Универсальный пульт ДУ PHILIPS SRU4010. Инструкция на русском языке

SRU 4010/10
GB  Instructions for use   4
FR  Mode d'emploi         7
DE  Bedienungsanleitung  10
NL  Gebruiksaanwijzing   13
DK  Vejledning           16
SV  Bruksanvisning       19
NO  Bruksanvisning       22
SF  Kayttoohje           25
IT  Instruzioni per l'uso  28
ES  Instrucciones de manejo  31
PR  Manual de utilizacao  34
GR  Od
 	
      37
RU  Инструкции по
использованию         40
CZ  Navod k pouziti      43
PL  Instrukcja obslugi   46
TR  Kullanma talimatlar?  49
Quick, Clean & Easy Setup
www.philips.com/urc

Instructions for use
Contents
1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
English
2.  Installing the remote control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Testing the remote control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
3.  Keys and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Code list of all brands / equipment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-58
Information to the Consumer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
1. Introduction
Congratulations on your purchase of the Philips SRU 4010 universal remote control.
After installing the remote control it can operate the most-used functions of almost any
brand of TV.You can find information about how to prepare this remote control for use in
the chapter ‘Installing the remote control’.
2. Installing the remote control
Inserting the batteries
1   Press the cover inwards and slide it in the direction
of the arrow.
2   Place two AAA type batteries into the battery
compartment, as shown.
3   Slide the cover back and click it firmly into place.
Testing the remote control
The remote control has been programmed to operate most Philips devices. Because the
SRU 4010 may use different signals for each brand and even for different models of the
same brand, it is advisable to test whether your TV responds to the SRU 4010.
The example below instructs you how to do this.
1   Turn your TV on manually or use the original remote control.Tune to channel 1.
2   Check whether all the keys are working.
For an overview of the keys and their functions,
see ‘3. Keys and functions’.
–   If the TV responds as it should to all of the key commands
the SRU 4010 is ready for use.
•   If the TV does not respond at all or not to all of the key commands, follow
the instructions under ‘Setting the remote control’, or for online setup go to:
www.philips.com/urc.
Setting the remote control
This is only necessary if your TV does not respond to the SRU 4010.
If that is the case, the SRU 4010 does not recognize the brand and/or model of your TV
and you need to program the remote control to do so.
You can set the remote control either automatically or manually.
4

Instructions for use
Manually setting the remote control
English
1  Turn on the TV manually or use the original remote control.Tune in to channel 1.
2  Look up the brand of your TV in the code list at
the back of this manual. One or more four-figure codes are
shown for each brand. Note the first code.
On our website www.philips.com/urc you can directly select your
device typenumber to find the right code.
3  Use a pen or paper clip to press the Setup key and
keep it pressed for 5 seconds until the Standby key blinks
twice and then remains lit.
4  Then enter the code noted in step 2, using the digit keys.
–  The Standby key will now blink twice. If the key blinks once
for an extended period, the code has not been entered
properly or the wrong code has been entered.
Start again from step 2.
5  Point the SRU 4010 at the TV and check that it responds as it should.
–  If the TV responds to all of the key commands, the SRU 4010 is ready for use.
Do not forget to note your code.
•  If the device does not respond at all, or not to all of the key commands, start
again from step 2 and try the next code from the list.
Automatically setting the remote control
The remote control will now automatically search for the right code for your device.
1  Make sure the TV is switched on and select a channel using the original remote
control or the keys on the TV (for example channel 1).
2  Use a pen or paper clip to press the Setup key and
keep it pressed for 5 seconds until the Standby key blinks
twice and then remains lit.
3  Press the Standby key of the SRU 4010 and
keep it pressed.
–  The SRU 4010 now starts emitting all known ‘TV off’
signals, one by one. Each time a code is sent, the Standby
key lights up.
5