Углошлифовальная машина FELISATTI AG125/1400CSE. Инструкция на русском языке

AG125/1400SIV
AG125/1400SIVE
WINKELSCHLEIF MASHINE
УГЛОВАЯ ШЛИФОВАЛЬНАЯ МАШИНА

MACHINE-SPECIFIC SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire  m) Do not run the power tool while carrying it at your side.
Brushing or Abrasive Cutting-Off Operations:  Accidental contact with the spinning accessory could snag
a)  This  power tool  is intended  to  function  as  a  grinder,   your clothing, pulling the accessory into your body.
sander, wire brush, or cut-off tool. Read all safety warnings,   n) Regularly clean the power tool’s air vents. The motor’s
instructions, illustrations and specifications provided with this   fan will draw the dust inside the housing and excessive
power tool. Failure to follow all instructions listed below may   accumulation of powdered metal may cause electrical
result in electric shock, fire and/or serious injury.  hazards.
b)  Operations such as polishing are  not recommended to   o) Do not operate the power tool near flammable materials.
be performed with this power tool. Operations for which the   Sparks could ignite these materials.
power tool was not designed may create a hazard and cause   p) Do not use accessories that require liquid coolants. Using
personal injury.                     water or other liquid coolants may result in electrocution or
c) Do not use accessories which are not specifically designed   shock.
and recommended by the tool manufacturer. Just because   Kickback and related warnings
the accessory can be attached to your power tool, it does not   Kickback is a sudden reaction to a pinched or snagged
assure safe operation.               rotating wheel.
d )The rated speed of the accessory must be at least equal to   Pinching or snagging causes rapid stalling of the rotating
the maximum speed marked on the power tool. Accessories   wheel which in turn causes the uncontrolled power tool to be
running  faster  than  their  rated  speed  can  break  and  fly   forced in the direction opposite of the wheel‘s rotation at the
apart.                               point of the binding.
e) The outside diameter and the thickness of your accessory   For example, if an abrasive wheel is snagged or pinched by
must be within the capacity  rating of your power tool.    the workpiece, the edge of the wheel that is entering into the
Incorrectly sized accessories cannot be adequately guarded   pinch point can dig into the surface of the material causing
or controlled.                       the wheel to climb out or kick out. The wheel may either jump
f) The arbour size of wheels, flanges, backing pads or any   toward or away from the operator, depending on direction
other accessory must properly fit the spindle of the power   of the wheel’s movement at the point of pinching. Abrasive
tool. Accessories with arbour holes that do not match the   wheels may also break under these conditions.
mounting hardware of the power tool will run out of balance,   Kickback  is  the  result  of  saw  misuse  and/or  incorrect
vibrate excessively and may cause loss of control.  operating procedures or conditions and can be avoided by
g) Do not use a damaged accessory. Before each use inspect   taking proper precautions as given below.
the accessory such as abrasive wheels for chips and cracks,   a) Maintain a firm grip on the power tool and position your
backing pad for cracks, tear or excess wear, wire brush for  body and arm to allow you to resist kickback forces. Always
loose or cracked wires. If power tool or accessory is dropped,   use auxiliary handle, if provided, for maximum control over
inspect for damage or install an undamaged accessory. After   kickback  or  torque reaction during start-up.  The operator
inspecting and installing an accessory, position yourself and   can control torque reactions or kickback  forces, if proper
bystanders away from the plane of the rotating accessory   precautions are taken.
and run the power tool at maximum noload speed for one   b) Never place your hand near the rotating accessory.
minute. Damaged accessories will normally break apart   Accessory may kickback over your hand.
during this test time.               c) Do not position your body in the area where power tool
h) Wear personal protective equipment. Depending on   will move if kickback occurs. Kickback will propel the tool in
application,  use face shield, safety goggles or safety   direction opposite to the wheel’s movement at the point of
glasses.                             snagging.
As appropriate, wear dust mask, hearing protectors, gloves  d) Use special care when working corners, sharp edges, etc.
and shop apron capable of stopping small abrasive or  Avoid bouncing and snagging the accessory. Corners, sharp
workpiece fragments. The eye protection must be capable of  edges or bouncing have a tendency to snag the rotating
stopping flying debris generated by various operations. The   accessory and cause loss of control or kickback.
dust mask or respirator must be capable of filtrating particles   e) Do not attach a saw chain, woodcarving blade or toothed
generated by your operation. Prolonged exposure to high   saw blade. Such blades create frequent kickback and loss
intensity noise may cause hearing loss.  of control.
i) Keep bystanders a safe distance away from work area.   Safety Warnings Specific for Grinding and Abrasive Cutting-
Anyone entering the work area must wear personal protective   Off Operations:
equipment. Fragments of workpiece or of a broken accessory   a) Use only wheel types that are recommended for your
may fly away and cause injury beyond immediate area of   power tool and the specific guard designed for the selected
operation.                           wheel. Wheels for which the power tool was not designed
j)  Hold  power  tool  by  insulated  gripping  surfaces,  when   cannot be adequately guarded and are unsafe.
performing an operation where the cutting accessory  may   b) The guard must be securely attached to the power tool
contact  hidden wiring or its own cord. Cutting accessory   and positioned for maximum safety, so the least amount
contacting a „live“ wire may make exposed metal parts of   of wheel is exposed towards the operator. The guard helps to
the power tool „live“ and could give the operator an electric   protect operator from broken wheel fragments and accidental
shock.                               contact with wheel.
k) Position the cord clear of the spinning accessory. If you   c) Wheels must be used only for recommended applications.
lose control, the cord may be cut or snagged and your hand   For example: do not grind with the side of cut-off wheel.
or arm may be pulled into the spinning accessory.  Abrasive cut-off wheels are intended for peripheral grinding,
l) Never lay the power tool down until  the accessory  has   side forces applied to these wheels may cause them to
come to a complete stop. The spinning accessory may grab   shatter.
the surface and pull the power tool out of your control.  d) Always use undamaged wheel flanges that are of correct
3

