Видеомагнитофон SONY SLV-EZ77AS. Инструкция на английском языке

3-058-426-12  (1)
Video Cassette
Recorder
Operating Instructions
SLV-EZ77AS/EZ77NZ
PAL NTSC
SLV-EZ66AZ
PAL NTSC 4.43
© 2000 by Sony Corporation

WARNING                             Caution
Television programmes, films, video tapes and
To prevent fire or shock hazard, do not expose  other materials may be copyrighted.
the unit to rain or moisture.       Unauthorized recording of such material may
To avoid electrical shock, do not open the  be contrary to the provisions of the copyright
cabinet. Refer servicing to qualified personnel  laws. Also, use of this recorder with cable
only.                               television transmission may require
The mains lead must only be changed at a  authorization from the cable television
qualified service shop.             transmitter and/or programme owner.
Precautions                         Compatible colour systems
• Check the colour systems of your VCR using
Safety                                the table below.
• This unit operates on 220-240 V AC, 50 Hz.
Check that the unit’s operating voltage is  Model number  Colour system
identical with your local power supply.           Recording  Playback
• If anything falls into the cabinet, unplug the
unit and have it checked by qualified  SLV-EZ77AS/  PAL     PAL
personnel before operating it any further.  EZ77NZ  NTSC 4.43  NTSC 4.43
• The unit is not disconnected from the mains
as long as it is connected to the mains, even     NTSC 3.58  NTSC 3.58
if the unit itself has been turned off.  SLV-EZ66AZ  PAL    PAL
• Unplug the unit from the mains if you do                    NTSC 4.43
not intend to use it for an extended period of
time. To disconnect the lead, pull it out by  Recording of video sources based on other
the plug, never by the lead.        colour systems cannot be guaranteed.
• (For SLV-EZ77AS/EZ77NZ only)
Installing                            NTSC colour signals can only be recorded
• Allow adequate air circulation to prevent  through the line inputs.
internal heat buildup.
• Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation
slots.
• Do not install the unit near heat sources
such as radiators or air ducts, or in a place
subject to direct sunlight, excessive dust,
mechanical vibration or shock.
• Do not install the unit in an inclined
position. It is designed to be operated in a
horizontal position only.
• Keep the unit and cassettes away from
equipment with strong magnets, such as
microwave ovens or large loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to
a warm location, moisture may condense
inside the VCR and cause damage to the
video head and tape. When you first install
the unit, or when you move it from a cold to
a warm location, wait for about four hours
before operating the unit.
2  Introduction

Table of contents
Getting Started
4   Step 1:Unpacking
5   Step 2: Setting up the remote commander
9   Step 3: Connecting the VCR
11 Step 4: Tuning your TV to the VCR                                   Getting Started
13 Step 5: Setting the clock
15 Step 6: Presetting channels with the EASY G-CODE SET UP function
17 Presetting channels
23 Setting up the G-CODE* system manually
26 Changing/disabling programme positions
Basic Operations                57 Searching using the index
function
30 Playing a tape
59 Adjusting the picture
34 Recording TV programmes
61 Changing menu options
37 Recording TV programmes using
the Easy Timer function
43 Recording TV programmes using        Editing
the G-CODE system
62 Connecting to a VCR or stereo
46 Setting the timer manually           system
63 Basic editing
Additional Operations           64 Audio dubbing (SLV-EZ77AS/
EZ77NZ only)
48 Playing/searching at various
speeds
49 Setting the recording duration       Additional Information
time
65 Troubleshooting
50 Synchronised recording
69 Specifications
52 Checking/changing/cancelling
timer settings                  70 Index to parts and controls
Back cover
54 Recording stereo and bilingual
programmes                          Index
56 Searching the beginning of an
Easy Timer recorded programme
* G-CODE is a registered trademark of Gemstar Development Corporation.  The G-CODE system
is manufactured under license from Gemstar Development Corporation.
Introduction  3