Встраиваемая газовая варочная панель HOTPOINT-ARISTON 7HPC 640 T X /HA. Инструкция на русском языке

Operating Instructions
HOB
Contents
GB                                                                                                            GB
Installation, 2-5
GB            RS                                    Positioning
Electrical connection
English,1    ???????,12                             Gas connection
Data plate
Burner and nozzle specifications
Description of the appliance, 6
Overall view
Start-up and use, 7-8
Practical advice on using the burners
Practical advice on using the electric hotplates
Precautions and tips, 9
General safety
Disposal
CISPH640 M  /HA
CISPH640 M IX /HA                                   Maintenance and care, 10
CISPH640 MS /HA                                     Switching the appliance off
CISPH640 MS IX /HA                                  Cleaning the appliance
CISPH640 MST /HA                                    Gas tap maintenance
CISPH640 MST IX /HA
7HPH 640 RU/HA                                      Troubleshooting, 11
7HPH 640 GH RU/HA
7HPH 640S RU/HA
7HPH 640 ST /HA
7HPH 640 ST GH RU/HA
7HPHR 640 ST /HA
7HPH 631 MS IX RU/HA
7HPH 631 MS RU/HA

Installation
! Before operating your new appliance please read this  also be equipped with vents to allow gas to escape in the
GB      instruction booklet carefully. It contains important information  event of a leak. As a result LPG cylinders, whether
for safe use, installation and care of the appliance.  partially or completely full, must not be installed or stored
! Please keep these operating instructions for future  in rooms or storage areas that are below ground level
reference. Pass them on to possible new owners of the  (cellars, etc.). It is advisable to keep only the cylinder
appliance.                                             being used in the room, positioned so that it is not
subject to heat produced by external sources (ovens,
Positioning                                            fireplaces, stoves, etc. ) which could raise the
! Keep packaging material out of the reach of children. It  temperature of the cylinder above 50°C.
can become a choking or suffocation hazard (see
Precautions and tips).                               Fitting the appliance
! The appliance must be installed by a qualified professional  Gas and mixed hobs are manufactured with type X degree
protection against overheating. The following precautions
according to the instructions provided. Incorrect installation  must be taken when installing the hob:
may cause harm to people and animals or may damage
property.                                            • Kitchen cabinets adjacent to the appliance and taller
! This unit may be installed and used only in permanently  than the top of the hob must be at least 600 mm from the
edge of the hob.
ventilated rooms in accordance with British Standard Codes
Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891  • Hoods must be installed according to their relative
Current Editions. The following requirements must be   installation instruction manuals and at a minimum
observed:                                              distance of 650 mm from the hob.
• The room must be equipped with an air extraction system  • Place the wall cabinets adjacent to the hood at a
that expels any combustion fumes. This may consist of a  minimum height of 420 mm from the hob (see figure).
hood or an electric fan that automatically starts each time
the appliance is switched on.                                         If the hob is installed beneath a
wall cabinet, the latter must be
situated at a minimum of 700 mm
700mm min.   600mm min.  above the hob (see figure).
600mm min.
In a chimney stack or branched flue.   Directly to
(exclusively for cooking appliances)  the Outside  • The installation cavity should have the dimensions
indicated in the figure.
• The room must also allow proper air circulation, as air is
needed for combustion to occur normally. The flow of air  Fastening hooks are provided, allowing you to fasten the
must not be less than 2 m /h per kW of installed power.  hob to tops that are between 20 and 40 mm thick. To
3
The air circulation system may     ensure the hob is securely fastened to the top, we
take air directly from the outside  recommend you use all the hooks provided.
by means of a pipe with an inner                          555 mm
cross section of  at least 100 cm ;
2
A           the opening must not be                    55 mm
vulnerable to any type of                                           475 mm
Examples of ventilation holes
blockages.
for comburant air.
The system can also provide the
Adjacent  Room to be
Room   Vented
air needed for combustion        Hook fastening diagram
indirectly, i.e. from adjacent rooms
fitted with air circulation tubes as
described above. However, these
rooms must not be communal
Enlarging the ventilation slot  rooms, bedrooms or rooms that
between window and floor.                          Hooking position        Hooking position
may present a fire hazard.
for top H=20 mm         for top H=30 mm
• Liquid petroleum gas sinks to the floor as it is heavier
than air. Therefore, rooms containing LPG cylinders must
2

Front                       Connecting the supply cable to the mains
Install a standardised plug corresponding to the load  GB
indicated on the data plate.
The appliance must be directly connected to the mains using
an omnipolar circuit-breaker with a minimum contact opening
of 3 mm installed between the appliance and the mains.  The
circuit-breaker must be suitable for the charge indicated and
must comply with current electrical regulations (the earthing
wire must not be interrupted by the circuit-breaker). The
Hooking position         Back                       supply cable must not come into contact with surfaces with
for top H=40 mm                                     temperatures higher than 50°C.
! Use the hooks contained in the “accessory pack”   ! The installer must ensure that the correct electrical
• Where the hob is not installed over a built-in oven, a  connection has been made and that it is compliant with
wooden panel must be installed as insulation. This must  safety regulations.
be placed at a minimum distance of 20 mm from the  Before connecting to the power supply, make sure that:
lower part of the hob.                            • The appliance is earthed and the plug is compliant with
Ventilation                                            the law.
To ensure adequate ventilation, the back panel of the  • The socket can withstand the maximum power of the
cabinet must be removed. It is advisable to install the oven  appliance, which is indicated on the data plate.
so that it rests on two strips of wood, or on a completely flat  • The voltage is in the range between the values indicated
surface with an opening of at least 45 x 560 mm (see   on the data plate.
diagrams).                                          • The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
560 mm.  45 mm.               ! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
When installing the cooktop above a built-in oven   ! The manufacturer declines any liability should these safety
without forced ventilation, ensure that there are air  measures not be observed.
inlets and outlets for ventilating the interior of the
cabinet adequately.                                 Gas connection
The appliance should be connected to the main gas supply
or to a gas cylinder in compliance with current national
regulations. Before carrying out the connection, make sure
the cooker is compatible with the gas supply you wish to
use. If this is not the case, follow the instructions indicated in
the paragraph “Adapting to different types of gas.”
When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.
Electrical connection                               ! Check that the pressure of the gas supply is consistent
with the values indicated in Table 1 (“Burner and nozzle
Hobs equipped with a three-pole power supply cable are  specifications”). This will ensure the safe operation and
designed to operate with alternating current at the voltage  longevity of your appliance while maintaining efficient
and frequency indicated on the data plate (this is located on  energy consumption.
the lower part of the appliance). The earth wire in the cable
has a green and yellow cover. If the appliance is to be  Connection with a rigid pipe (copper or steel)
installed above a built-in electric oven, the electrical  ! Connection to the gas system must be carried out in such
connection of the hob and the oven must be carried out  a way as not to place any strain of any kind on the
separately, both for electrical safety purposes and to make  appliance.
extracting the oven easier.                         There is an adjustable LL LL L-shaped pipe fitting on the
3