Объектив CANON EF 35mm f/2 IS USM. Инструкция на английском языке

Nomenclature
?
? Distance scale
EF Lenses                                  ?
? Distance index
?
? Focusing ring
EF35mm f/2 IS USM                                               ?
? Focus mode switch
? Image Stabilizer switch
Instructions                               ?
?
? Lens mount index
?
? Contacts
Thank you for purchasing a Canon product.                   1. Mounting and Detaching the Lens
?
EF35mm f/2 IS USM is a wide-angle single focus lens that provide high   See your camera’s instructions for details on mounting and   ?
image quality.                                              detaching the lens.
? “IS” stands for Image Stabilizer.
? “USM” stands for Ultrasonic Motor.                            ? After detaching the lens, place the lens with the rear end up to
prevent the lens surface and contacts from getting scratched.
Safety Precautions                                           ? If the contacts get soiled, scratched, or have fingerprints on
? Do not look at the sun or a bright light source through the lens   them, corrosion or faulty connections can result. The camera
or camera. Doing so could result in loss of vision.             and lens may not operate properly.                                      ZER
Looking at the sun directly through the lens is especially hazardous.  ? If the contacts get soiled or have fingerprints on them, clean   MF  OFF
?
? Whether it is attached to the camera or not, do not leave the   them with a soft cloth.                                ?
lens under the sun without the lens cap attached. This is to   ? If you remove the lens, cover it with the dust cap. To attach it
properly, align the lens mount index and the 0 index of the dust
prevent the lens from concentrating the sun’s rays, which could cause   COPY
a fire.                                                         cap, and turn clockwise ?? . To remove it, reverse the order.
Handling Cautions                                          2. Setting the Focus Mode
? If the lens is taken from a cold environment into a warm one,   To shoot in autofocus (AF) mode, set the focus mode switch to AF ? .
condensation may develop on the lens surface and internal   To shoot in manual focus (MF) mode, set the focus mode switch to MF,
parts. To prevent condensation in this case, first put the lens into an   and focus by turning the focusing ring. The focusing ring always works,
airtight plastic bag before taking it from a cold to warm environment.   regardless of the focus mode ? .
?
Then take out the lens after it has warmed gradually. Do the same   After autofocusing in ONE SHOT AF mode, focus manually by   ?
when taking the lens from a warm environment into a cold one.  pressing the shutter button halfway and turning the focusing ring.
? Do not leave the lens in excessive heat such as in a car in direct   (Full-time manual focus)
sunlight. High temperatures can cause the lens to malfunction.
3. Infinity Compensation Mark
Conventions used in this instruction                       To compensate for shifting of the infinity focus point that results from
Warning to prevent lens or camera malfunction or damage.  changes in temperature.
The infinity position at normal temperature is the point at which the
Supplementary notes on using the lens and taking pictures.  vertical line of the distance scale L mark is aligned with the distance
?
index ?.                                                      ?    Infinity compensation mark
For accurate manual focusing of subjects at infinity, look through
the viewfinder or look at the magnified image* on the LCD screen   2.3  6.5     f t
while rotating the focusing ring.                              0.7   2          m
* For cameras with Live View shooting capability.                      22 11 11  22
Distance index

4. Image Stabilizer                                             ? Part of the picture may be blocked if the hood is not attached properly.
?
You can use the Image Stabilizer in AF or MF mode.              ? When attaching or detaching the hood, grasp the base of the hood to   ?
This function provides optimal image stabilization depending on    turn it. To prevent deformation, do not grasp the rim of the hood to turn it.  STABILIZER
shooting conditions (such as shooting still subjects and following shots).                                                         ON   OFF
1. Set the STABILIZER switch to ON ? .                      6. Filters (Sold Separately)
? If you are not going to use the image stabilizer function, set the   You can attach filters to the filter mounting thread on the front of the lens.
switch to OFF.
2. When you press the shutter button halfway, the Image Stabilizer will   ? Only one filter may be attached.
start operating.                                              ? Use a polarizing Canon filter (67mm).