size and shape for your selected wheel. Proper wheel   in order to find out the cause.
flanges  support  the  wheel  thus  reducing  the  possibility  of   Always use and store the grinding disks according to the
wheel breakage.                      manufacturer’s instructions.
Flanges  for cut-off wheels  may  be different from  grinding   When grinding metal, flying sparks are produced. Take care
wheel flanges.                       that no persons are endangered. Because of the danger of
e) Do not use worn down wheels from larger power tools.  fire, no combustible materials should be located in the vicinity
Wheel intended for larger power tool is not suitable for the   (spark flight zone). Do not use dust extraction.
higher speed of a smaller tool and may burst.  Due care should be taken that no sparks or sanding dust
Additional Safety Warnings Specific for Abrasive Cutting-Off   flying from the workpiece come into contact with you.
Operations:                          When separating stone the guide shoe must be used!
a) Do not “jam” the cut-off wheel or apply excessive pressure.   The adjusting nut must be tightened before starting to work
Do not attempt to make an excessive depth of cut.  with the machine.
Overstressing  the wheel increases the loading and   The workpiece must be fixed if it is not heavy enough to be
susceptibility to twisting or binding of the wheel in the cut and   steady. Never lead the workpiece to the grinding disk with
the possibility of kickback or wheel breakage.  your hand.
b) Do not position  your body in line with and behind the   Under extreme conditions (e.g. smooth-grinding metals with
rotating wheel. When the wheel, at the point of operation, is  the arbour and vulcanized fi bre grinding wheel), signifi cant
moving  away from your body, the possible kickback  may   contamination can build up on the inside of the angle grinder.
propel the spinning wheel and the power tool directly at you.  For safety reasons, in such conditions the inside should be
c) When wheel is binding or when interrupting a cut for any  cleaned thoroughly of metal deposits and a residual current
reason, switch off the power tool and hold the power tool   device (FI, RCD, PRCD) must be connected in series. If the
motionless until the wheel comes to a complete stop. Never  residual current device responds, the machine must be sent
attempt to remove the cut-off wheel from the cut while the   for repair.
wheel is in motion otherwise kickback may occur. Investigate   For  accessories  intended  to  be  fi  tted  with  threaded  hole
and take corrective action to eliminate the cause of wheel   wheel, ensure that the thread in the wheel is long enough to
binding.                             accept the spindle length.
d) Do not restart the cutting operation in the workpiece. Let   When cutting-off material, use the closed safety guard from
the wheel reach full speed and carefully reenter the cut. The   the accessories range.
wheel may bind, walk up or kickback  if the power tool is
restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large workpieces
tend to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket cut” into existing
walls or other blind areas. The protruding wheel may cut gas
or  water  pipes,  electrical  wiring  or  objects  that  can  cause
kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc paper.
Follow manufacturers  recommendations,  when selecting
sanding paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
Safety Warnings Specific for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do  not overstress the wires by
applying excessive load to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing, do
not allow any interference of the wire wheel or brush with
the guard. Wire wheel or brush may expand in diameter due
to work load and centrifugal forces.
Appliances used at many different locations including open
air should be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Sawdust  and splinters must not be removed while the
machine is running.
Only plug-in when machine is switched off.
Never reach  into  the danger  area of the plane  when it is
running.
Always use the auxiliary handle.
Always use the protecting cap when roughing-down and
separating.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine
4