Community
Directives:
! The washing machine must not be installed outdoors,                 - 2004/108/CE (Electromagnetic
even in covered areas. It is extremely dangerous to leave             Compatibility)
- 2006/95/CE (Low Voltage)
the appliance exposed to rain, storms and other weather               - 2002/96/CE
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
3