Стереосистема SHARP GX-BT3. Инструкция на английском языке

If you require any advice or assistance
regarding your Sharp product, please visit
our web-site www.sharp.co.uk/support
Customers without internet access may
MODEL                                        telephone 0845 880 0512 during office
GX-BT3                                       hours (or (01) 676 0648 if telephoning from
Ireland).
WIRELESS BLUETOOTH  SPEAKER SYSTEM
®
This Quick Start Guide will help you to correctly install and  operate your system.
1  Accessories
STAND-BY ON/
ECO MODE
MUTE  VOL
TREBLE  X-BASS
BASS
PAIRING  AUDIO IN
BLUETOOTH
DIMMER
RRMCGA342AWSA
GX-BT3
Remote control x 1  NFC tag x 2  Velcro tape   Velcro tape
(hook type) x 2  (loop type) x 3
2  Power source
Wall socket
AC 100 - 240 V ~
50/60 Hz
3  Before using remote control 4  Turn on your system
Before using the remote control, remove   Press the ON/STAND-BY button to turn the
the plastic shield from the battery holder.  power on.
ON/
Remote control      Plastic shield              STAND-BY
ON/
MUTE  ECO MODE  STAND-BY
BASS  TREBLE  VOL
PAIRING  X-BASS
BLUETOOTH  AUDIO IN
Battery holder            DIMMER             GX-BT3
RRMCGA343AWSA
*TINSEA457AWZZLA*|
TINSEA457AWZZ                                                        13J R KI 1
2013-0
GX-BT3_QG.indd   1
GX-BT3_QG.indd   1                                                   2013-09-17   09:04:239-17   09:04:23

5  Bluetooth one touch connection via NFC
This audio system supports NFC-enabled device with Android
4.1, Jelly Bean and higher.             ¦  NFC connection for audio playback
Check that:
NFC tag set up                        Your device (smartphone/tablet) has an NFC function.
¦                                     ?
NFC function on your device is enabled.
?
Screen lock function of the device is off.
The NFC tags can be placed anywhere convenient to you.  ?  This unit is not in Eco mode.
The velcro tapes supplied will help to secure the tags onto   ?  Your device must be within 10 metres from the unit.
the desired location.                  ?  Touch your device
1
Caution:                                 to the supplied NFC tag.
Make sure that the NFC tag is placed on a ? at and level
?
surface.                                                          NFC tag
If you choose not to use the velcro tape, do not place
?
the NFC tag near metal surface to avoid connection   2   A pop-up window asking whether to proceed with the Bluetooth
interference during tagging.            connection appears on the device. Select .
The ‘connected’ message appears when the connection is
Keep all small parts away from children as they may be  ?
accidentally swallowed.                  complete.
3  Playback will start automatically, otherwise press play (on re-
1   Peel the separator off the velcro tape (loop type) and   mote control or source device).
stick it on a desired surface.       ?  Sound will be heard from the speakers of this unit via audio
streaming.
Your device must be within 10 metres from the unit.
Separator                   ?
Various Bluetooth operation buttons (remote control only)
Velcro                                   Press the button to play or pause.
tape
(loop type)
Press the button to skip up.
Press and hold to fast forward.
2   Peel the separator off the velcro tape (hook type) and stick it to the   Press the button to skip down.
rear of the NFC tag. Then place the tag onto the desired location.
Press and hold to fast reverse.
Velcro tape                Notes:
Separator
(hook type)                ?  To disconnect, simply touch your device to the tag again.
Regardless of which tag you used to establish Bluetooth
?
connection with this product, tapping your device to any
of the NFC tags again, will disconnect the Bluetooth con-
nection.
To listen to audio via Bluetooth connectivity without NFC
?
tag - refer “Pairing with other Bluetooth source devices”
rear view of the NFC tag             on page 7.
It takes about 6-8 seconds for a Bluetooth enabled device
?
(eg. smartphone) to establish Bluetooth connection with
this unit via NFC or manual connection.
6  Listening to Bluetooth enabled devices
PAIRING          4   Perform pairing procedure on the source device to detect this
unit. “SHARP GX-BT3” will appear in the detected devices
ON/
MUTE  ECO MODE  STAND-BY
list (if available) in the source device. (Refer the source device
BASS  TREBLE  VOL
BLUETOOTH  PAIRING  X-BASS  operating manual for details).
BLUETOOTH  AUDIO IN  Notes:
GX-BT3
Place the devices to be paired within 1 metre (3 feet) of
?
DIMMER
each other when pairing.
Some source devices are unable to display lists of detect-
?
RRMCGA343AWSA
ed devices. To pair this unit with the source device, refer to
the source device operating manual for details.
5   Select “SHARP GX-BT3” from the source list. If Passcode* is
required, enter “0000”.
Pairing with other Bluetooth source devices  * Passcode may be called PIN Code, Passkey, PIN number
¦
or Password.
1   Press the ON/STAND-BY button to turn the power on.  6   Pairing indicator (blue) will stop blinking once the unit is suc-
2   Press the  BLUETOOTH button on the remote control or   cessfully paired with the source device. (Pairing information
FUNCTION button repeatedly on the main unit to select   is now memorised in the unit.)
Bluetooth function. (Pairing indicator blinks.)  Some audio source devices may connect with the unit au-
tomatically after pairing is completed, otherwise follow the
3   Press and hold the PAIRING button for 3 seconds or more.
instructions in the source device operating manual to start
PAIRING indicator blinks quickly. The unit is now in pair-  connection.
ing mode and is ready to be paired with other Bluetooth
source device.                       7   Press the play button on remote control or source device to
start Bluetooth streaming playback.
2013-09-17   09:04:259-17   09:04:25
GX-BT3_QG.indd   2                                                   2013-0
GX-BT3_QG.indd   2