Микроскоп OLYMPUS FV10i-DOC. Инструкция на английском языке

FLUOVIEW
FV10i-DOC
&RQIRFDO /DVHU 6FDQQLQJ %LRORJLFDO 0LFURVFRSH
? 7KLV LQVWUXFWLRQ PDQXDO LV IRU WKH 2O\PSXV &RQIRFDO /DVHU 6FDQQLQJ %LRORJLFDO 0LFURVFRSH
0RGHO )/829,(: )9  L '2&
7R HQVXUH WKH VDIHW\  REWDLQ RSWLPXP SHUIRUPDQFH DQG IDPLOLDUL]H \RXUVHOI IXOO\ ZLWK WKH
XVH  RI  WKLV  PLFURVFRSH   ZH  UHFRPPHQG  WKDW  \RX  VWXG\  WKLV  PDQXDO  WKRURXJKO\  EHIRUH
RSHUDWLQJ WKH PLFURVFRSH  )RU VDIHW\  ZH DOVR UHFRPPHQG WKDW \RX UHDG DWWDFKHG 86(5b6
0$18$/ >6$)(7<@ WRJHWKHU ZLWK WKLV PDQXDO
? )RU  WKH  RSHUDWLQJ  SURFHGXUHV  IRU  REVHUYDWLRQ  DQG  DFTXLVLWLRQ   SOHDVH  DOVR  UHDG  VHSDUDWH
YROXPH >6LPSOLrHG 2SHUDWLRQ 0DQXDO@ DQG WKH 2QOLQH +HOS RI WKH VRIWZDUH
? 5HWDLQ WKLV LQVWUXFWLRQ PDQXDO LQ DQ HDVLO\ DFFHVVLEOH SODFH QHDU WKH ZRUN GHVN IRU IXWXUH
UHIHUHQFH
A X 8 0 1 9  [TYPE 3]

FLUOVIEW FV10i-DOC
CONTENTS
IMPORTANT                                                                            1
1    SYSTEM AND MAIN CONTROLS                                                      2-4
2    ASSEMBLY                                                                      5,6
1   Connecting the Cables................................................................................................................................................................  5
2   Placing the Specimen ...................................................................................................................................................................  6
3    USING THE IMMERSION OIL                                                         7
1   Attaching Immersion Oil.............................................................................................................................................................  7
2   Removing Immersion Oil...........................................................................................................................................................  7
3   Draining Water from the Water Tray ..........................................................................................................................  7
PROPER SELECTION OF THE POWER SUPPLY CORD ............................................................................  8,9

IMPORTANT
For safety precautions, please refer to attached USER’S MANUAL
[ SAFETY ].
1    Getting Ready
1. Three forms of specimen (containers) can be used including a  35 mm glass-bottom dish, slide glass (76 mm x 26 mm)
and well slide (8 compartments). The standard thickness of the cover glass is 0.17 mm, but the range from 0.13 to 0.21 mm
is acceptable.
2. The operating period warranted for the LD light source is the shorter period of 2000 hours or one (1) year after the delivery
inspection.
3. When 4 hours have elapsed since the power was turned on or depending on the fluctuation of the temperature in the
usage environment, a drift may occur in the X, Y or Z direction.
4. Do not apply strong impact to the equipment.
5. Reserve clearances of 15 cm or more in front of the air inlet and outlet.
6. If water drops are left on the inner side of the top cover of the  35 mm glass-bottom dish, the quality of the transmitted
image may be degraded.
7. When a high-power objective is switched to a low-power objective, the image quality may be degraded due to immersion
oil attached at the bottom side of the specimen.
8. The Z-stack image can be obtained only in the direction from the position distant to the specimen toward the position
closer to it.
Long-period oscillations (20 Hz or less) may affect the image quality.
9. To disinfect the main unit and specimen holder, wipe them with clean cloth moistened with disinfectant ethanol.
10. When disposing of the microscope, be sure to observe the regulations or rules of your local government.
2    Caution
If the equipment is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the
equipment may also be damaged. Always use the equipment as outlined in this instruction manual.
1