Очаг DIMPLEX Opti-V (64907680). Инструкция на русском языке

Opti-V Fire
Модель: PGF10
Инструкции
UK          RU
08/52337/0      Issue 1
The product complies with the European Safety Standards EN60065 and the European Standard Electromagnetic Compatibility (EMC) EN55014-1 & EN55014-2,
EN6100-3-2 and EN6100-3-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC - Patents pending International Application
No. : PCT/EP2013/051263 & PCT/EP058211 GB Application : GB1210108.5

UK..........................................1
RU..........................................3

Opti-V Fire : PGF 10
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Introduction                                            Fixing dimensions
Thank you for chosing this Dimplex Opti-V ? re. Please read   The Opti-V is supplied in an assembled state.
information guide carefully to be able to safely install, use   This model is designed to be permanently fixed.
and maintain your product. The appliance is designed to be   Please see Fig.2a and 2b for recommended ? xing dimensions.
installed into a cabinet or wall opening.
Height of Fire
Important Safety Advice
When using electrical appliances, basic precautions should be   There is a choice of height when ? tting the ? re.
followed to reduce the risk of ? re, electric shock, and injury to   Recommended heights (from ? oor to bottom opening of ? re - *
persons, including the following:                       Fig 2a) :
If the appliance is damaged, check immediately with the supplier   - Minimum 65cm when the ? re is viewed while sitting
before installation and operation.                      (e.g. lounge).
Do not use this appliance in the immediate surroundings of a   - Maximum 110cm when the ? re is viewed while standing
bath, shower or swimming pool.
Means for disconnection must be incorporated in the ? xed wiring   (e.g. reception area).
in accordance with the wiring regulations.
Do not use outdoors.                                    Electrical connection
In the event of a fault switch off the appliance.       The outline of the chassis and the position of the electrical socket
Switch off the appliance when not required for long periods.  are shown as dotted outlines in Fig.4. Please consult  with a
If the supply cord is damaged, it must be replaced by a special   quali? ed electrician for appropriate wiring requirements.
cord or assembly available from the manufacturer or its service
agent.
Warning - No naked ? ame sources, such as candles, should be   Operation: -
placed on this apparatus.                               The power ‘ON’ switch (‘O/I’see Fig.3) must ? rst be switched ‘I’
Warning - The appliance shall not be exposed to dripping or   to operate the appliance.
splashing and that no objects ? lled with liquid, such as vases,   An ‘Opti-V’ screen will appear for about 3 seconds before the
shall be placed on the apparatus.                       ? ame picture starts .
Warning - this appliance is of Class I construction and must be   Note: The user may notice a blank screen for approximately 5
connected to a mains outlet with protective earthing connection.
seconds, every 30 minutes. This is normal and should not be a
cause for concern.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
Do not switch the appliance on until properly installed.  Please   Manual Control Operation: -
read all the safety warnings and operating instructions.  The manual controls for the screen are located at the inner top
left hand side of the appliance above the glass.(see Fig.3).
General                                                 The appliance Power switch (‘O/I’ see Fig.3) may be used to
Unpack the appliance carefully and retain the packaging for   switch the appliance off (‘O’) when it is not required,  for example,
possible further use, in the event of moving or returning the   overnight or for long periods, to avoid energy wastage.
appliance to the supplier.                              The standby button (    ) is located just below the mains switch.
Contents of Carton                                      Screen Brightness:-
•    Opti-V Fire Model PGF10                            The screen brightness can be adjusted using the    and
•    Remote control and batteries (AAA type)            buttons. These are located at the inner top, just above the glass
(see Fig.3). The   button darkens the screen and the     button
Product Features                                        brightens the screen.
Volume Control
Remote or Manual operation
Red light indication of standby mode                    Remote Control Operation: -
The remote control may be operated once the appliance is
Installation                                            switched ‘I’ (‘I’ see Fig.3).
Warning.                                                Aim the remote control at the ? re (the sensor is indicated in Fig.
Do not connect the appliance until properly ? xed to a secure   4). The volume may be adjusted up or down by pressing the
base and the instruction lea? et is read fully.         volume control buttons ( + and -).
At installation of the appliance, care must be taken not to   The button funtions are identi? ed as described below;
damage any cables that may be concealed in the wall.           Standby
-   Volume down
Positioning the Fire                                      +   Volume up
The Opti-V uses an illusory re? ection technique and is designed   A red light will indicate when the appliance is in standby mode.
to work best when ambient light levels are low. If the Opti-V is   (see Fig 4)
installed in brightly lit areas, the strong re? ections may diminish
the ? ame picture.
1