? Make sure the image in the viewfinder is stable, then press the shutter   ? To adjust the polarizing filter, first remove the lens hood.
?
button the rest of the way down to take the picture.                                                                    ?
7. Extension Tubes (Sold Separately)
? The Image Stabilizer cannot compensate for a blurred shot   You can attach extension tube EF12 II or EF25 II for magnified shots.
caused by a subject that moved.                       For shooting distance and magnification, see the extension tube
? The Image Stabilizer may not be fully effective if you shoot from   specifications.
a violently shaking vehicle or other transportation.
? The Image Stabilizer consumes more power than normal      MF mode is recommended for accurate focusing.
shooting, so fewer shots can be taken if you use the function.
? When shooting a still subject, it compensates for camera shake   ?  The extenders cannot be used with this lens.
?
in all directions.                                    ?  The close-up lenses cannot be used with this lens.         ?
? It compensates for vertical camera shake during following   ?  CASE (Sold Separately) LP1116
shots in a horizontal direction, and compensates for horizontal
camera shake during following shots in a vertical direction.  This device complies with Part 15 of the FCC Rules. Operation is subject to the
COPY
? When you use a tripod, the Image Stabilizer should be turned   following two conditions: (1) This device may not cause harmful interference, and (2)
off to save battery power.                             this device must accept any interference received, including interference that may
? The stabilizer is equally effective for handheld photography and   cause undesired operation.
photography with a monopod. The Image Stabilizer effect may   Do not make any changes or modifications to the equipment unless otherwise
be reduced, however, depending on the shooting environment.  specified in the instructions. If such changes or modifications should be made, you
? The Image Stabilizer also operates when the lens is used with   could be required to stop operation of the equipment.
extension tube EF12 II or EF25 II.                     This equipment has been tested and found to comply with the limits for a class B   Button
digital device, pursuant to part 15 of the FCC Rules.
? If you set the camera’s Custom Function to change the   These limits are designed to provide reasonable protection against harmful
assigned button to operate the AF, the Image Stabilizer will   interference in a residential installation. This equipment generates, uses and can
operate when you press the newly assigned AF button.   radiate radio frequency energy and, if not installed and used in accordance with
5. Hood (Sold Separately)                                    the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
The EW-72 hood can keep unwanted light out of the lens, and also   installation. If this equipment does cause harmful interference to radio or television
protects the lens from rain, snow, and dust.                 reception, which can be determined by turning the equipment off and on, the user
To attach the hood, align the hood’s attachment position mark with the   is encouraged to try to correct the interference by one or more of the following
red dot on the front of the lens, then turn the hood in the direction of   measures:
the arrow until the lens’s red dot is aligned with the hood’s stop position   •  Reorient or relocate the receiving antenna.
mark ? .                                                     •  Increase the separation between the equipment and receiver.
To remove the hood, hold down the button on the side and turn the hood   •  Consult the dealer or an experienced radio/TV technician for help.
in the direction of the arrow until the position mark on the hood aligns
with the red dot ? .                                                          Extension Tube Specifications
The hood can be reverse-mounted on the lens for storage.                                                       Magnification  Focusing Distance Range
(Sold Separately)                    (X)             (mm) (inch)
EF12 II     0.60-0.36       168-197 (6.6-7.6)
EF35mm f/2 IS USM
EF25 II     1.04-0.79       158-160 (6.2-6.3)
Specifications                                                                                                                          * Sold Separately
Angle of view         Lens    Minimum     Max.     Min. focusing   Filter   Max. diameter and
Diagonal  Vertical Horizontal  construction aperture magnification  distance  diameter  length  Weight   Hood*  Lens Cap  Case*
EF35mm f/2 IS USM    63°     38°      54°      8-10       22       0.24x    0.24m/0.79ft  67mm    77.9x62.6mm   335g/11.8oz EW-72    E-67ll  LP1116
(3.1”x2.5”)
CT1-8586-000                        1206SZ                         © CANON INC. 2012