На сайте 124208 инструкций общим размером 502.85 Гб, которые состоят из 6278960 страниц

Медиаплеер POPCORN HOUR A-210 upgradekit. Инструкция на русском языке

Руководство пользователя POPCORN HOUR A-210 upgradekit. Основные функции, характеристики и условия эксплуатации изложены на 2 страницах документа в pdf формате.

Информация

Раздел
Электроника
Категория
Медиаплееры
Тип устройства
Медиаплеер
Производитель (бренд)
POPCORN HOUR
Модель
POPCORN HOUR A-210 upgradekit
Еще инструкции
Медиаплееры POPCORN HOUR, Медиаплееры POPCORN HOUR
Язык инструкции
русский
Дата создания
17 Ноября 2021 г.
Просмотры
126 просмотров
Количество страниц
2
Формат файла
pdf
Размер файла
873.11 Кб
Название файла
popcorn_hour_manual_a_210_upgradekit.pdf

Фото

Страница 1Страница 2

Просмотр

Доступно к просмотру 2 страницы. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.

  • A-210 Upgrade Kit Hard Disk Installation Guide
    Steps Installation
    Installation Guide for Popcorn Hour A-210 aluminum case
    Popcorn Hour A-200  Philips head screw driver       RoHS              Networked Media Tank                                                                                            412000800075  0006DC807015  Pass  QC
    Long nose Plier     Step 1                                   Step 2                                   Step 3                                   Step 4
    Popcorn Hour A-210 case
    Flip the A-200 over to show it’s underside.   Turn the A-200 so that the top logo is facing you.   Inside the A-200, remove the screw on the right   Remove the PCB from A-200 case.
    Remove the 2 screws located at the front of the   Grasp the lid at the back of the device and gently   of the plastic HDD tray. Gently side the tray to   1. Unscrew 3 screws holding the PCBA to
    device near the rubber pads, then remove the 3   lift it towards you. The lid will come free with a   the right to remove it.      the case.
    screws located at the back of the devive at the   loud click. Set the lid aside.                                           2. Lift up the PCBA but be careful of the
    Heat-sink  LED Guide  PCB Spacer  Screws  Thermal Rubber  protruding ledge.                                                                                                     connector connecting the extension board.
    25.5 cm (H)  What you need:
    1. Popcorn Hour A-200
    2. Popcorn Hour A-210 case
    3. Philips head screw driver
    4. Long nose Plier
    Found in contents of A-210 case upgrade kit                   Pass  QC
    1. Heat-sink
    2. Thermal Rubber 50x50x2.6mm                                 412000800075  0006DC807015
    3. Thermal Rubber 27x27x2.8mm                                          front                                     rear                      ETHERNET  HDMI  USB  USB-PC  S-VIDEO  S/PDIF  AUDIO OUT  CVBS  COMPONENT VIDEO
    4. Thermal Rubber 27x27x1.6mm                       JAPAN                                                                                POWER  ACT          LNK  OPTICAL  COAX  L  R  Pr  Pb  Y
    5. LED Guide                                                                                 6
    6. PCB Spacer                                                                                                  RoHS
    7. Screws for LED Guide                                                                            side
    8. Screws for PCB Spacer
    9. Screws for heat-sink                                                back
    Step 5                                   Step 6                                   Step 7                                   Step 8
    Remove fan from PCBA.                    Preparing the A-210 upgrade kit.         Remove the top cover of A-210 case.      Applying thermal rubber to case.
    1. Disconnect the fan power pin.         1. Remove 3 screws from both sides of the A-210        1. With all the required screws removed, lift up   (require Thermal Rubber 27x27x1.6mm packet)
    2. Flip the PCBA and locate 2 pin as shown, use       case as shown. DO NOT remove the  4th screw,       the bottom piece carefully.  1. Remove thermal rubber from packet, peel off
    a plier to squeeze the pin out carefully.      crossed out in the diagram.                                                 protective transparent seal from both side.
    3. The fan should pop out now, you may place   2. Remove 1 screw from the back panel.                                      2. Apply it to the case as shown above.
    the fan aside.                       3. Flip the case and remove 2 screws from side.
    38 cm (W)
  • A-210 Upgrade Kit Hard Disk Installation Guide
    0006DC807015  412000800075
    0006DC807015
    QC    412000800075
    Pass
    QC  Pass
    Step 9                                            Step 10                                           Step 11                                           Step 12
    Installing heat-sink to PCBA.                     PCB Spacer installation.                          Installing the PCBA to case                       Secure heat-sink with screws from screw from
    (require thermal rubber 27x27x2.8mm and heat-sink)  (require PCB spacer packet and PCB spacer screws packet)   (required PCB spacer screw and PCBA screw)  heat-sink packet.
    1. Remove thermal rubber from packet, peel off protective   1. Remove spacer from PCB Spacer packet, and insert   1. Align the PCBA to the extension board pin as above
    seal.                                             into the case by using the 2 guiding pin.         carefully, slot it in making sure that it is tight.
    2. Paste thermal rubber on CPU as shown.          2. Take a screw from LED Guide & PCB Spacer packet.  2. The PCBA ports should align with the back panel.
    3. Align heat-sink pin to the pin hole on PCBA, and snap   3. Flip the case over and secure the spacer using screw.  3. Once align, use the screws from Screw for 2.5” HDD
    it in.                                                                                              & PCBA packet and Screw for PCB Spacer packet.
    4. Ensure that the heat-sink is snapped in, and properly                                            4. Secure all 4 screw hole location with the appropriate
    align for maximum heat-dissipation.                                                                 screw size.
    25.5 cm (H)                                                                                        front
    developed by
    gy in US and Malaysia.
    QC  Pass
    back
    Step 13                                           Step 14                                           Step 15                                           Step 16
    Paste thermal rubber from thermal rubber 50x50x2.6mm   Installing LED Guide from LED guide packet and 2   Closing the A-210 case.                     Completing the installation
    packet on top of heat-sink.                       screws from LED Guide & PCB spacer packet.        1. Place the top case as shown above, ensure that the   1. Slide the top case to close it.
    1. Align LED guide as shown to the PCBA, flip over       bottom case is cover completely by the top case   2. Complete installation by assembling the case
    the case and secure 2 screws.                     before closing.                                   together.
    38 cm (W)

Скачать инструкцию

Файл скачали 17 раз (Последний раз: 28 Января 2024 г., в 22:09)

Загрузить

Инструкции к похожим моделям