Измеритель влажности ADA ZFM 100-4. Инструкция на русском языке

Operating manual
Non-Invasive Inductive MoistureMeter
Model: ZFM 100-4
Manufacturer                             Address: WWW. ADAINSTRUMENTS.COM

        ZFM 100-4
Table of contents
1. Introduction .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  3
2. Appearance .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4
3.  Functions    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    5
4. Operation instructions  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5
5. Technical data  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  8
6. Warranty/Exceptions from responsibility .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . .  .  .  .  .  .   .  .  .  .  .  .  .  .  .  .  .  .  9
Appendix 1. Certificate of acceptance and sale
Appendix 2. Warranty card

ZFM 100-4
INTRODUCTION
ZFM 100-4 Non-Invasive Inductive Moisture Meter main by the sensor , at the back of the tool, emits and picks up electro-magnetic sig-
nals through the material to be tested. The reading displayed is an average value of the moisture content from the entire surface area and
the maximum depth of penetration. Moisture which is closer to the surface has a greater effect on the average value than the moisture close
to the maximum depth of penetration. ZFM 100-4 has internal auto-calibration function, therefore no need for manually calibration.
If the target depth is smaller than Max. measuring range 20mm, the value shows on the LCD is not accurate. The Max measuring depth
for this unit is 3/4 inch (20mm).
Notes:
The measured  values of  drywall and masonry are relative. Moisture degree is displayed  in conditional units. Relative measurements
allow to control the change of humidity in the materials during the time. E.g. the process of drying out of plaster before laying the fol-
lowing layer.