Аппарат плазменной резки FUBAG Plasma 20 AIR. Инструкция на русском языке

Operator's  manual
www.fubag.ru
WARNING! BEFORE USING THE WELDING MACHINE READ THE INSTRUCTION
MANUAL CAREFULLY! FOR QUALIFIED AND SPECIALLY TRAINED PERSONS
ONLY AFTER PROPER READING OF THIS MANUAL IS ALLOWED TO USE AND TO
MAINTAIN THIS MACHINE.
The detailed description, safety rules and all required information necessary for proper operation
and maintenance of FUBAG machine are provided below. Keep this instruction manual by machine
and refer to it by any doubts concerning safety operation, maintenance storage and handling of
FUBAG machine.
1. Safety perationo
- It is highly recommended always to follow the safety rules. Wear protective clothes and
special means to avoid injuries to eyes and skins.
- Prevent the sparks and spatter from harming your body.
- Do not operate under water or more humid place.
- Make sure to work in places where there are exhaust or ventilation facilities to keep fumes
or emissions away from the breathing zone.
- No touching on the electrification parts after turning on the power. Cut off the power supply
after operation or before leaving the welding site.
- Safe measures should be adoptted while operating in high place to avoid accident.
- No entering the welding site for persons not concerned.
WARNING. The voltage is always higher, so the safety precaution should be taken before
repair to avoid accidental shock. Switch off the power supply before each type of
maintenance work. The untrained people are not allowed to make maintenance of the
machine.
- 1 -

Operator's  manual
www.fubag.ru
- Maintenance should be conducted by the trained personnel.
- When the  plasma is used outdoors, it should be kept from rain or long exposure to the sun.
- Check is needed from time to time to make sure the cable is in good condition if the
machine is in frequent use. Check at least once each month if the  plasma is in regular use. It
is necessary to check when the  plasma is in mobile use.
- Dust removal is needed every year. Check the machine's fasteners, moving-iron, current
regulation screws, etc to make sure there are no loose connection problems.
- The dust, acid and erodible dirt in the air at the job site can not exceed the amount required
by the norm.
- The welder must be installed in the place where it can not be exposed to sun and rain. Also it
must be stored in less humid place with the temperature.
- Make sure that there is no metal-like foreign body to enter the machine.
- No violent vibration in the welder's surrounding area.
- Make sure that there is no interference with the surrounding area at the installation site.
Safety Check:
Each item listed below must be carefully checked before operation:
- Make sure that there is no short circuit connection with welder's both outputs.
- Make sure that there is always sound output and input wire connection instead of exposing it
outside.
Regular check needs to be conducted by the qualified personnel after the machine has been
installed over a long period or re-operation, which involves as follows:
- Check the cable to see if it can continue to be used before it is worn out.
- Replace the input cable as soon as it is found to be broken or damaged.
- Make sure whether there is enough power supply to make the welding machine work properly.
Any power source required to access the machine must be installed with some protective
equipments.
Please do not hesitate to contact us for technical assistance whenever you come across the
problems you can not work out or you may deem difficult to fix.
- 2  -

Operator's  manual
www.fubag.ru
2. Technical pecificationss
MODEL                 PLASMA 20 AIR        PLASMA 30 LV
Rated voltage/frequency, V/Hz  220/50              85-265/50
Max. input power, kW          3,5                 3,68
Max. input current, А        16                   16
Current, А                5-20                5-30
Current of duty cycle %, А    20 at 34            30 at 32
Max. cutting thickness steel, mm  6                   10
Max. cutting thickness aluminium, mm  4                 8
Capacity, l/min             40                   115
Pressure, bar               3                  2,5-6
IP                                IP23
Dimension, mm            480х220х360          410х185х290
Weight, kg                18,5                 12
Ambient temperature, °С                -10…+40
Relative humidity, %         at 20°С up to 90%; at 40°С up to 50%
diffuser, 2 electrodes, 2 tips, air
Acessories            2 electrodes, 2 tips
connector
The manufacturer reserves himself the right to make the manual's content or function change
without any preliminary notification of the users.
3. Description е
Fubag Plasma are inverter plasma cutters, portable, single phase, ventilated. They enable to cut in
direct current (DC) steel, stainless steel, aluminium, copper. They work with a single phase input
220V (Plasma 30 LV - spread between 85V to 265V ).
8
1. Current setting
2. Power indicator
5                                               3. Thermal protection indicator
4. Manometer (only
2               3             Plasma 30 LV)
5. Pressure regulator (only
Plasma 30 LV)
6. Torch
1                                 7. E arth clamp
6                                                8.  Compressor with filter
(only Plasma 0
2 AIR)
4
7
- 3 -