Универсальный пульт ДУ PHILIPS SRU5010. Инструкция на русском языке

SRU 5010/87
GB  Instructions for use   4
I  Instruzioni per l'uso 10
Instrucciones
E                  16
de manejo
P  Manual de utilizacao 22
GR  Od
 	
  28
Инструкции по
RU                 34
использованию
CZ  Navod k pouziti  40
PL  Instrukcja obslugi  46
Quick, Clean & Easy Setup
www.philips.com/urc

Instructions for use
Contents
1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.  Installing the remote control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
English
Inserting the batteries  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Testing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.  Keys and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.  Extra possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Adding a function to the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Restoring the original functions of your remote control  . . . . . . . . . . . . . 8
5.  Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.  Need help? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Code list of all brands / equipment  . . . . . . . . . . . . . . . . . . . . . . . . . . 52-60
Information to the Consumer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
1. Introduction
Congratulations on your purchase of the Philips SRU 5010 universal remote
control. After installing the remote control it can operate the most-used
functions of almost any brand of TV.
You can find information about how to prepare this remote control for use in
the chapter ‘Installing the remote control’.
2. Installing the remote control
Inserting the batteries
1   Press the cover inwards and slide it in
the direction of the arrow.
2   Place two AAA type batteries into the
battery compartment, as shown.
3   Slide the cover back and click it firmly into
place.
Note: If the LED blinks four times after every key press, the remote control is indicating
that its batteries are running low. Replace the old batteries with two new AAA
batteries.
Testing the remote control
The remote control has been programmed to operate the most-used
functions of almost any brand of TV. Because the SRU 5010 may use different
signals for each make and even for different models of the same brand, it is
advisable to test whether your TV responds to the SRU 5010.
The example below instructs you how to do this.
1   Turn your TV on manually or use the original remote control.
Tune to channel 1.
2   Check whether all the keys are working
For an overview of the keys and their
functions see ‘3. Keys and functions’.
–   If the TV responds as it should to all of the
key commands the SRU 5010 is ready for use.
•   If the TV does not respond at all or not to all of the
key commands, follow the instructions under
‘Setting the remote control’, or for online setup go to:
www.philips.com/urc.
4

Instructions for use
Setting the remote control
This is only necessary if your TV does not respond to the SRU 5010.  English
If that is the case, the SRU 5010 does not recognize the brand and/or model
of your TV and you need to program the remote control to do so.
You can set the remote control either automatically or manually.
Automatically setting the remote control
The remote control will now automatically search for the right code for your
device.
1  Make sure the TV is switched on and select a channel using the original
remote control or the keys on the TV (for example channel 1).
The SRU 5010 emits the ‘switch off TV’ signal for all models of TV that
are stored in the memory.
2  Then keep keys 1 and 3 on the SRU 5010
pressed simultaneously for three seconds,
until the LED flashes twice and then remains
lit.
3  Press and hold the Standby key
of the SRU 5010.
–  The SRU 5010 now starts emitting all known
‘TV off’ signals, one by one.
Each time a code is sent, the LED
lights up
4  When your TV switches off (stand-by), release
the Standby key of the SRU 5010 immediately.
–  The SRU 5010 has now found a code that works on your TV.
5  Check if you can operate all functions on your TV with the SRU 5010.
•  If this is not the case, you can redo the automatic setting.
The SRU 5010 will then search for a code that works better.
–  After the SRU 5010 has run through all the known codes,
the search will stop automatically and the LED will stop flashing.
–  Automatic programming of a TV takes a maximum of 5 minutes.
5