На сайте 124163 инструкции общим размером 502.65 Гб , которые состоят из 6277023 страниц
Руководство пользователя DIMPLEX TS521W. Основные функции, характеристики и условия эксплуатации изложены на 1 странице документа в pdf формате.
Доступно к просмотру 1 страница. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.
Bimetal 5 o - 35 o C outlet box 41 o - 95 o F WARNING WARNING Mounting: COVER Approvals: FEATURES required by law. 0 - 4986 watts at Electrical Ratings SPECIFICATIONS Sensing Element: product damage. Electrical Ratings: 277 volts (18 amps) 120 volts (22 amps) 0 - 2640 watts max. at 0 - 4576/5280 watts at 208/240 volts (22 amps) PLATE INDEX for rated power consumption. applicable Local and/or National Temperature Operating Range: Includes both o C and o F control dials SCREW 3.Do not remove the thermostat cover. Clean, attractive style suits any decore wall-mount design sits flush against wall Underwriters Laboratories Inc No.: E105830 BASE Canadian Standards Association No.: LR30410 SINGLE POLE THERMOSTAT INSTALLATION 2.Run line voltage wiring to the thermostat location. correct and tight to prevent electrical shorts. Use the should be entrusted to duly qualified personnel where The installation of the thermostat must comply with the Ensure that all wiring connections to the thermostat are 4.Connect the red LINE lead on the thermostat to the L1 1.Disconnect power supply to prevent electrical shock or Electrical Codes and utility requirements. This installation Mounts directly into a standard 2 x 4 inch vertical electrical BOX appropriate wire to meet local and national electrical codes Dimplex Line Voltage Electric Heat Thermostat OUTLET LOAD NOTE: WIRE BLACK WARNING WARNING CONNECTOR LINE RED of the heater. POWER SUPPLY the outlet box. the outlet box. L1 FROM product damage. thermostat base. leads on the heater. line lead on the heater. THERMOSTAT 12.Replace thermostat cover. for rated power consumption. the sensing device or wiring. the sensing device or wiring. using the two supplied screws. using the two supplied screws. line from the power supply panel. Do not over tighten mounting screws leads from the power supply panel. 3.Do not remove the thermostat cover. 8.Ensure that all connections are tight. 6.Ensure that all connections are tight. FROM the sides and pulling it away from the SUPPLY POWER NETURAL DOUBLE POLE THERMOSTAT INSTALLATION to duly qualified personnel where required by law. 2.Run line voltage wiring to the thermostat location. HEATER correct and tight to prevent electrical shorts. Use the 10.Mount the thermostat into the wall box and secure applicable Local and/or National Electrical Codes and The installation of the thermostat must comply with the Ensure that all wiring connections to the thermostat are 1.Disconnect power supply to prevent electrical shock or utility requirements. This installation should be entrusted 9.Remove the thermostat cover by grasping the cover by 6.Connect the N Neutral (or L2) line to the remaining line the sides and pulling it away from the thermostat base. 4.Connect the black LOAD leads on the thermostat to the 7.Secure the ground wire to the ground screw provided in 8.Secure the ground wire to the ground screw provided in 10.Remove the thermostat cover by grasping the cover by 11.Mount the thermostat base into the wall box and secure 5.Connect the red LINE leads on the thermostat to the line 5.Connect the black LOAD lead from the thermostat to the appropriate wire to meet local and national electrical codes 9.Insert wires into the outlet box taking care not to damage 7.Insert wires into the outlet box taking care not to damage NOTE: LOAD BLACK RED LINE OPERATION POWER SUPPLY L1 FROM heater will turn on. THERMOSTAT with the thermostat knob. INDEX PLATE REMOVAL RED 11.Replace thermostat cover. LINE LOAD BLACK SUPPLY POWER L2 FROM Do not over tighten mounting screws WIRE CONNECTOR clockwise will disconnect the power to the heater. on the heater. When the room reaches the desired turn clockwise until you hear the click again and the HEATER thermostat knob and push until the index plate is flush install line up the index plate pins with the holes in the clockwise will set the temperature rating to 5 o C (41 o F). turn the thermostat control clockwise all the way to turn until you hear a click. Leave in this position to maintain pry up on one of the slots located on the index plate. To For double pole models:-Turning the knob fully counter For single pole models:- Turning the knob fully counter temperature, turn the thermostat knob counter clockwise the room temperature at this setting. For additional heat, Using a small flat screwdriver or other suitable tool gently To adjust the temperature to your individual requirements, 7207610100rev00